Reviews
Aluminum spacer
There are several patterns, colors and shapes to choose from
Other Brand ProductScreen's off-color plastic washer Exchange from
The head of the torque is changed to a thin type, and washer is used here The custom feel goes up
Since it also expands the contact area, it may be effective in preventing cracking
View detail
Fine tuning
CBR400RR (NC29) I used it to fill the Carburetor setting in the I wanted to get rid of it, but I wanted to use the Fixed Type So I put this product in between the two I'm happy with the valleys that have been eliminated View detail
DRCAluminum spacer
This Type:11 has the reverse side instead of the Flat
Because of the steps
When there is a large hole in the bolt compared to the M6 Bolt, or
Fine-tuning when a Bolt is a bit too long, or
When you want to float a little bit, etc
It is convenient to use at a moment's notice
View detail
Protect the Cowl paint and seal
When you tighten the Screw, the paint and seal on the surface of the Cowl will come off, but it can be removed It's the only thing that can prevent it And I installed it There seems to be quite an effect, and I can fasten Screw with peace of mind
I want it to be a little thinner You can feel that you are wearing it a lot
View detail
Used for CRF250L coolant drain bolt
I could have ordered the Honda OEM parts from them
I found this product when I looked for it by part number, so I bought this one
Slightly cheaper than ordering and buying OEM Parts
The name of the product is OilCheckBolt, but
The CRF250L's coolant drain bolt is the same size
It can also be used here
View detail
Setting stuffing
This is an impression of the CBR400RR (NC29), which is a four-cylinder engine Quantity:You will need 4 sets
Jet needles used in OEM negative pressure carburetor are often used in the Clip You can't change the position, but you can take it in the darker direction with this Shim There are two different thicknesses, and although the difference is only 0.2mm, I could certainly feel the change
When I measured the air/fuel ratio in ChassisDynamo, the middle range was a little thin, so I was able to get a better idea of what to expect I tried it, but the improvement of the torque feeling and the fall of rotation when blowing is Smooth It has definitely changed in a darker direction At the same time, the Response has been slightly dulled Since we are currently changing the setting near 10m above sea level, we are now in the summer and at higher elevations It's a good idea to make it too dense when considering Touring, but Needle Jet's You don't have to take off the carburetor to change the shims You can feel the difference in the driving experience with just a few simple setting changes It's part of the fun of Carburetor Vehicles, so you can touch it and see how it works I am satisfied with the results
Cost performance is so-so, but the Needle Jet is not I haven't had any problems with it being hard to get into the holder or the core being gapped I am relieved to be able to use it without any problems
View detail
Versatile Custom for Everywhere
Off-road&MOTARD at Absolute CustomManufacturer Anodized, sticking to aluminum spacer, solid and colorfast The treatment is done, and it is possible to customize in the areas that are lacking I'm very happy with it View detail
Buy more washer that was missing
I replaced all the engine bolts of MT09 with Red of Aluminum Bolt
I replaced the Kit first, but there was a missing part, so I replaced the Washer with the Quantity:I bought 2 more sets
Large Satisfied
View detail
PetitDress-up
I bought Red to match the body color of MT09
I've replaced all the Right Side with Red Bolts, but I haven't had the Left Side yet Next, we will replace the Left Side
I'll post more pictures when I receive them
View detail
Self-satisfaction is on the rise
What made you decide to buy?
Parenthesis MyGROM casually and yet parenthesis well! I guess it's all about self-satisfaction enhancement
How was your experience with it?
The M6Aluminum taper bolts were also used in combination with the company's M6Aluminum taper bolts to install the parts It was It looks better too Also, as others have reviewed, I wonder how well Anodized can keep it up! It is
Was the installation difficult?
Easy to install! You don't need a special tool...but if the bolt to be co-tightened is special, the tooling is special too! I think it will be a Tool
View detail
Fits: HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100, YAMAHA Scooter type 50, YAMAHA Scooter type 90, HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100
Adjustment Required
YamahaJOG Z2, Honda LiveDIO-ZX, SEA BASSADDRESS V I was able to use it for 100
It may vary depending on the year, etc., so please check with yourself
This is a must for secondaries that have enough room to drop into the Belt You can increase the maximum speed without changing the start dash, depending on the settings
The parts system is not perfect, so it may need to be shaped by File or other means There are some people who say that the gold amount is high, but this size and shape may need to be special-ordered I think it's a reasonable Gold amount because you can't get it without it
View detail
That would come in handy
There is no BALI on the cut surface and the dimensions are not loose and the quality is good
Cowl, Axle Nut, etc. are versatile and inexpensive to use, so if you have them in your toolbox, you can use them
It's very convenient
View detail
Fits: SUZUKI Sky Wave 650, SUZUKI glass tracker, SUZUKI Glass Tracker Big Boy, SUZUKI Glass Tracker Big Boy Fl, SUZUKI Glass Tracker Fl, SUZUKI Wolf 125, SUZUKI SV650, SUZUKI SV650 S, SUZUKI ST250, SUZUKI ST250(Fl vehicle), SUZUKI ST250 E, SUZUKI RG500 "., SUZUKI RG400 "., SUZUKI RG125 "., SUZUKI RA125, SUZUKI GSX400L, SUZUKI GSX400E Katana, SUZUKI GSX1300R Hayabusa, SUZUKI GSX1100S Katana, SUZUKI GS750 GL
Does not fit TU250 grasstracker
Too large to fit the TU250 grasstracker engine. It does not fit inside the "seat" in the engine which the exhaust manifold fits into. I did not try on other bikes. View detail
It's cheap on the web
AddressV125GK7 Oil drain bolt for gasket
M10× 18.5mm (19mm on ManufacturerSite) purchased
I've used it many times and there are no oil leaks, etc
The cost performance is the best, with a little over $20.00 per piece of gold
I think it's perfect for those who ride GunGun and change oil by themselves
View detail
Fits: SUZUKI ADDRESS V125
In my vehicle
It's only 0.5mm, but when you install it on your car
Because the OEMDrive face comes outward, it will hit the Case just a little bit and
I heard a sound of rubbing with the Case
With an external Face, it may not be a problem
Since it is very small, I think there are some individual differences between vehicles, so even if it is 0.5mm, the vehicle can be installed with no problem I think there is also
In my vehicle, 0.3mm was the limit
View detail
Fits: SUZUKI ADDRESS V125
To adjust the drive train
0.3mm Washer
I installed it to emphasize acceleration
It's only 0.3mm, but it worked
The top speed was lowered for that
I'd really like to get a narrower Belt
The V125 Belts are thicker than any Manufacturer's Belt
View detail
Different sizes
I went out of my way to buy a 2mm thick product and all the ones I received were Thickness:It was 1mm
Why is this happening?
Very disappointing
View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4)
I'm making a double layer
I bought it when I was OHing my Carburetor, and like the OEM, the thickness of the Washer Because of the thinness of the material, it will inevitably become distorted over time
So I installed it in two layers and it did not distort
View detail
Consumables to be replaced at every oil change
What made you decide to buy? Affordable and cheaper than OEMs
How was your experience with it? No oil leaks
Was it difficult to install? (In the case of hard parts) Drain bolt, Quantity:Just Set
What is the point or hang of installation (for hard parts)? Any
How does it feel when you wear it and what is your height, weight, etc. (in the case of Apparel)? Any
[Was there anything that disappointed you? None
Do you have any wishes or improvements you would like to make for the Manufacturer? None
[Do you have any products to compare it to? OEM Parts
[Others] I removed the drain bolt to change the gear oil, but the washer was on I don't have one It looks like I forgot to put it on the last time I replaced it Still, did the Oil not leak? It's a relief to have it
View detail
It's better to have it where vibration is a concern
brembo [Color] When the specs were changed to Smoke's Reserve Tank, the mounting holes are large There are no bolts that will fit as is It seems to assume Rubber
So I bought the same product that fits the hole diameter
I think it's good because it fits well and absorbs vibration well
However, you will need to periodically retighten the Bolt as it is tightened through the Rubber
View detail