Reviews
Fits: HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100, YAMAHA Scooter type 50, YAMAHA Scooter type 90, HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100
Adjustment Required
YamahaJOG Z2, Honda LiveDIO-ZX, SEA BASSADDRESS V I was able to use it for 100
It may vary depending on the year, etc., so please check with yourself
This is a must for secondaries that have enough room to drop into the Belt You can increase the maximum speed without changing the start dash, depending on the settings
The parts system is not perfect, so it may need to be shaped by File or other means There are some people who say that the gold amount is high, but this size and shape may need to be special-ordered I think it's a reasonable Gold amount because you can't get it without it
View detail
Fits: HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100, YAMAHA Scooter type 50, YAMAHA Scooter type 90, HONDA 50 Scooter type 100, HONDA 50 Scooter type 50, HONDA 50 Scooter type 90, HONDA Dio system in general, SUZUKI zzz, SUZUKI Address V100, SUZUKI address V125, YAMAHA JOG system in general, YAMAHA Scooter type 100
It's for Motorcycle that ups horsepower and Torque!
Even if it is used for Normal engine Motorcycle, it will become high gear and acceleration will fall.
Please install after power up with carburetor or Exhaust System.
Certainly the performance goes up, but the price seems to be too expensive.
* This product is 3 mm thick 03 - CW, but 5 mm thick 05 - CW should be considered for Bore up.
View detail
Accuracy is sufficient, but I want you to increase Size
I used it for processing Torque Camshaft.
I think whether it is a product with no effect unless it is processed.
Specifically, Belven on the Driven side (Wheel side) It is used for increasing the dropout of the product, but I would like you to increase the Size a bit more.
(1. 0 mm, 1. 25 mm and so on)
It costs a little, but I think that those who aim for the highest speed are necessary items.
View detail
Value understood to those who understand
Scooter's secondary Sieve, so-called Torque Camshaft, is usually designed to interfere with Clutch and not open to the maximum Large.
For Scooter, the thicker Belt width makes the best use of Drive pulley 's Potential, but if Belt width is not narrow to some extent Driven (Torque Camshaft) I have a dilemma that the Potential of the company can not be used.
By using this product, if you increase the maximum opening amount of Driven, allowance of Belt width increases, so you can minimize Demerit of both sides.
Items are indispensable when aiming to improve the maximum speed by using a short Belt or by using a large VARIER with a large shift amount.
Especially GRAND AXIS something like Belt of about 16 mm is about the same as for 50 cc but it is almost the same as the secondary SieveAssembly but Belt has adopted the thick one which is close to 18 mm so you can not put out Potential in NORMAL state at all. I think that this product is the most recommended one.
On the contrary, even if you use the secondary Sieve in a state that it is not opened, there is no effect.
This product has 0. 3 mm and 0. There is one with 5 mm, but there is not Merit to be especially conservative, so 0. It will not be a problem to pick 5 mm.
However, depending on the combination of Center nut and Clutch, Center nut may interfere with Clutch outer, so be sure to check Clutch outer to make sure before Engine start. If you interfere, just add Shim washer to Clutch outer so it's easy to deal with.
There are also surprising uses.
3-Clutch such as Yamaha's 4KNGEAR and Remote controller jog is compatible as Outer diameter is 107 mm which is the same as Honda. However, because the amount of Offset differs, if you just join it with YamahaOuter + HondaInner, it slightly protrudes. You can also use this Washer for that adjustment.
Aside from that, the 107 mm Clutch outer actually has dimensions adopted for Europe's Minarell Engine. 4 KNGEAR 's Clog has a logo of Minarella! Do you really have imported it from Italy ...?
View detail
since it is not meaningful unless it can perform processing of a torque cam -- attention -- that.
since it is not meaningful unless it can perform processing of a torque cam -- attention -- that. View detail