Reviews
To hide the hexagonal hole
Plating was peeling and falling apart, so the
Purchased to replace
It looks pretty shiny.
View detail
Bolt cover
Bolt, installed for protection purpose to the Nut.
It seems to be a little hard plastic and is hard to remove after installation.
Quantity:1 Set of 3pcs., the price is not that much and it will look a little better.
View detail
Bolt cover
It seems to be good for Screw head protection and One point dress-up.Quantity:1 Set of 3pcs., Plastic, slightly stiff.
Installation is fine, but when removing it, it almost cracks.
Lack if you force it off, the color will peel off.
The price is not that much, though, so I would just buy it again.
View detail
ScrewCover
The screws near the Exhaust System interfere with vibrations and cause scratches, so I bought this to try to protect and prevent scratches.
The colors are vibrant, not bad looking.
Quantity:1 Set of 3pcs., the installation seems to be a little stiff and difficult to remove.
View detail
2 while shopping
It's just self-satisfaction. I don't care if I don't have it.
It is a Dress-up that only those who ride the same Motorcycle will notice.
But isn't it good!
View detail
I think it's good
It is just a decoration, if you like.
There is no sense of discomfort as if it had been attached from the beginning.
It is completely self-satisfying because no one but the person himself notices it.
View detail
PetitCustom
PetitCustom Bolt Hole Cover for Handlebar Clamp. View detail
Shiningly glowing and looking great!
Gold color is beautiful!" and my neighbor's beautiful girl gal JK is very receptive lol!
Gold color seems to be accepted by gals… Riders who want to be accepted by gals, let's install it!
Recommendation!
View detail
It's cheap and can do dress-up, but …
Easily dress-up with no tools required! … but it fades quickly lol
I've had it for a few years… but it's cheap, so why not! LOL!
View detail
It can be easily customized by simply covering it.
This product can be easily customized by simply placing it over an existing bolt. It can be used to hide rusted screws or as a Simple Waterproof alternative! View detail
It's cheap and it looks good.
I used it to improve the appearance of the cap bolt around the handlebar.
As you can see in the picture, the color matches the Titaniumium color of Posh's NASA TypeCap cover.
It's useful because you can almost hide the Bolt with both of them.
Just one note on installation.
Material:There is a cut-off from the RUNNER 125 at Plastic, so make sure it is on the lower side, where it is less noticeable.
View detail
To prevent rust.
MirrorMounting Bolt tightening holes
There was a pool of water and Rust.
I bought a Cap!
There was one with and without a rubber at the end of the cap, but
The part to be used this time is the Bolt that attaches to the horizontal direction
So, is it Large sturdy without Rubber? I think so.
Does the size fit since it's a special bolt?
I was worried, but the Exactly/Fit
This way, there's no water pooling in the car wash or rain.
It won't rust and is safe.
Quantity needed:2pc. Against the Set
Quantity:1 Set of 4pcs.:2pc. The Set becomes a spare part.
It was a waste of time to find a usable part of the
I couldn't find anything.
Quantity:1 Set of 2pcs. products would also be available.
Thank you.
View detail
Black chrome?
It is Black chrome, but it is not so black as almost Chrome image.
If you ask me. Is it a little Black? That's about it
Cap bolt's inner hexagon with Exactly Uniqlo plating is transformed into a high-grade bolt
Don't make a mistake as it's not something you can put in the Screw hole! I made a mistake, W.
Is it a bit high? Maybe you could get 10 for 1,000 yen?
View detail
I wouldn't be surprised if you dropped it at any time.
This is another PetitDress- found at KITACO and ConvenienceParts upItems. upItems. it's totally dress-up, because for practical purposes I don't need this kind of Cap. However, I thought it was well made for that purpose. Anyway, the body is Material:It's aluminum and has been properly treated with anodized aluminum, so the color and The shine is good. Normally, the Bolt cover is made of soft plastic, but it is not made of aluminum. Since it is not deformed, the O-ring is inserted into the hexagonal hole of the Cap bolt with it. This is a good example. The part where the O-ring is properly fixed has a groove digging, and it takes a lot of time and effort to process it. I'm there, so I guess it's no wonder it's so expensive.
However, this O-ring is a tricky one. The one for the smallest M6 Screw has a very small O-ring. So it was Large strange for me to fit it in with my old eyes. And it's probably because of the airtightness of the O-ring. Sometimes it would fall off on its own after a few seconds of fitting. No matter how many times I pushed it in, it would fall in such a way that it would come off of itself. As I observed, it seems that the air between this Cover and the Bolt's hexagon hole is compressed and the force The O-ring seems to be pushed back in. That's how airtight the O-ring is. As I was TRYING, there was apparently a point where the air inside was released and the push back phenomenon was The Large threshold type makes it difficult to push in. I hit it with a plastic hammer and pushed it in (I may not be able to get it off later).
However, I felt that the risk of falling due to vibration while driving was Large. It is not at present, but I must be prepared to lose it. At that time, I have no choice but to buy the replacement parts and deal with it.
I used 4 bags this time, and the cost was about 3,500 yen. Well, it's a good cost-benefit ratio for a dress-up, isn't it, using Pinpoint I think you can be satisfied with it even if you don't have a lot of them. However, because I think that it is not strange when it disappears, I think that other custom parts purchase You might want to buy a spare while you're at it.
View detail
Luxury in a cheap Bolt
If you put this on, even a cheap Bolt will look luxurious If you care about the appearance, this is the recommendation for you
I was motivated by the crappy Bolt that came with the Over's exhaust system This was introduced
View detail
Durability is difficult
I bought a red one for a little dress-up, and it's very easy to put it on the Bolt It is
It's shiningly good and the color is very good, I think it looks very good, I'm trying to prevent it from deteriorating as much as possible When I wiped it with Plexus, the plating on the corners peeled off a bit
I felt it wasn't as durable as I thought it was going to be, and the price is so low that you have to replace it every time it deteriorates It is
And I want the number of entries to be even
View detail
Bolt Cover 12mm
this item is well made and all but the gold color is like more orange than gold, however i like how it looks in my bike. regards! View detail
In places you do not want to make it stand out...
A fashionable Bolt cover of DAYTONA and POSH is also good, but I like this kind of simple design in places where you do not want to make Cap bolt stand out.
I purchased the same Cap Bolt Cover last time, but I bought it as Stock.
Which Manufacturer should cost half price, or about 30%....
View detail
Quality has Rose
I attached it because the head of Bolt of Uniqlo plating color is noticeable when Pannier caseMount is attached.
Some things do not fit unless they have to be pushed strongly with your fingers "Scauper" And there was something felt lightly, I felt quality with Rose. It is an impression that it seems that it is just getting off by vibration.
400 yen is too expensive for the four pieces of Plastic like this!
View detail
Preliminary purchase.
Stock got lost, so I bought it. I think that it is more durable than the thing of the plaque, so this Bolt cover is all Material : I am wearing Aluminum stuff. When installing, RubberRing is hard and does not fit exactly, so I attach a little Silicon grease. View detail