Reviews
Horn.
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
If you energize it and turn on the Switch, you can use it normally.
The volume is also sufficient.
View detail
It is quite convenient to have it in Single Body.
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
This will bring together the electrical system for the time being.
The terminal connections are in good condition and are securely fastened with Heat Shrink Tubes, so they appear to be water resistant.
View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
I'm not sure about the electrical system, but ….
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
These are the Parts that are required when using LEDs with DRC's Kit.
View detail
A little bit of installation. ? Will be
As others have mentioned in the review, the convex part to fit the lower cosmetic bolt×1 and the upper OEM bolt×2 do not fit if they are left as they are.
The lower inner side is fitted by grasping and compressing the inner side with your hand.
I am a little impatient because this area is not in the Instruction Manual.
I am not sure if it is only for the 2023 model, but there is a 5mm pin hole on the inner cowl side, which is flooded with slop water, so I filled it with Pate.
You can see it when you actually fit it, but it is a pin hole that does not bother you that much, so those who do not mind may not mind it.
I wanted the Fender angle to be a little more warped, but since it is a regulatory Limit, other Fender Eliminators may be the same.
View detail
Conforms to ST1000 Regulation
I purchased the Tail Lamp to compete in the ST1000Class at the regional championships.
I purchased the DRC Tail Lamp because it meets the ST1000 Regulation.
Brightness is not a problem.
View detail
DRC MeterScreen ProtectiveFilm
Even if air bubbles appear, they will disappear in a few days, making it easy for beginners to apply.
If it fails, it is conscientious because it comes in a two-pack.
View detail
DRC MeterScreen Protect Film
It is very easy to put it on.
Even if there are some bubbles, they will come out in a few days.
No more worries about scratching.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
I wish it was 10mm diameter.
Purchased to replace LED Blinker.
Maybe it's compatible with Yamaha stuff or something.
Since I could not be sure, I bought a DRC product that I could be sure of.
This product is used between two pieces, so the front and rear blinkers are interchangeable.
2Quantity:Set is required.
Since the mounting hole of this product is 8mm diameter, the Screw diameter of the Blinker to be installed is also 8mm diameter.
The 8mm blinker is used, but there are surprisingly few 8mm-diameter blinkers.
The problem is that most of the products sold at low prices are 10mm diameter and there are very few options.
View detail
This is a highly Universal Tail lamp.
Universal Tail lamp
[How is it used?
I had been looking for a replacement for my KSR-II for many years, but I could no longer install the OEM Product's Tail lamp, so I went to Webike to find one. However, I found this product when I was looking for a replacement for the OEM Product's Tail lamp.
Was the one you received as per Image?
It is a product that is more than an image in the form that has good visibility with the Edge effective design while being compact, and also has universal characteristics that can be installed from off-road motorcycles to road sports type motorcycles without any sense of discomfort. It is a product that is more than just an image.
Was the installation difficult?
As mentioned above, this is a work to install a bracket for Fender Eliminator, which is a self-made bracket, so the drilling and wiring processes are performed in actual products, so it may not be of much help.
After installing it on the Fender Eliminator, all you have to do is connect the wiring of this product to the wiring for the tail lamp on the body of the vehicle, but this product does not have the wiring that is often found in this type of product. "Bullet Type Terminal Spec
Modern motorcycles have connector terminals, so it is easy to find a connector that fits the vehicle body on KITACOConveniencePartsetc. and modify it to make a simple connection.
Fortunately, KSR-II has Bullet Type Terminals for most of the terminals that connect to the lights, so we were able to connect without any modification.
How was your experience with it?
There are no problems with the functionality of the LED bulbs, which have been in place for several years now and are functioning as well as they did immediately after installation.
My personal impression is that the rounded design of the KSR Tail would fit better with the rounded design of the Tail lamp than the pointed design of the Tail lamp. I think that the rounded design of the KSR Tail lamp fits in better than the sharp design.
I had a friend install it on his WR250 after that, and the shape of the tail and the design of this product matched very well, and I honestly thought Parenthesis was good (this is just my personal opinion).
[Included Parts:were they on?
It was a Simple Package with only Body and Instruction Manual.
[Was there anything that disappointed you?
Not at all.
Aside from the above mentioned compatibility, which is a matter of personal preference, I have no complaints about the product design or the kinability of the product.
Other items that would be helpful
Point and hang of installation
This product is a Tail Lamp product, but a vehicle-specific kit that uses this product is also sold by DRC.
The price is a little bit higher, but the Bracket for each car model is also of high quality and you will not feel any discomfort after installation. It's a Manufacturer's product." I am convinced that this is the right product.
For those who, like me, cut, paste, and fabricate to install, please measure the dimensions carefully or do your best to install the product as-is.
[Availability and clarity of the Instruction Manual
An Instruction Manual is included in the package.
[Notes]
Nothing in particular, just be careful not to misplace Wiring.
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
Since the method of fixing to the car body varies depending on the car model, it may be better to try a temporary assembly before full-scale installation.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
Please keep up the good work in maintaining prices as much as possible and keep selling for a long time to come.
View detail
Thank goodness I can buy only Lens.
I know that Blinkers on off-road vehicles are often damaged in a fall, but it is very nice to know that DRC products are available only in Lens and can be replaced.
I was impressed that DirtFreak products understand Off-roadUser very well.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
For those who want to make the silhouette of the car look sharper...
I am an uncle who loves Fender Eliminator Large, so I was the first to replace it when I bought D-Tra.
Please note that if you buy only the product, you will not be able to use the reflector or the OEMB blinker, so you will need to purchase a reflector and a bracket to attach the OEMB blinker, which you may have lying around, before you can finally drive the product on public roads.
Now, as you can see in the image, the weight is reduced due to the overwhelming difference in area.
This doesn't mean that it is lighter or anything, but it is lighter (lol).
I personally thought that the Rear area was cleaned up and the finish was very cool.
View detail
Simple shape
OEM and replacement.
There was a Space-like difficulty in installing it on the Fender Eliminator Kit.
No Large problems.
As said in other Reviews, note that Body strength is low.
Also, be careful when converting old cars to LED because it is easy to have problems with Relay.
View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
Did not work well
XR250MOTARD, used for front and rear Blinker LEDs.
It did not work well.
Specifically, I have become a high flasher.
Honda's Front blinker seems to be a bit special as it also serves as a position.
View detail
Fender Eliminator and led
[How is it used?
Fender Eliminator conversion made it look like I like it, as per Image.
Was the one you received as per Image?
It was heavier than I expected.
Was the installation difficult?
I had a little trouble with the installation.
The lower mounting part attaches to the outside of the
I couldn't figure it out and tried to install it on the inside.
I was worried that it would not fit.
How was your experience with it?
It's good
I have no protection against rain or water from washing the car.
We'll see how it goes.
[Included Parts:were they on?
Screw has some parts to be diverted.
[Was there anything that disappointed you?
Instruction Manual, because we are making it universal.
I don't know much about it.
I feel like I can handle it.
Other items that would be helpful
Buy together
Reflector kit for D45-07-300 has been
I think it is necessary.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Quantity:1 Set of 2pcs. is Point
Quantity:1 Set of 2pcs. would be appreciated.
If you are going to put it on, it would be better to do it as soon as possible in a new car or after a thorough cleaning. The two-lens meter is a little curved, so you may need to hang it.
Although it is a good product, the included spatula is made of paper, so when it absorbs moisture, it becomes soft and difficult to apply.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Safe if you put it up first.
Once it is applied, it blends in so well that you can't even tell it's there.
It is good for preventing scratches, and if it should get damaged, it may only be a matter of replacing the film.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Quantity:1 Set of 2pcs. is good
The first one failed.
Apply a large amount of Film Paste Spray to the film and paste it well.
The second one went on well. It's so good that you can't even tell it's on.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S750, SUZUKI SV650, SUZUKI SV650X
more than I thought
I bought two pairs, thinking they would not stick nicely. But they were easier to install than I expected. Highly recommended. View detail
Careful work was essential for the softer TPU.
It was affixed as protection against the odd summer heat and direct sunlight.
First, I will list the items that were of interest to me in the work and that I think should be noted.
In addition, it is necessary to prepare a water spray container, a small-size film scraper, kitchen paper, and a paper windshield wiperetc.
We believe that it is better to proceed one by one without haste, except for PROs, so as not to make mistakes.
The first thing to note is that dust removal should be thorough, pointing to the included Kit for a clean finish.
Next, positioning should be done carefully and securely. If this is not done properly, the paste will not be applied properly.
Then, check to make sure there is no TPUFilm left on the release paper on the Meter side! After confirming that there is no residue of TPUFilm on the release paper, spray a large amount of water on the Meter side and the mounting surface to prevent shifting, and then gently place the TPUFilm on the Meter side and the mounting surface.
(I thought this was Large! I didn't notice and wasted the first one with the film still on the release paper...)
Finally, turn up the upper yellow release paper a little and spray it with plenty of water using Spray, then use a scraper on the upper side of the yellow release paper! and then eject the air from the top side of the yellow peeled paper in each direction.
I stuck it on anyway, thoroughly and carefully checking and not compromising.
Unlike the W, this soft TPU film is thin and stretchable, so I thought it would be as easy as the hard film for the W. However, I failed in both the display and the tachometer portion of the first sheet. (Sweat)
The second one was barely successful in attaching both, and the installation process was both a relief and a satisfying experience.
After the application, there will be some white traces until the water dries, but after it dries, the finish will be clear and beautiful.
Maybe the price and the work will protect it well from UV and WOUND.
It has been a year for the W and it still looks the same as when it was applied, so I expect it to be more durable in the future.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
DRC MeterFilm
It was very difficult to install, I bought it for Z900RS and it goes on without any problem. View detail