Reviews
The quality is good
It is polite making without cutting marks. Just a small hole is not easy to clean because dirt collects with Off cars, so I'd like a different design. After that DRC made Red alumite is fearing that it fades as fast as Zeta, so it's worried.
Like Brake hose I am doing Accent with Red and Blue. Because I made Sprocket Large in RMX, changing the position of Guide changed the position of Bolt in Swingarm, so it was hidden.
It's good for a little Accent as it's not expensive.
Just with a shoulder stick and nothing or an Iloilo type so as not to make a mistake.
View detail
I am saved.
I need to find the Size that I would like to be a mass merchandiser from the shelf, but I am very saved because we can choose from Wet Big..
Of course, the quality of the product itself is no problem and it can be used for free shipping price adjustment so it is saved Large w
View detail
It can be used for subtle setting in the middle range!
Restoring the old 2-Stoke 1995 formula Aprilia RS125 and doing Carburetor setting.
I started to narrow the main jet, but there are Torque valleys at 5000 rpm and 7000 rpm. Especially 5000 rpm is worse. When using the number of revolutions around here, the Axel opening degree is about 50%.
Setting of Axel opening degree is done with Jet needle. I switched the number of clips before from the top to the 3rd step ⇒ the 2nd step I felt the valley of Torque stopped.
If we go further and move to the first row it becomes thin, but even if it becomes too thin it is scary so I bought this KITACO's Needle SIMM set.
This Set has 0. 3 mm and 0. There is a 6 mm Shim one by one. Set the number of Clip stages to the first level, and 0. When 3 mm shim is inserted, exactly 1. It became equivalent to 5 steps.
With the trial run by this, the valley of Torque has further broken down.
After confirming the burning of the Plug, then remove the Shim and turn it further into the first stage - The tightness at medium openness has improved. Even if you are running through the streets, you can run comfortably because the connection has improved from bottom to top.
As a result, I removed Shim, but I thought that it was a very good Parts. In the future, Shim's likely to come in when the temperature goes down.
View detail
Satisfaction !!
I own an off-road racer and I bought it because Oil exchange frequency is high.
Although it may be an arbitrary, since it is Aluminum, please do not use it other than the low Motorcycle of tightening Torque.
I am very satisfied with this product.
View detail
Stand out from Aluminum
I used it for Caliper's OH. Somehow I thought that copper was more beautiful? Although I chose this, by chance I felt like I could match with Fitting's Orange. Sorry a bit because I can not see it. View detail
Small boss Spec. Challenge to!
Thick boss → narrow boss Spec. I thought about changing, KITACO 0. We bought 5 mm Washer, OEM fine boss & Washer at the same time.
Why? KITACO 0. 3mm Washer had (I might have purchased it by mistake before)
Wait, things are fine boss Spec. And Taiho Boss Spec. I would like to enjoy setting carefully which is better.
View detail
Accuracy is sufficient, but I want you to increase Size
I used it for processing Torque Camshaft.
I think whether it is a product with no effect unless it is processed.
Specifically, Belven on the Driven side (Wheel side) It is used for increasing the dropout of the product, but I would like you to increase the Size a bit more.
(1. 0 mm, 1. 25 mm and so on)
It costs a little, but I think that those who aim for the highest speed are necessary items.
View detail
Soft copper
【What made you decide the purchase?】
I purchased CoolantDrain bolt as Gasket.
You can use OEMParts' Gasket, but since it was the same Size, I bought this.
【How was it actually used?】
From the OEM Gasket, when I tightened Bolt, I felt like I would cap it exactly. Is the copper made soft?
I thought so..
[Is there anything I was disappointed about?]
There is none.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Not at all.
【Have you compared items?】
I compared it with OEM Gasket, but I thought that this was better.
View detail
Along with Bolt exchange of M5 Size
I wanted the same color Spring washer at the time of replacing the hexagonal hole Bolt of Black Painting at the same time, but at the Motorcycle Parts specialty shop in the neighborhood where I live and the home center there is no treatment and purchase items here.
Although it is a very common Spring washer, the number of entries is also Quantity : 2pc. I am satisfied because it was the number I wanted personally in Set.
However ... if you can only say it, the price feels a little expensive ...
But since each BoltWasher's Lineup is also abundant, we can not find anything of Large resistance unless it is of special shape!
I still need Bolt classes, so I would like to continue using this Manufacturer's thing in the future!
View detail
Fits: YAMAHA JOG50 series, YAMAHA JOG50, YAMAHA JOG50, YAMAHA BWS-R, YAMAHA CYGNUS X, YAMAHA BWS100, YAMAHA BWS125, YAMAHA GRAND AXIS 100, YAMAHA AXIS 90, YAMAHA JOG90, YAMAHA Axis Treat
Acceleration performance improvement!
SE44Japanese specification mounted on CYGNUS X.
Because NORMAL was too bad acceleration and dissatisfaction explosion, I bought and installed it with reference to everyone's impression!
This time, 9. We purchased at the same time with 5g Weight Roller and only tried Roller, Shim washer and so on, but as a result 9. 5 g Roller and OEMShim 0. 35 and this item 1 mm total 1. Calm down at 35 mm!
When it is NORMAL, the acceleration performance has been significantly upgraded and it became very easy to get on!
However, it is only about 700 yen It is accelerating so fast Because FOR JAPAN MODELCYGNUS has transformed, greed has emerged, the following is studying Torque Camshaft, Sense Player and Clutch Spring.
With less expense, I want a change in acceleration performance, and for a setting it is a very good product.
View detail
ACTIVEActive Washer
I exchanged when I changed around Brake.
I think that it is a non-reusable part.
There is a kind of thickness of Gasket, so you can adjust the length of Banjo bolt.
View detail
Unified consumables
I do not want to reuse Brake line so I will exchange it for a new item.
Hose and Banjo together in the same Manufacturer.
Although it is a problem of feelings, is not it a good sense of unity.
View detail
JPMoto Mart (Dura Bolt) Rubber Washer
JPMoto Mart (Dura Bolt) Rubber Washer
I purchased a new Screen, so I bought it
OEM is Material : Plastic White's Washer So Material : I tried buying it for trial, how about Rubber products.
Because it seems to absorb vibration, Creak sound disappears and it is satisfactory.
View detail
It's valuable!
I bought it for installing Stand Hook Bracket. It is for scratch prevention when attaching to Swingarm, it can be used without problem without loosening, I used it also for the clearance adjustment of Carbon fender with the difference of Size before, but it is saved by Large funny convenience goods.
View detail
Reservoir for Ninja H2 Tank used for diversion
I bought Nisshin Rapon for installing Ninja H2's reservoir tank.
【What made you decide the purchase?】
I saw an article diverting Ninja H2's reservoir Tank to Nisshin's Master cylinder in a certain blog, so I bought this product according to that blog.
【How was it actually used?】
Because it has Rubber in between, it is hard to be affected by vibration, and fixing is also done with chitin so you can run with confidence.
【Mounting was difficult?】
I pulled out the Gold Genus Color which is attached to the Rubber and fixed it to the reservoir Tank.
In my case I wore it with bare hands, but if I feel stiff, Slotted screwdriveretc. Please push it with the tool of.
【Please tell me the installation point and hang】
When inserting the Rubber using the tool, I think that it is good to curing and not to hurt the Parts and the car body wearing the Rubber or to adjust the power.
[Is there anything I was disappointed about?]
None
【Hope for Manufacturer - Please let me know if you have any improvement points]
Quantity : 1 Set of 2pcs. It is sold at, but this time I used 1pc. It was only.
Because it becomes expensive if set, 1pc. I thought it would be saved if I sold it with Single Item.
【Have you compared items?】
None
[Others]
In my case I used it to fix reservoir tank, for example Cowletc. It is also possible to use the H Type Rubber for protection of Wiring even when opening a hole in Wiring.
1pc. I thought it would be better if the selling price or price was a little cheaper.
View detail
Copper WasherGasket
【What made you decide the purchase?】
I thought about purchasing OEM 's Copper WasherGasket, but when purchasing an OEM, I ordered only in units of 10 pieces, so I bought this one that I can purchase from one piece.
【How was it actually used?】
Like OEM, it worked firmly
[Is there anything I was disappointed about?]
There is none.
【Hope for Manufacturer - Please let me know if you have any improvement points]
There is none.
【Have you compared items?】
There will.
View detail
Ordinary Copper Washer
It's an ordinary Copper WasherGasket. It is used for the Gasket around the Engine. 1pc. It is appreciated because you can purchase from. Because you can buy it cheaply, you can use the new Gasket at every exchange. View detail
Purchase
I went to look for Spring washer of Stainless Steel of this for M10 at the neighborhood Motorcycle Supplies Store but I bought from Bolt and Set things or iron Spring washer only from this place. KITACOConvenienceParts is rich in variety and it is saved. View detail
It is a spare purchase..
I bought Stridgeless hose of Goodridge, but the attached Crash washer is Material : I bought a Crash washer of copper as it was Aluminum.
Aluminum may be good, but we are looking for durability that copper is preferred.
Also, because the price is also cheap and reliable Brand it can be Recommendation.
View detail
Purchase
In the neighborhood mass merchandisers we purchased this size without Stainless Steel Plain Washer of this size. It is also helpful to choose the thickness. I am satisfied with both price and delivery date. View detail