Reviews
Fits: KAWASAKI ZZR250, KAWASAKI ZZR250, KAWASAKI ZZ-R250, KAWASAKI ZZ-R250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZZ-R250, KAWASAKI KR-I., KAWASAKI KR-1R, KAWASAKI ESTRELLA
OEM Product has been discontinued.
I bought this because I thought the speedometer was probably out of cable because it stopped displaying the speedometer. At first, I tried to purchase a Kawasaki OEM Product, but it was out of stock, so I was wondering what to do. After disassembling the unit, I found that the Cable was also out of order, so I replaced it with this one and the Speedometer worked fine. View detail
It is easy to install.!
OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good.
View detail
Fits: HONDA Ape 100, HONDA Ape 50, HONDA Ape 50, HONDA Zoomer, HONDA Zoomer, HONDA solo, HONDA byte, HONDA monkey, HONDA monkey, HONDA MONKEY BAJA, HONDA MONKEY, HONDA DREAM50, HONDA JOKER90, HONDA ZOOK, HONDA JOKER Helmet, HONDA GORILLA, HONDA GORILLA, HONDA APE 100 TypeD, HONDA APE TypeD
APE 100
[How is it used?
Was the one you received as per Image? Yes
Was the installation difficult? No
How was your experience with it? Sounds good
[Included Parts:were they on? Stop lamp (Red)
[Was there anything that disappointed you? I wanted Gasket to be included.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Japanese Vehicle Inspection Correspondence
Before the inspection of SR400, I went to the tester place off site to check the light intensity. I had to go back and forth to Tester two years ago, but they did it without any extra charge, I switched to the new Stanley Hyper Halogen LightValve, which I brought with me again. It is just 150mm away from the specified light level, but it is OK.... Hyper Halogen Light is a high efficiency valve and can be brighter with the same power consumption as the standard valve, but it seems to have a shorter life. View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI ST250, SUZUKI katana, SUZUKI GSX-R1000
GSX-S125 2023 has differences such as Wiring allocation
[How is it used?
Installed on a DL32D GSX-S 125 2023, used to take out ACC power from a DAYTONAD-UNIT WR. (I plan on wiring the D-UNIT WR with Fog and Others additional power system)
Was the one you received as per Image?
No problem.
Was the installation difficult?
When installed on a 2023 model (DL32D), the ACC (+ wire for Attachment) and GND (Grounding Wire) of this product are reversed. In my case, I connected the ACCPower Cord of D-UNIT WR to the GND wire.
Also, in the 2022 and earlier models, a blind lid was attached to the connector on the body side of the GSX-S 125, and there was no connection beyond that point, but as shown in the photo (…) in the 2023 model, another connector was connected beyond the connector on the body side, and the wiring seemed to extend beyond that point. As you can see in the photo (…), in the 2023 MODEL, another Connector is connected to the end of the Connector on the Body side, and Wiring seems to be extended to the end of the Connector.
Therefore, we disconnected the OEM's Connector and inserted our product between them.
How was your experience with it?
The objective of getting ACC power was achieved without any problem.
[Included Parts:were they on?
users' manual
[Was there anything that disappointed you?
Not particularly
Some may consider this product to be price sensitive, but I think it is a good choice because it can be quickly returned to NORMAL when sold.
View detail
Fits: HONDA CB400 Super Boldor, HONDA CB400 Superfor, HONDA CB400 Super Boldor
feeling of being tightened
The panel is simply affixed to the meter, but the gold color around the black meter stands out and makes it look tighter.
I am very satisfied with the product, although it is not visible from the exterior, so it is a self-satisfying product.
View detail
Fits: BMW HP4, BMW S1000R, BMW S1000RR
Appeal full score
Installation is very easy. No modification, no drilling, nothing at all. 3Pattern Stop-lamp and 3Pattern Blinker are available for your enjoyment. The instruction manual was not included, but it is clearly explained in the video, so I had no trouble. I am satisfied with my purchase of Large. It is cool. View detail
Fits: KAWASAKI ZZR250, KAWASAKI ZZR1200, HONDA VTX1800, KAWASAKI ZX-12R, KAWASAKI ZX-11, KAWASAKI ZRX400-2, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1000R, HONDA CB1000SF, KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI ZEPHYR1100, KAWASAKI ZR-7, KAWASAKI Z1000MK2, KAWASAKI Z400GP, KAWASAKI Z1, KAWASAKI W800, KAWASAKI W650, KAWASAKI NINJA250SL
It got brighter.
I purchased this because Light was dark.
It brightened up as expected!
View detail
Bright!
The OEM was dark, so we replaced it with a new one and the custom feel is improved.
[Color] I chose Smoke and it is not too Black.
View detail
Was good
The product arrived quickly because I was out of bulbs. View detail
Fits: YAMAHA
Seems a little high.
Feels a little unstable in the mounting position View detail
There is a sense of security dedicated to the car model.
DL1000 V-STROM650XT ('22) The product has been installed in a
It will be used in conjunction with Hepco&Becker's Engine Guard,
The bracket of the Radiator part was a little bit hit by the Guard,
The installation was only a little difficult, but it was almost interference-free. I think there may be individual differences, so this is just for reference.
Because the connection between the Fog Lamp and the included Harness was a Flat Terminal,
We changed to WaterproofCoupler just in case.
The brightness is sufficient for an auxiliary light,
Cutline is also solid, so I don't think it will bother oncoming traffic.
Considering the price, the texture might be a bit lacking,
If you are concerned about this, you should consider another product.
View detail
Service Reminder Reset for New Model GSX1300R HAYABUSA
[How is it used?
Recently, many manufacturers have adopted a system in which the Lamp on the Meter lights up when it is time for maintenance.
Various foreign car manufacturers, especially Ducati, are doing this.
But recently, domestic cars are also becoming like that:you have to drop Gold to the Dealer to get rid of the Lamp. Is this part of the Dealer's business strategy? So, even for a simple oil change, if you don't go to the Dealer to have it done, the maintenance Lamp is still glowing all the time.
is Japanese pampas grass, a simple homemade one is all that is needed to solve the problem.
Was the one you received as per Image?
As per Image
It's better to buy it with other things. Since it's only about $100 anyway, the actual store is a better deal when shipping is included.
How was your experience with it?
Effective.
[Points to note]
You have to insert it deep to get it to work.
How did it compare to other products?
Nothing in particular to compare.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
In doing the work, this method is probably a maintenance procedure that is not covered under warranty.
If you want to be stingy with your Gold, please use it only as a reference.
If you are a little worried about the work, you should still buy the OEMReset switch.
OEM reminder Reset switch
09930-83130 Available at Webike, but currently out of stock?
By the way, in most cases, they fail.
It will not respond unless it is inserted firmly and deeply.
Then press and hold the LeftSelectSwitch▼Button to open MENU, select SERVICE, MODESwitch to determine RESET, which is not usually displayed, select Yes when Yes/No appears, and then you can set it individually!
View detail
A quality low-profile blinker kit
The kit I purchased was well packaged and tailored for installation on a V-Strom 650. All parts appear to be good quality and ready for immediate installation on the bike. The kit includes wiring adapters to suit the bike (bullet connector to 2-pin Suzuki connector) and a new 7-pin LED blinker relay. Installation was easy for someone with moderate experience. Tools required: open-end wrenches (8~12mm), hex key wrenches (4~5mm), 10~12mm socket. The rear fender of the bike must be removed to access the wiring and remove the existing blinkers. Routing the wiring through the adapter plates, washer and nut requires patience and a delicate touch. Aside from that, it's a matter of securing connections with electrical tape and securing the wiring to the frame. The kit is quite bright and very visible, even during the daytime. The blinkers are all mounted on flexible stalks, so they should survive if the bike is dropped. Overall, I am very pleased with the purchase. View detail
It does not require processing. The lid is a bit ….
The USB power supply can be removed very easily if you don't feel the need to remove the front parts, which are the face of the motorcycle. If you don't feel that removing the front parts and drilling holes in the body is too much work, you can take out the USB power supply very easily.
It is not difficult if you have a set of tools used for maintenance. Drilling was done halfway using a plastic cutter, Nipper, and File.
Wiring is completed by simply joining the existing Connector, which is the quintessential OEMAttachment.
It is also helpful to be able to download the illustrated Instruction Manual.
Material for Waterproof:It has a rubber lid, but the fit is squishy and unreliable, and it hits a nearby screw when closed, so it's not great here.
Aside from the amount of work and quality, I wonder if the most appealing feature of the Large is the ability to take out the USB power supply without any wiring process.
For reference, it took about 2~3 hours to do the work by hand.
View detail
The price is ….
It looks cool, but as with all RS parts, the price is too high! View detail
Fits: Others
The Connector part is Compact, but the Body box is in the way.
As a result of changing Navigation from 5-inches to 7Inch, when connecting Navigation power to the USBConnector on the BOLT Shoulder Bag
It became difficult to do, so I thought it would be a good opportunity to replace it with this product, which is 2.4A compatible.
As mentioned in the Title, the Connector is compact and unobtrusive, but the Body (transformer from 12V to 5V?) is not. However, the Body (transformer from 12V to 5V?) is
I was worried about the mounting position because it is bulky.
Finally, it is fixed with Double-sided Tape on the Front side of the Top Bridge, which is hidden by the Bullet Cowl.
Red wiring is very noticeable as it is, so the Bullet Terminal is cut out and soldered on.
Spiral Tube and Wiring Cover were used to prevent the Red color from being seen.
The Connectors placed on the Handlebar are Compact and unobtrusive, so they look good when not in use.
View detail
Easy to secure power supply
It is an excellent and easy way to secure power. View detail
It picks up Noise.
I thought I knew what ShiftTiming was even without the Tachometer.
The re-acceleration is inevitably slow in the SCENE that requires climbing the board.
I purchased it to keep track of RPMs.
While retrofitted, the position and Size are moderate, and the high brightness makes it easier to read than the OEM Speedometer.
However, the Clutch Cable runs through the Shift Up Indicator position, so it is not visible when the driver is riding. (I guess it depends on your body shape …)
Also, as is common with retrofitted tachometers, the rpm may rise or fall by around 500 rpm during cruising.
The performance is sufficient for me as I only needed to know the approximate number of revolutions.
I was able to correct my riding style because I was SHIFT UP at lower rpm than I expected.
The installation is more difficult because the tank needs to be lowered.
The illustrated Instruction Manual is clear and helpful and manageable.
However, although not a problem with this product, we had two problems during installation.
1. OEM Speedometer BracketMounting Bolt stuck at an angle.
It is fixed by biting into the Blinker Bracket and Meter Bracket.
The Bolt on the Meter Bracket was stuck at an angle, making it difficult to replace the Bolt.
(It's mainly Honda's fault since it's due to individual differences in the car body.)
2. occupies the power supply for Attachment (+ voltage shortage may occur)
The power supply for the Attachment provided on the Brake Side is used.
Already incompatible with USB power supply and Cigar socket.
The same thing happens when I make the connections as per the Instruction Manual, but
While the Cell is spinning, it seems to run out of voltage and reboots (re-opens).
The Harness length is long enough to reach the bottom of the Seat even through the bottom of the Tank.
I modified the Wiring to take power directly from Battery and it improved.
The voltage display function compares the voltage at the time of wiring according to the Instruction Manual with the voltage at the buffer.
The voltage seems to be slightly lower in the former. (It is not the fault of this product, but the spec. on the car body side.)
The following products were used for the Wiring change.
KIJIMA:ACC Branch Harness Kit]
https://www.webike.net/sd/21317023/
DAYTONA:Attachment Power Supply Unit D-UNITPlus]
https://www.webike.net/sd/24232600/
View detail
Fits: HONDA CB300R, HONDA CB125R, HONDA CB250R
It's difficult, isn't it?
I put Meter's Film on the new car.
I thought it was no different than GlassFilm for cars.
He applied it with a mild detergent.
Eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee dust ・・・・ tears
That's a tough one.
I wouldn't worry too much about it since it's for Meter Protection purposes.
Fortunately, it is expensive and contains two different types of films.
I'll try again next time.
You must be a PRO to be able to do this so beautifully.
View detail