Reviews
Simple configuration
[How is it used?
Since the Fender Eliminator Kit was relocated, the Reflector that had been used until then could no longer be used, so we chose this one with the License Plate co-tightening type.
Similar products are available from Active and KIJIMA etc., but I chose DAYTONA's because it was in stock and inexpensive.
Was the one you received as per Image?
It was just like the picture.
The condition of the paint was also fine.
Was the installation difficult?
Replacement is easy as it is simply tightened together with the bolt on the License Plate.
One Side at a time, you can remove the Bolt and slip it into the gap and not worry about dropping it.
How was your experience with it?
Naturally, it was Exactly to the Size of the License Plate.
Visibility is also sufficient.
The Cushion works well and the contact with the Number is just right.
[Included Parts:were they on?
Mount, Reflector and anti-vibration Cushion are included.
[Was there anything that disappointed you?
Not particularly
【Review】
It is an inexpensive and solid reflector when converted to a Fender Eliminator Kit.
Of course, it also passes vehicle inspections, so it is safe for vehicles that are subject to inspections.
View detail
Inexpensive and fully functional
Used when converting an off-road motorcycle to a Fender Eliminator.
I also had to repurchase the product because it was broken in a fall, but the inexpensive and simple installation method made it easy to fix.
It also functions perfectly, including the reflective condition.
DAYTONA products with a large lineup of such basic parts can be trusted.
View detail
My car ZX-6R is also like Motorcycle for International Model.
What was the deciding factor in your purchase?
Side reflectors are standard equipment on motorcycles overseas, and I believe that side reflectors increase the visibility of motorcycles and also help prevent accidents if drivers around you notice them by timing their vehicles quickly. I think it will lead to the prevention of accidents. I installed side reflectors on my ZX-6R as well, just like those for International Model motorcycles.
[How was the product?
EMark Income Reflector, OD is 40Φ, M6 Bolt Fixed Nut with Washer.:1pc., so Quantity:Pair (for Left and Right) Two must be purchased if they are to be matched.
When installing on the ZX-6R, the ReflectorSingle Body hits the Front Fender, so we used KITACO's aluminum spacer collar 5mm and a polycarbonate washer. However, the Bolt's bite is reduced by the amount of spacer, so we installed the Bolt firmly to prevent it from coming off. We are now thinking of measures to be taken in the future.
[Others]
Side reflectors will also be mandatory for New Model vehicles to be certified by the government after September 2023. This revision of the safety standard applies to New Model vehicles that will be certified by the Japanese government in September 2023 or later, and side reflectors are not required to be installed on motorcycles manufactured before that date. However, these parts will increase visibility, although not absolutely, and help prevent accidents by making drivers and pedestrians around you aware of your vehicle by timing it earlier. You may want to consider installing them, especially if you drive a lot at night.
View detail
Reflector
[How is it used?
Was the one you received as per Image?
It was as shown in the Image.
Was the installation difficult?
Easy to install
How was your experience with it?
Size was just right.
[Included Parts:were they on?
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Very Simple
I think it is solid, not cheap.
I like the fact that Reflector is not blobby.
For DIY installers, please be careful not to forget to buy the License Plate Light.
(I bought it without reading the description carefully and could not install it on my 400cc motorcycle lol).
I would like to utilize this in the future when converting a 125cc Motorcycle into a Fender Eliminator.
View detail
For EXC-F public road driving
I bought it at a Dealer, but when I brought it in for inspection, it did not have a License Plate Light and Reflector, so I installed them to avoid being caught.
Since it is a 15 year old model, there are no angle restrictions, but we have a 45 degree one.
Installation is easy, but it is a pity that it interferes with the KTM License Plate, so it can no longer be used.
Now I just hope it doesn't break and lose it due to vibration.
View detail
Standard for foreign Enduro racer
I use it often. I think this is the standard product when installing numbers on a foreign Enduro racer, and it requires a lot of modification to install. I like that the reflector is designed horizontally and does not interfere with the rear tire when stroked. View detail
![Repair Parts ] Hi-Vis Mirror Mirror Housing Round](https://img.webike-cdn.net/catalogue/images/71226/16002_TS.jpg)
Repair Parts for a great price!
DAYTONA Hi-Viz Mirror's
Only the Mirror part is used as Repair Parts.
I purchased and immeChain at a great price.
It is a good Mirror with less blurring while driving.
View detail
Installed together with SEROW250 DRCFender Eliminator.
The Fender Eliminator Kit from DRC was installed on the SEROW250 to eliminate the reflector.
It would be Sporty without it, but since it is a Rule, it must be installed. Without it, it will be treated as poor maintenance.
The KIJIMA License Plate Base is installed in the back, but it could be installed with the existing bolt.
View detail
Satisfied with the new look and feel
I was looking for a round mirror that could be attached to the bolt of the Right Side Opposite Thread Screw without an adapter, but I couldn't find anything like it, so I decided to purchase this product's Mirror Bracket and Fixing Bolt in quantity.:Pair (for Left and Right) Purchased at Rose.
Quantity:This is because there was no Round Type Opposite Thread ScrewSpec. available for sale as a Set (there is a Normal Thread Screw with security parts). (Normal Thread Screws with security parts are available)
I have not driven the car after installation, but I don't think I will be bothered by the slight shaking that occurs when the engine is revved up.
The Mirror part can be moved to some extent (30 degrees in all directions according to the manufacturer) even after it is fixed, making it convenient for fine adjustment.
Although a smaller Mirror would have been ideal, the Mirror's area meets safety standards.
It is a little harder to see directly behind the Mirror than the previous horizontal Mirror, but this may be adjustable by extending the Mirror section more to the tip of the Bracket. However, once fixed in place with the imonesi, that part of the Bracket can be " and marks, so it is better not to move around too much.
I used a spring washer to prevent loosening during installation.
At first, I used the ring on the base, but it was too loose, so I decided to use only the spring washer.
View detail
Fender Eliminator and Reflector installation.
From Motorcycle shop to GORILLA which has been a Fender Eliminator since purchase. I don't see a Reflector or a △Mark. I installed the Number using this kit, which is co-tightened with the NumberNut, and the Reflector is attached to the hole at the bottom of the Number to complete the installation. It was very easy. (You can also install the △Mark (sold separately) under the Reflector, but I will post my impressions of that in another post. My GORILLA has extended Swing Arm with Down Suspension, so it may interfere with Tire …. (So far it is Large sturdy.) It is a horizontal Reflector, which is fine in terms of area, but I am a little concerned about visibility. I like the fact that it looks Simple. View detail
Decline Rhythm in Simple
Reflector made by DAYTONA.
Used to modify a Fender Eliminator Kit on a CBR650F.
The image shows a reflector (KITACO?) that was given to us as a free gift, but in comparison, it is extended horizontally and looks stylish.
The structure is very simple and consists of a Bracket and a Reflector.
I think it would look great for use on a modern vehicle.
View detail
Since only this was put on the store, it used. Although it is completely satisfactory and very much satisfied about attachment and the engine performance, a rectangle style is not pleasing somehow. For a while, I had the reflector portion made sma
Since only this was put on the store, it used.
Although it is completely satisfactory and very much satisfied about attachment and the engine performance, a rectangle style is not pleasing somehow.
For a while, I had the reflector portion made small and it has already extorted it.
It is a good point when it collects. Bad point of - Not being found I wanted you to make - reflector a little smaller.
View detail
I think kana a little weak in reinforcement.
I think kana a little weak in reinforcement. View detail
[buying motive] The product ] which was seen as the candidate besides [point which got interested] [, [after-use comment], [comprehensive evaluation]
[buying motive] The product ] which was seen as the candidate besides [point which got interested] [, [after-use comment], [comprehensive evaluation] View detail
In ! which is not except this, a price... It is stylish anyhow.
In ! which is not except this, a price... It is stylish anyhow. View detail
Tiny.
Installed as a reflector when converting to Fender Eliminator.
The slim design allows for a tight fit without taking up too much space, and the Bolt&Nut fastening ensures that the unit can be used for vehicle inspections.
View detail
You can be too aggressive with License Plate Bracket.
When I assembled KIJIMA's Fender Eliminator Kit, I installed the angled License Plate Bracket & Frame together, but the Paste Type Reflector that came with it was not usable.
I felt that the angle was too aggressive, but I was relieved that the Reflector functioned well.
We plan to replace the License Plate Bracket with one with a more gentle angle at a later date.
View detail
Bracket is a bit short. Crying
I had to replace it due to a fender bender. (Reflector is Repeat)
DAYTONALicense Plate Holder99662 and Quantity as per the accident estimate made by Motorcycle shop.:I was compensated by Set and did the installation work myself.
Quantity in DAYTONALicense Plate Holder99662:The top of the Reflector square will interfere slightly with the top of the Reflector square when it is set, so you will need to modify it in some way. (The height of the outer frame of the License Plate Holder is less than 2mm higher. Is it compatible with the new standard?)
Reflector is blameless. (Lol)
View detail
Exactly
I replaced the Tail lamp with DRC's Mo Tread edgeTail and installed it together.
Installation is easy
The size is small, so the Tape area was refreshing.
View detail