Reviews
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
I used it to fill in the riddle.
The Camshaft ChainHousing of the Z900RS Cylinder block has a mystery hole that is not used on this Motorcycle.
The diameter of the hole is 11mm. I have been wondering about this for a while, so I use well nuts to fill in this mysterious hole.
I hope they will continue to do so because it is a product line that raises the level of custom culture.
I used a 9.5Φ C550 with a thin neck, and since the parts are just for decoration, I used an appropriate lightweight aluminum M5 bolt and cap.
Other than the mystery hole for the cylinder block, the Center Stand mounting hole on the Left Side can also be filled with this well nut and M5 bolt since the hole diameter is 11mm.
View detail
Good to keep it from loosening
I purchased this product for Exhaust System fixed Bolt.
The lock is tight and will not loosen, so it can be used safely in any location where there is vibration.
View detail
Refresh
We replaced it for Refresh to Timing removing Cowl.
There is a feeling of reduced squeaking.
There's nothing wrong with replacing it before it cracks!
The removed items were cured.
View detail
Thank God they don't sell them at the homestore.
When I installed NAMETALCraft's aluminum chain guard on Over Racing's Swing Arm, the bolt nut on the reverse side was dangerous because it interfered with the chain when I fixed it with the bolt on the front side bracket. I inserted a 12mm Truss Screw from the Reverse side and fixed it with this Cap Nut with Flange from the outside using an AngleDriver. After that, there was no more interference and I am satisfied with the result.
This was helpful because these special Nuts are not sold in Home center.
View detail
Cheaper than OEM
We purchased more because they are cheaper than OEM!
When they are old, they are hardened and I replace them when they are Rose.
This is a necessary component to prevent Cowl from cracking or over-tightening!
View detail
Less expensive than OEM Parts
[How is it used?
I used it to fix my newly purchased Chinese Cowl.
I bought this product because it was inexpensive and had good reviews.
Was the one you received as per Image?
I purchased For M6, but it is surprisingly Large, so it is somewhat troublesome to extend the lower hole.
Was the installation difficult?
The Chinese Cowl originally has an appropriate hole Size, so the hole needs to be expanded.
The work must be done carefully because it has to be made rather Exactly.
It is recommended because it is easy to use once it is fixed.
How was your experience with it?
It is strong enough to fix Cowl.
As mentioned above, Chinese Cowl would be useful as long as the pre-drilling is done properly. (Actually, I prefer Quick fastener, but...)
Note that the price is surprisingly high when used in large quantities. Still, it is much cheaper than OEM parts.
[Was there anything that disappointed you?
Although the product itself is not so great, the size is indicated as large, but I thought it was difficult to image the size.
I felt it would be easier to buy if compatible OEM Parts numbers were listed.
【Review】
It is useful for fixing exterior parts such as Cowl and Screen.
OEM Parts are expensive, so if you want to keep the price as low as possible, this is a good option.
View detail
Half the price of OEM
It had not been replaced for a long time, so it hardened and lost its damper effect, so it was replaced for refresh!
I was quoted to buy OEM, but it cost twice as much as KITACO product, so I decided to buy KITACO product.
I am Large satisfied with this one because it is cosier!
View detail
Good quality
Better quality than Home center, etc.
I would like to see Lock nut in Nylon as well.
View detail
K-CON Hexagon Nut
About quality and texture The quality is good and the packaging About the feeling of use The quality was good, and there was no problem installing it Products to buy together m8 bolt, M6 Washer Difficulty of installation easy Cost performance and comparison with other products About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I bought it for use under various circumstances, but I installed it in the place where the linker moved and I am satisfied View detail
Fixed
The fixed nut of the Rear Sets was old, so it was replaced with a rust-resistant Stainless Steel one.
Quantity:1 Set of 2pcs. not that pricey, new, clean?
View detail
prevention of slackening
Lock nut to prevent loosening.
I am relieved to know that this will not loosen easily.
View detail
Thin type
I purchased this low profile lock nut because the length of the bolt to which the Exhaust System is attached was too long for the normal thickness lock nut to fit over the Limit Screw.
Thanks to this, I was able to tighten it without any problem and I am satisfied.
View detail
Cap Nut with internal lock
This is a Cap Nut with an internal lock.
There is no worry about falling off while driving.
Recommendation
View detail
prevention of slackening
It is purchased to prevent the License Plate Fixing Screw from falling off and loosening.
Unlike normal nut, it is Lock nut with Flange, so it is good for a little bit of safety.
View detail
standardized article or goods
The bracket that the well nut is attached to was damaged, so I decided to replace the bracket and the well nut at the same time.
I bought the cheap KITACO parts and the OEM parts as insurance. When I compared them, I found out that they are the same product from the size to the engraving because they are standard products.
The Well nut I used this time was C-550, but there is a Large size Well nut with L at the end.
Although the price of OEM parts varies depending on the manufacturer, KITACO's well nut is generally cheaper and recommended for replacement.
View detail
Exhaust Nut, anti-dropout measures.
It will be used for the Stud bolt next to the Exhaust Gasket. 。 Apply OmegaOil's BlueGrease to the screw part for rust prevention. 。 I plan to use it with SpringWasher! 。 Tightening Torque will be half of the specified value (because of applying Grease.) 。 It's to prevent the Exhaust Nut from falling out. 。 If you've ever dropped out, how about giving it a try? View detail
rust-resistant
M10 Hexagon Nut.
The Silencer fixed Bolt on my Motorcycle fell off, so I bought and used it as a replacement.
Accuracy is normal. The finish is rather beautiful, and the plating seems to be thicker than the one sold by Rose at Home center. I think it is.
If you get the pitch right, you can install it without any problems, and there's nothing to say about it.
However, it's a little expensive, so I think it's best to just buy it on the side of something.
View detail