Reviews
It is surprisingly noticeable when you put it on, which is good.
Used 4 pieces for Handlebar Clamp on XSR900.
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 is with O-ring.
I found out when I put it on that I can see the silver color of the Bolt. I am satisfied with it because I can't see it while driving.
View detail
Looking for ways to use it.
I was going to use it for a Handlebar Clamp on my XSR900, but it was not available in this size, so I ended up buying it in vain.
I ended up buying M6, M8, and M10, all of which are of good quality and may not be as expensive as they should be.
I've seen some of these products not match the color when you buy them, but the gold of this series is similar to the gold of the XSR900's Fork.
M8 and M10 are O-rings. We will keep them until we can find a use for them.
View detail
It looks surprisingly different and good.
XSRLogoQuantity under XSR900 Meter:Pair (for Left and Right) Used for
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 and M10 are O-ring, but M6 seems to be resin color.
View detail
Screwfor Hole
I didn't check it carefully, but it seems to be an M8 Screwfor Hole, not a product for filling a hole of M8Size. So the body is around M6 size.
It does not appear to fill the M8Size hole.
View detail
It would be nice to have a Type without Luster.
[How is it used?
TZr250R (3XV) I was concerned about the bare cap bolt on the Stem of the "Stem" so I bought it to put a lid on it.
I thought about using KITACOConvenienceParts, but I chose HURRICANE because it is a PRO around the handlebar and there were more of them.
Was the one you received as per Image?
1Quantity firmly as shown in the picture:It was 1 Set of 2pcs.
Was the installation difficult?
It can be installed in about 3 seconds as it just fits into the Bolt's head.
How was your experience with it?
As you can see in the photo, it is quite shiny, so it stands out a bit. (Lol)
Well, it can't be helped that it is probably intended for use in the bar Handlebar Post.
I'll try to get rid of the luster by easing it off a bit when I have time.
[Included Parts:were they on?
Cap only.
The bags are of a type that cannot be sealed, so it would be nice to have a Zip lock, etc. for storage.
[Was there anything that disappointed you?
Not really!
【Review】
It prevents Bolt from rusting and dirt from accumulating.
It is good for those who use it in such areas because of its gloss.
Also, since there are quite a few caps in the box, I will use them for cap bolt in places I am interested in.
View detail
It's cheap and can do dress-up, but …
Easily dress-up with no tools required! … but it fades quickly lol
I've had it for a few years… but it's cheap, so why not! LOL!
View detail
For M8 is a little different?
First of all, please note that this is not a product for attaching to the hex holes of the Cap bolt. Do not blame the Manufacturer if you misunderstand the usage of this product.
I thought about what to do with the Screw holes that I had left partially visible and neglected, and remembered that there was also For M6 in the product I had bought to plug the M8 holes.
If you pick it up and compare the two, you will see that the texture of the head is different for some reason (minor change?), but the basic structure is the same. However, when you try to use them, the feel is slightly different.
The M8 for M8 is small and fits into the hole very well, whereas the M8 for M8 is not so responsive. The M8 for M8 has a head that fits tightly against the Exactly and fills the hole without gaps, making it difficult to remove, while the M8 for M8 has a slight rattle and can be removed by inserting a nail and pulling hard. I wonder if it is due to the difference in Screw Pitch.
View detail
Tiny but unobtrusive.
The M10 Screw mounting hole for the Stand Hook on the Swing Arm of the ZrX1200 DAEG is not used in the future, so I installed this Hole Plug. Is it really for M10Screw because it is unexpectedly small? I thought it would work, but it fit perfectly (laughs).
Pushing and rocking so you won't get blown away. Black resin, unobtrusive and Good.
View detail
Glam up your Cap bolt
What made you decide to buy?
I purchased this product for the purpose of dress-up around OEMAttachment and Engine Guard.
How was your experience with it?
The appearance of the Engine area has changed a little. Probably, others will not notice if I don't tell them, but I am satisfied with myself.
This is the part you want to check before driving to make sure it won't come off due to vibration.
[Regarding installation]
Installation is easy, just insert it into the head of the Engine GuardMounting Bolt. However, when I bought it, it was difficult to insert into the Bolt, so I used a little silicon spray on the ORing and installed it.
View detail
Dress-up made easy
I bought this as a Cap for Fixing MirrorBolt.
I'm glad I put it on because every time it rains, the hexagonal hole part used to be a puddle of water.
Installation is also super easy, just lightly hammer in with a plastic hammer etc.
View detail
To prevent rust.
MirrorMounting Bolt tightening holes
There was a pool of water and Rust.
I bought a Cap!
There was one with and without a rubber at the end of the cap, but
The part to be used this time is the Bolt that attaches to the horizontal direction
So, is it Large sturdy without Rubber? I think so.
Does the size fit since it's a special bolt?
I was worried, but the Exactly/Fit
This way, there's no water pooling in the car wash or rain.
It won't rust and is safe.
Quantity needed:2pc. Against the Set
Quantity:1 Set of 4pcs.:2pc. The Set becomes a spare part.
It was a waste of time to find a usable part of the
I couldn't find anything.
Quantity:1 Set of 2pcs. products would also be available.
Thank you.
View detail
Black chrome？
It is Black chrome, but it is not so black as almost Chrome image.
If you ask me. Is it a little Black? That's about it
Cap bolt's inner hexagon with Exactly Uniqlo plating is transformed into a high-grade bolt
Don't make a mistake as it's not something you can put in the Screw hole! I made a mistake, W.
Is it a bit high? Maybe you could get 10 for 1,000 yen?
View detail
Ideal for covering up holes, but difficult to remove.
It is used for the screw hole of Plate which is exposed with footpeg position change. Because this is much cheaper than hiding with an ordinary Bolt, and the appearance seems to be good, I tried it.
The diameter of the head is almost the same as the screw hole and it is very neat. The protrusion on the side goes in easily in the inserting direction, and there is no need to worry about it coming off due to vibration as it is designed to catch on the screw thread in the pulling direction.
After that, the footpeg was finally installed in the same position as the original and this Cap was no longer needed, so I tried to remove it, but this time I had a problem. However, the Slotted screwdriver was not able to be put in at all because of the Smallness of the head diameter and the adhesiveness.
Fortunately, the hole I used is penetrating, so I was able to push it in with a driver and pull it out from the back. If the hole is non-Penetrating, you will need to drill a hole with a drill bit and cut it out with a cutter, etc.
Before you use it, you should really think about whether it's strong enough to cover it up and Large before you use it.
View detail
Perfect for blacking out
It is ideal for blacking out the car body
You can easily blind and blacken the Bolt
It is also heat resistant and safe
The price is a bit high
View detail
It could be a little cheaper
I've bought them many times to cover the head of One Point and Bolt
It would be great if you could make it a little easier or increase the number for the same price
It's a tighter fit than you might think, and it won't be gone before you know it
I sometimes buy them because of price adjustments
View detail
Durability is difficult
I bought a red one for a little dress-up, and it's very easy to put it on the Bolt It is
It's shiningly good and the color is very good, I think it looks very good, I'm trying to prevent it from deteriorating as much as possible When I wiped it with Plexus, the plating on the corners peeled off a bit
I felt it wasn't as durable as I thought it was going to be, and the price is so low that you have to replace it every time it deteriorates It is
And I want the number of entries to be even
View detail
Damn it!
I bought it for the Mirror Hole Cover and it is much smaller than I thought it would be
When I first saw it, I thought it was either the diameter of the hole or the Bolt cap, but it's smaller than the Image is
It went in the screw hole of the M10 tightly, but the spit? I have no complaints if the outer diameter of the
It's returned, so it doesn't look like it was left out at all
View detail
Bolt Cover 12mm
this item is well made and all but the gold color is like more orange than gold, however i like how it looks in my bike. regards! View detail
If you can choose some Design face White.
With complete Bolt On, it can be installed in 20 seconds ??. Just a few more if you can choose the same color as Design, it will be more determined, View detail
Focus on appearance
It is in use with the company NASA TypeHolder used for Number.
We are using similar products of other companies,
There is no thing that installation precision is high, abnormally installed is hard or loose.
Total likes it,
The outer shape is slightly small, so it is only a few but the part where Bolt's head is not hidden,
After all it is high w
View detail