Reviews
Purchased for CB750four
[How is it used?
Blinker Bracket for CB750four
Was the one you received as per Image?
Yes
Was the installation difficult?
it's simple
How was your experience with it?
Image
[Included Parts:were they on?
Nut, Washers
[Was there anything that disappointed you?
The outer diameter was a little small or there was a clearance on the joint surface with the blinker, so we made the outer diameter larger by using aluminum tape.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
The color...
I bought Black, but it was not Black, it was a bit greenish Black. View detail
Fits: KAWASAKI 750SS Mach IV (H2), KAWASAKI 750SS Mach IV (H2)
MeterOverhaul and at the same time
Replaced at the same time as the Meter Overhaul.
After all, a new one is soft and good
View detail
NORMAL is too long …
This is a personal taste, but I replaced the large blinker with a short one because the too long bracket doesn't look like a Race ish.
Quantity with European Blinker:Race ish look with Set
Personally I like it.
View detail
Just right Size
Changed to this size because I don't like too Large Blinker.
I have no problem using it.
Race ish old car with Exactly
View detail
Surprisingly, the work is Large strange
If you start with a light heart to replace it with a new one quickly and easily, it is Large strange.
No problem as a product.
I used it with MACH, and after replacing the hardened rubber, the vibration is naturally reduced, but as I mentioned earlier, the work is quite Large strange!
View detail
Let's clean it up.
Purchased to clean up front and rear Blinker
It looks good with Short Bracket.
I want to clean it up because I'm going to be there, right?
View detail
It is attention
One Side, so be careful who you buy!
No problem at all as an item.
View detail
The keys to the old car are …
I'm of the school that if you buy an old car, you replace the key.
It's also theft-proof.
These parts are helpful.
View detail
Fits: KAWASAKI Z1000, KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z1000 MkII, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z1000 MkII, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4)
It is safe.
Well, it's like this ….
It's just right for Refresh for now!
View detail
He wanted to use the present S ball as W ball, and it was purchased. They are goods which may be cheap.
He wanted to use the present S ball as W ball, and it was purchased.
They are goods which may be cheap.
View detail
Fits: KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z1000 (air-cooled), KAWASAKI Z1-R/Z1-RII
Reproduct
Electric wiring on older cars should be replaced as much as possible, including the 6V MONKEY/GORILLA Main Harness, Regulator, BatteryLEAD, Blinker harness, and Tail lamp.
You never know when or where a wire might break.
View detail
Fits: KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000
Bolt holes
The Mounting Bolt hole did not fit and I had to cut about 1.5mm off the long hole side.
The RegulatorBody is also very large, so I installed the Connector side upside down.
It's in good working condition, 14.6V, and it's charged.
If you think you can replace the battery with a sealed MFBattery with a little modification, this product will be large and durable.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
Tape wrapped around Harness is messy
For connection and installation, please refer to the included Installation Manual and Wiring Diagram.
I don't think it's that difficult.
The only problem is that the brackets and relays are sent in RoseRose, so it was a bit of a pain to assemble them and get them to the car.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
Waterproofness is questionable.
I used it to convert the front tire of Kawasakiz1 to 18-inches.
The front hub bearing is not covered like the NORMAL meter gear, and the bearing is exposed, so there is a question about waterproofness.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR)
Which one do you choose?
OEM Parts are still available. The price is not so different. What is the quality of Rubber?
Which one shall we choose?
View detail
Quantity:I thought it was 1 Set of 2pcs.
2 Quantity because the picture was taken with 2 pieces.:I ordered this thinking it was a Set but it was 1pc. The brightness is not a problem. View detail
Long tail cowl essentials
PMC Long tail cowl and
Used with PLOT's Fender Eliminator Kit.
Installation is the easy part.
If you can make Fender Eliminator by yourself, you can work on Level without any problem.
The wiring extension was also very large and sturdy by just connecting the connector of the attachment, although the Instruction Manual said to cut the terminal.
However, is it individual difference? On my guy, there was more gap between Stop-lamp and Cowl than I expected.
Personally, I'm not convinced Forme.
It's a shame, but I decided to replace the entire rear area and this extended bracket set is now ready to go.
View detail
Compact
I like the design and compactness of PMC. I like the design and compactness. (88mm) I also bought a Bracket and I'm posting an impression. Please refer to it. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
Usually. That's a compliment.
I think that the cable connection should have a little more offset.
More or less, it has been Offset.
What we are looking for is a long term MaintenanceFree
There is no quick answer.
It's well made and I have no worries.
It's a necessary part when replacing 19-inches to 18-inches, so
I'm glad you offered something new to assemble.
If you choose 18Inch type, the meter cable of OEMSize is not attached.
Please keep this in mind for future Cable replacements so you don't buy the wrong one.
View detail