Reviews
Waterproof property is not good
I bought this for Repair because the original Fender Eliminator License Plate Light was damaged. The light shines well and the visibility is good, but the waterproof property is not so good… Large rainfall causes water to get in… For now, I use it with Duct Tape wrapped around it, but I think it would be better to use it for a long time by coking etc. View detail
LED License Plate Lamp was broken.
[How is it used?
The LED License Plate Lamp that came with Active's Fender Eliminator Kit was cracked, so I replaced it.
License Plate LightSince the price is almost the same as the Single Body one, I bought this one.
Was the installation difficult?
If you can do wiring, it's easy, but if you don't have the tools, it's not so easy.
How was your experience with it?
The black resin on the outside of the License Plate Light is so thin that it easily cracks when tightened even a little too hard. It is too thin, so I wish they had made it a little thicker or made it from gold.
[Included Parts:were they on?
Sticker、with Clip
[Opinions and requests to Manufacturer
I don't understand why License Plate LightSingle Body and License Plate with Bracket are almost the same price.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON Touring , HARLEY-DAVIDSON Softail , HARLEY-DAVIDSON Dyna , HARLEY-DAVIDSON Sportster , HARLEY-DAVIDSON V-ROD
It's an anti-theft license plate light!
[How is it used?
I somehow added a position lamp to Blinker and Headlight, so I wanted one in the back as well. So I bought one for the back.
Was the one you received as per Image?
Yes
Was the installation difficult?
The handling of Wiring was Large strange.
How was your experience with it?
It is good at night with a faint glow, but during the day it is hard to tell.
Anti-theft effect cannot be expected because even though the front Nut is special, it is easy to loosen a regular Nut from the back.
[Included Parts:were they on?
Nut only
[Was there anything that disappointed you?
Wiring is longer than expected and gets in the way.
▼These are the Parts that cannot be Recommendation in terms of cost-effectiveness.
View detail
Well, I guess this is how it is.
I had replaced it with R&G's Fender Eliminator Kit as soon as I bought the new car, and the Tail Lamp in the Kit was a transparent Lens, so it illuminated the Number to a certain extent. I am ashamed to say that I have never noticed this because I don't drive at night very often. When it was time for inspection, I took the car to the shop and found that Kit's Tail Lamp did not contain a License Plate Light! It turned out to be a good thing. I had always assumed that it was embedded in the underside of the Tail Lamp. I could have returned it to OEM, but that would have been too much trouble. So I looked for a reasonable License Plate Light, and chose this product with License Plate Bracket due to the problem of securing space for installation. Since my car inspection was coming up, I had it shipped directly to a Motorcycle shop and they installed it immediately.:2pc. No Set light! Clearly insufficient light intensity. Requested immediate return and exchange and completed the exchange and installation the next day. This time, all 4 lights came on and the luminous intensity was sufficient. I was able to meet the scheduled vehicle inspection date with the limit.
The license plate bracket is the smallest necessary size and thickness. The License Plate LightBody also has good brightness, but the wiring comes out from the side, so it is impossible to keep it out of sight. I would not recommend it to those who are particular about the details of the appearance of the light.
I think it is a product that is appropriate for the price. If you want a clean and high quality custom look, you should choose another product, even if it is more expensive.
View detail
I think I can handle the car inspection.
I installed them because I chose the Fender Eliminator Spec. The installation is possible to fix by Bolt&Nut and the brightness is bright enough, so I think it will pass the inspection without any problem. The power supply can be removed from the tail lamp and it is easy to install. View detail
If you can process it yourself, that's good.
Quantity:I'm thankful that I was able to buy it for less than $1,000 for 1 Set of 2pcs. but it's only cheap. The sea-ring is not done properly and I did the sea-ring by myself using the Glue gun. Although the important LED is bright, it sometimes flickers by Idling, probably because of the relation of the voltage of Battery. It seems to be possible to make it to the position light etc. according to Ideas. View detail
Compact
Because the vehicle has changed, again repurchase.
It is easy to solve the License Plate Light problem in making it a Fender Eliminator.
Basically I only ride during the daytime, but the one I'm in trouble is License Plate Light.
I attached a separate formula, but I am not good enough.
Eventually I came back to this License Plate Bolt Type.
Again the appearance is clear.
After all, a little more light itself is wanted to spread.
View detail
Material : I wanted Aluminum.
Holder of LED light is Material : I think that the texture was better if Aluminum.
For this price Plastic felt high.
Other Manufacturer goods at this price Material : I am disappointed to know later that you have Aluminum
View detail
I could not adapt to my body
【What made you decide the purchase?】 Required item
I was looking for License Plate Light and I was looking for a small one.
Also, since the light irradiation width of the LED was a wide angle type, purchase.
【How was it actually used?】 Required item
Rear Fender is quite diagonal on my car body, so when I installed it, apparently I could see the light source and decided that I could not clear the car inspection.
However, since the light emitting part can be bent to some extent by hand, you can adjust the angle.
【Was it difficult to install? (Hard parts case)】 Any item
Installation on the car body is only to interrupt the License Plate Bolt, but we are using LEDs and we have to wire with the car body.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Any item
Wiring please go definitely.
If you bend with too much hands, because it is a thin iron plate it will cause Gold genus fatigue and break.
[Is there anything I was disappointed about?] Required item
It was that I could not conform to my body.
There is no problem with the product.
【Hope for Manufacturer - Please let me know if there are any improvement points] Required item
It is a type that pastes the LED to Bracket, but I think that it will peel off someday. Is it better to change to Bolt Tightening Type for Bracket?
【Have you compared items?】
There will. It is another part of DAYTONA
View detail
Fairly
I purchased Number to relocate to SIDE. Although I think that there is enough brightness, the transparent resin of the LED part is a little cheesy, but there is no problem because it does not look quite like in the vicinity, so there is no problem. I am satisfied because the price is also Reasonable. View detail
Since it was the lowest price with the LED Bolt, it purchases.It uses as Number light.Although the stand of a Stay and a passive reflector, a Number frame, and a Number plate will be collectively stopped in the case of attachment, a place [ t
Since it was the lowest price with the LED Bolt, it purchases.It uses as
Number light.Although the stand of a Stay and a passive reflector, a Number frame, and a Number plate will be collectively stopped in the case of
attachment, a place [ the effective thread part called it the Limit ].Since
construction material is not iron, either, intensity is anxious.It is anxious although he thinks that water proof can be expected to some extent as transparent resin is [ portion of
LED ] contained.As [ be / since it was
LED and became a local way of illuminating, it had estimated that light probably did not fly back directly, but / it / a diffusion Type ] ... A luminous source's appearing and indication are likely to be received depending on the angle of the
Number plate.As [ shine / the Number itself / in the distance of
however this LED, and a Plate / seldom ] ...
-- or [ that there are indication by an automobile inspection and control indication since it is a Level which can say for the time being there is Number light ].Calling it , it goes by this until it breaks.
View detail
D trucker ('98) was equipped. Since wiring was not turned on as for which combination at first, it got impatient, but the light was switched on when twisting around the plug instead of an attached connection connector directly. (How to use a conne
D trucker ('98) was equipped.
Since wiring was not turned on as for which combination at first, it got impatient, but the light was switched on when twisting around the plug instead of an attached connection connector directly.
(How to use a connection connector is wrong ?) A rubber was not penetrated, although it inserted by the connection connector since it was a thin line like a goods photograph.
He made the hole in wiring of a car body earnestly by favor.
It is better to take care in the case of smile attachment.
important brightness and appearance -- being nice .
I think that it is very well conspicuous since it is bright.
View detail