Reviews
Hole plugging!
Regardless, it is just a Bonsai Parts to fill the Screw hole!
But, well, I wanted to add some Blue color to it, so I went out and spent it....
View detail
Bolt cover
Bolt, installed for protection purpose to the Nut.
It seems to be a little hard plastic and is hard to remove after installation.
Quantity:1 Set of 3pcs., the price is not that much and it will look a little better.
View detail
ScrewCover
The screws near the Exhaust System interfere with vibrations and cause scratches, so I bought this to try to protect and prevent scratches.
The colors are vibrant, not bad looking.
Quantity:1 Set of 3pcs., the installation seems to be a little stiff and difficult to remove.
View detail
2 while shopping
It's just self-satisfaction. I don't care if I don't have it.
It is a Dress-up that only those who ride the same Motorcycle will notice.
But isn't it good!
View detail
Bolt cap for motorcycle dress-up
Was the one you received as per Image?
It was just as Image.
[How did you feel about the Fit?
Some items are somewhat easy to remove from the Bolt, which may be due to differences in the Bolt's hexagon.
View detail
My impression changed.
I think Black's Case will have a sense of unity.
It's just a Rubber cap that costs over $100 per cap.
I think it's expensive
View detail
When was the last time you dropped out of a replenishment?
I bought these caps because the caps on my Handlebar Clamp Bolt had fallen off before I knew it, and the price is great for a pack of 12. View detail
It's just Rubber's Cover.
It's expensive for a mere Rubber's Cover.
But I think it is very effective because it is in view.
View detail
PetitCustom
PetitCustom Bolt Hole Cover for Handlebar Clamp. View detail
Shiningly glowing and looking great!
Gold color is beautiful!" and my neighbor's beautiful girl gal JK is very receptive lol!
Gold color seems to be accepted by gals… Riders who want to be accepted by gals, let's install it!
Recommendation!
View detail
It is good.
It is good. View detail
Z900RS SE
Some parts can be removed quickly and others can't. A little expensive. View detail
Fits: KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
To KICKless.
The Rear Sets and Kick pedal interfere with each other, so I removed the Kick pedal and installed this Cap.
I like it because it matches the overall Image of the vehicle.
It may not be suitable for a NORMAL-looking car body.
View detail
It's just a plastic Cap.
It's just a plastic cap, like the title says.
It is probably the same model as the one included in the HURRICANE Pipe Handlebar KIT in Black.
This time I used it on a Bolt that was dyed black on Stainless Steel, but it was too tight!
I accidentally got a Wound on the butt of a Penetrating Minus.
View detail
Bolt cover
Looks good to me.
But if you do one place, you might want to align other places too…
View detail
I wouldn't be surprised if you dropped it at any time.
This is another PetitDress- found at KITACO and ConvenienceParts upItems. upItems. it's totally dress-up, because for practical purposes I don't need this kind of Cap. However, I thought it was well made for that purpose. Anyway, the body is Material:It's aluminum and has been properly treated with anodized aluminum, so the color and The shine is good. Normally, the Bolt cover is made of soft plastic, but it is not made of aluminum. Since it is not deformed, the O-ring is inserted into the hexagonal hole of the Cap bolt with it. This is a good example. The part where the O-ring is properly fixed has a groove digging, and it takes a lot of time and effort to process it. I'm there, so I guess it's no wonder it's so expensive.
However, this O-ring is a tricky one. The one for the smallest M6 Screw has a very small O-ring. So it was Large strange for me to fit it in with my old eyes. And it's probably because of the airtightness of the O-ring. Sometimes it would fall off on its own after a few seconds of fitting. No matter how many times I pushed it in, it would fall in such a way that it would come off of itself. As I observed, it seems that the air between this Cover and the Bolt's hexagon hole is compressed and the force The O-ring seems to be pushed back in. That's how airtight the O-ring is. As I was TRYING, there was apparently a point where the air inside was released and the push back phenomenon was The Large threshold type makes it difficult to push in. I hit it with a plastic hammer and pushed it in (I may not be able to get it off later).
However, I felt that the risk of falling due to vibration while driving was Large. It is not at present, but I must be prepared to lose it. At that time, I have no choice but to buy the replacement parts and deal with it.
I used 4 bags this time, and the cost was about 3,500 yen. Well, it's a good cost-benefit ratio for a dress-up, isn't it, using Pinpoint I think you can be satisfied with it even if you don't have a lot of them. However, because I think that it is not strange when it disappears, I think that other custom parts purchase You might want to buy a spare while you're at it.
View detail
It is only looks
I closed the M6Screw hole that I do not use.
Garbageetc. Although it can prevent invasion, since it is Pura Cap, since water enters, water gathers inside when it gets wet, there is a possibility that it becomes easy to rust on the contrary.
There is not much need, but please to prevent Garbage clogging.
View detail
Quality has Rose
I attached it because the head of Bolt of Uniqlo plating color is noticeable when Pannier caseMount is attached.
Some things do not fit unless they have to be pushed strongly with your fingers "Scauper" And there was something felt lightly, I felt quality with Rose. It is an impression that it seems that it is just getting off by vibration.
400 yen is too expensive for the four pieces of Plastic like this!
View detail
Fits: HARLEY-DAVIDSON Sportster Family, HARLEY-DAVIDSON softail family, HARLEY-DAVIDSON dynamo delta, HARLEY-DAVIDSON Touring Family
At One Point
I installed it on the poster and can install easily, I think that it is quite good as One point but I feel better if the price is a bit cheaper. View detail
Since its former own car does not have a Cap in the HEXAGON Bolt which is fixing the Handlebar, either and was pleasing in Rust prevention of appearance and a Bolt hole using the black Cap, it was used also for GT1000 replaced (Plating type). On the Desi
Since its former own car does not have a Cap in the HEXAGON Bolt which is fixing the Handlebar, either and was pleasing in Rust prevention of appearance and a Bolt hole using the black Cap, it was used also for GT1000 replaced (Plating type).
On the Design of the circumference of a Handle, although the Plating type was used, if it cannot press down carefully at the time of attachment, a Plating will separate.
Since the number was mostly contained well, when several pieces went wrong, it was OK, but I considered that it was better to be businesslike with throwing away.
View detail