Reviews
It was too difficult for me.
I had experience pasting automotive film in the past, so I bought it thinking it would work, but it turned out to be disastrous.
The shape is complex and cannot be aligned well with subtle curved surfaces at all.
Moreover, it is difficult to remove air bubbles because of the thickness of the ??Film, and it is stretched so much that air bubbles do not come out at all.
It is wiser to be honest and ask the PRO to do this.
Sorry, this is a bit of a whiney impresario. Yes, the product is solid and looks good.
View detail
A4 Size is good.
Size is A4, so it is easy to handle.
The fact that it is not in a volume is good because it can be handled without Habit being attached.
View detail
cut out and use
Cut out and affix to the area of interest in Motorcycle. View detail
scratch-resistant
I will put it on the area where it rubs. I hope it will be effective. View detail
Good
I bought a new Motorcycle and bought this to prevent Tank from getting scratched.
It was a little difficult to cut when cutting with Scissors, but I was able to attach it successfully.
It is difficult to completely remove air bubbles, but I didn't mind because it prevents scratching. The size is smaller than I expected and the price is a little high, but I am satisfied with it.
View detail
The shape doesn't fit.
The shape does not fit.
It looks like it, but no matter how you do it, the shape doesn't fit.
Therefore, dust accumulates there because some edges do not adhere closely to each other.
And it peels off from there.
Anyway, the shape doesn't fit.
View detail
There is also some gripe feeling.
Recently, SmallWound has become prominent on Tank!
I told myself not to worry about it because it was a training machine and I used it heavily, but I found an outlet product and stuck it on for prevention& protection.
The result was a Large success. The cut was quite precise, and by carefully removing air bubbles while adjusting the cut, I was able to achieve a generally clean finish.
Although it is not a GripType, it seems to have a non-slip effect and has some grippy feeling.
The work is to clean the surface thoroughly with Seat for removing oil from the attached kit, and then apply a liquid detergent diluted in the same way as for WindowFilm. (Container is also included.) Spray generously on the paste surface and Film and adjust the position.
The included spatula for pasting is just the right size and easy to use, but it seems to have two sides, so if you make a mistake, a wound will remain as shown in the image. (It is hard to see due to the reflection.)
Because of the complex shape of Z, we divided it into parts and removed air bubbles from the center outward.
To be sure, I left it for a day after the water dried to check the adhesion and took it for a test drive. There were no parts that were about to peel off, and the adhesion was firm, so there was probably no need to worry.
If it can be applied neatly, it will look good, and even slippery materials such as synthetic fibers can be used to hold the tank in place. (Not compared to GripType...)
The instruction manual is not included in the package, so please check the manual before preparation, and be prepared to work carefully and sparingly.
View detail
Fit for purpose
I chose the clear film despite being put on a black tank. The manufacturer claims the pads will take on a slight blue colour against black background.. but it's not really noticeable for me. It did take a bit of effort to push the majority of air bubbles out during installation. The colour block on the tank is still nicely visible, so that's a bonus. Make sure you know where your knees tend to sit & move on the tank before fitting the pads & allow this to guide your fitting location on the tank. View detail
There is no correct way to cut.
I bought a second one and tried many different Cutters, but Scissors
I found it to be the best. If you are dexterous, you can use Cutter, Cut
I am clumsy, so I made a protective film for the SeatBack with a commercially available product. It is better to have a paper pattern, though.
View detail
It was 3M.
I bought this film to protect the SeatBack of my CBR1000RR-R. Unlike the OEM film, it is easy to cut and good for cowl.
Hard to blend in and become Wrinkle.
View detail
I love using it. Definitely a great product that I can recommend.
I have been using it since my previous Motorcycle, and now I have changed to a new one. The purpose is to prevent rubbing when using Side Back.
I think it used to be thicker Seat.... My memory is a little fuzzy.
It was much easier to use because it was thinner in my hand than I remembered.
The description of the product is Strong adhesion but it's not like it won't come off once it's attached. "Detachable." This is a Type that can be used to
By the way, the reverse side can be recovered to some extent by washing it with a neutral detergent.
Rather, it is this ability to attach and detach The best." and can be detached when needed and when not.
When I didn't need it, for example, I would stick it on the door of my Shoes box or on a smooth surface.
The use is pretty much infinite Large, as shown in the second image.
Seat itself is not very elastic, so three-dimensional curved surfaces should be viewed as almost impossible. It is necessary to devise a way, such as giving up on a clean installation or making a good cut to let it escape.
It contains 3 sheets of 30×25cm, so it is about 3 sheets of A4 size. So, I think you can keep 2 sheets as a spare if you have a certain level of anti-scratch level.
I think it is OK to replace them more and more as they gradually become yellowish due to ultraviolet rays.
OneQuantity for TouringRider:You will not lose anything by purchasing Set! No regrets! Treat before the scratches show the substrate!
View detail
Film." Or rather Seal." impression
Since it is labeled "Film," I thought it was supposed to be applied with water, but it is a type that can be cut and applied as is.
Personally, that kind of thing was Image of Seal, not Film.
Because it is not designed to be applied with water, it is difficult for amateurs to apply it to a large area or complicated shape or part without air contamination.
I tried applying the film with water, but it was very difficult to push water out of the film due to the nature of the film, which is not designed to do so (the water stuck in the middle of the film).
Perhaps it is a product that is supposed to be applied to flat surfaces with a pinpoint large size.
View detail
Fits: SUZUKI GSX-S 1000 GT
It's better than nothing.
【It was good point】
The included Spray liquid (neutral detergent?) for water pasting is slippery and makes it easy to apply Film. The included Spray liquid (neutral detergent?) is slippery and makes it easy to apply the film.
To some extent, it is trackable, so some phases can be cleared without difficulty.
If you have basic knowledge of film pasting, even an amateur can work with no problem.
Also, some people said it was impossible with the included Squeegee, but I had no problem at all. It is rather small and easy to use.
Maybe you used Squeegee instead of misting over Film?
Complaints
I wondered if I could do the headlight and blinker parts (if I made the pattern myself) with the extra white space left over. I thought I could do the headlight and blinker parts (if I made my own pattern paper) with the excess White part, but there was no excess because they were completely hollowed out and pasted on the base paper.
In other words, there is no spare or even Repair material.
LargeQuantity:It is troublesome when working because everything is put together on a 1 pc. base paper.
Unfriendly, with no explanation of sticking position or orientation (no information beyond a picture of the number in the product description)
The accompanying Spray container for water application was shoddy and broke after less than half a year of use, rendering it unusable.
I had expected that the Film Cover range and size were precisely measured and cut by 3D scanning, etc., but the edges are slightly too much or not enough.
Also, some areas do not Cover the entire surface in the first place (photo attached), which looks bad.
"Wherever you need it (the part you want to put it on), make it look good." not The mount is this Size, so we can provide as much as we can within that range." I felt that this was the standard when I looked at the shape of the Film and the scope of the pasting.
【Review】
At nearly $30,000, this is a delicate price.
If you ask a pro shop for film installation, the cost of a full cowl will be 100,000 yen or more, so this is the best choice. Patience. However, I think it is more cost-effective to ask a pro shop to do it for NAKED.
[Ad Vise to the buyer.
You might want to buy a cosmetic Spray bottle at 100s before you work on it (because it will break).
It may be useful to have something like a precision nipper for plastic models to cut the excess that sticks out (it is hard to cut with Cutter).
Translation (please enter here) There is no manual (the amount of text is not a problem if you use machine translation).
View detail
High grip tires scatter stones.
CBR1000RR-R stepping stones as Cowl goes Wound
I put this product on it. It was Large strange to mold it.
I struggled. I managed to put it up, but my clumsiness made it difficult.
It suffered and looked considerably worse.
Large areas were better to be put up in sections.
The Curve surface was also watered with a misting spray, but Beauty
Cannot be done. Areas with a small area are finished well.
I did.
View detail
It's like Film on your phone.
It's similar to PelePera's Universal TaBrettFilm, which you can buy at the 100 yen Shop. This would only cost 200 yen. I think you should check carefully before you buy it. View detail
For Tank Protection
I put it on the perimeter surfaces of Tank and Seat.
This is to prevent the paint from peeling off the tank as the Seat rubs against the tank after a long ride.
Apply diluted soapy water on the Tank before applying it to prevent wrinkling.
View detail
Before you damage your new car…
The New Model CROSSCUB110 that I had ordered was finally delivered the other day. I immediately read the various impressions of the senior CUB owners and found that the main pipeCenter cover is easily damaged by foot contact when riding, so I purchased this film to protect my feet while the car is still new. I bought this film to protect my feet while the car was new. Once I removed the main pipeCenter cover, I cut the film to fit the shape, and put it back on the body again. The rest of the cut film was used for the area I wanted to cover on the side of the center cover. View detail
Some modifications required for ZX-10R 2021~.
The dimensions are not correct and several pieces need to be machined.
Especially the Front mask part is not at all, and it makes almost no sense to buy it.
The above is true even if you want to use this product at a lower cost because of the high cost of hiring a specialized contractor.
It is better to ask the contractor from the end.
However, since the ZX-10R 2021 product was not good, the quality of the other models' products is unknown.
View detail
taut
I was looking for something that wouldn't ruin the design of the Tank and I found this. I was looking for something that would not spoil the design of the tank and I found this. View detail
Is good
It is affixed where the Fuel Tank and Seat interfere with each other.
[Color] The tape is clear and transparent, so it is not noticeable and protects the painted surface.
Seal is easy to apply to curved surfaces and effective in preventing scratches.
View detail