Reviews
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
W-1741-058
I really liked how these nuts transformed my Honda Monkey and I decided to repeat this with my Honda Little Cub. The nuts fit perfectly except for two washers (the stem on the Honda Little Cub turned out to be wider behind the thread), I had to leave two washers old on the inside. I liked this purchase, I was satisfied with the experiment. As always, the products of this company are on top!!! View detail
Purchased for dropout prevention
M8Nut is used to fix a self-made Handlebar, but there is a possibility that an ordinary nut may loosen, so we purchased a lock nut that does not loosen.
Bolt used a hand-held anti-theft Bolt, which was both anti-theft and dropout-proof.
I would buy again if the opportunity arises.
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
Genuine Kitaco Well Nuts C550 M5 x P0.8 for spares
I wanted to get soem new well nuts in this size as I did not have any spares in the garage. I have not tried the Kitaco ones and at this price is was a no brainer. The price was really good and cheaper than some on the other brands I could get. I decided to get the Kitaco ones as I have had a few other parts from this brand and I am honestly, very impressed with how well they are made. With a couple of other items in my order, I had them all shipped using EMS and the package arrived in 5 days. Everything was well protected from any damage. The well nuts came in the Kitaco box packet and were well presented. They are a really neat part that everyone should have some spares as you just never know when you will need them. These were the M5 size and this is usually the size that fits with a lot of panelling on a lot of different models. They also fit a lot of factory screens too. The quality of these is not really easy to work out untli you actually use them. I did have a screen that needed a new well nut fitting so I used one of these. Definitely recommend them as they just work how thay should. None of the spinning of the thread and worked exceptionally. Very happy with these. View detail
At the time of Screen replacement
I purchased this product because the well nut was Crack cracked due to deterioration when replacing the Screen.
Compatible with M5 well nut for all Kawasaki vehicles, and is a recommendation because it is more affordable than OEM products.
View detail
Fits: HONDA MONKEY, HONDA SUPER CUB 50, HONDA KITACO cylinder head compatible, HONDA APE 50, HONDA APE 100, HONDA XE series, HONDA CB Series, YAMAHA TT-R50E, YAMAHA TT-R125, KAWASAKI KSR110, KAWASAKI KLX110
Genuine Kitaco Titanium Nuts & Adjustment Screw Set for Yamaha TT-R125
The customer wanted to change out the adjustment screws for something a little more robust and they suggested the Kitaco titanium nut and adjustment screw set. I honestly did not know that Kitaco did titanium but I guess with the great parts they make, why not. The price was really good for what you actually get. With some other parts, I had my order shipped using EMS and arrives in perfect condition in 5 days from being shipped. The screw set came in the Kitaco box and was well presented. The machine work on these screws and the nut is excellent. The threads are all perfect with no burrs or weird edges. They fitted exactly as I expected. I am really impressed with Kitaco as a brand and will no doubt be looking at them for other parts. Thanks Webike. View detail
BlackScrew
I purchased this to install a GIVI Top case. It looks tighter. View detail
Looks rust-resistant
I have not installed it yet, but the OEM bolt of SR400 has rusted, so I purchased this product expecting the Titanium bolt. The OEM bolt is tightened by Hexagonal Wrench, but this product is Hexagon Bolt, so I am worried if I can manage the torque in such a small space.
I would like to post an IMPRESSION after installation.
View detail
For Screen fixation
Material:Well nut that is a Rubber product and should be replaced regularly.
This time I purchased it for fixing Cowl's Screen.
The rubber is hardened to the point of pushing after 30 years, so it would have to be replaced anyway, but the previous owner had tightened it so much that the well nut was deformed and would not come back.
Since it is very common to use M4-size well nuts to fix the screen, there is no problem with these well nuts without having to purchase expensive OEM parts.
Some universal well nuts are too thick for screen fixation, but NTB's well nut is the thinnest type among universal well nuts.
It is truly OEM compatible.
Conversely, well nuts used for fixing brackets of auxiliary equipment would have a thicker flange, making them somewhat unsuitable.
Unfortunately, the Screw that I thought was M4 was actually M5, and this product was not available.
It's all my fault that I couldn't use it, so I don't blame myself.
Well, maybe you'll use it sometime! Maybe!
View detail
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
Product # W-1741-058
To give a beautiful look to the motorcycle, I bought a set of bolts and washers made of stainless steel. Installation takes 5 minutes. Very good design overall. I was pleasantly surprised by the functional elaboration - this is the largest set of 12 parts at the lowest price. I recommend everyone to update their appearance. To give the motorcycle a beautiful look, I bought a set of stainless steel bolts and washers. Installation takes 5 minutes. Very good design overall. I was pleasantly surprised by the functional detail - this is the largest set of 12 pieces at the lowest price. I recommend everyone to update their appearance. View detail
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
Product # W-1741-058
This kit was purchased for the Honda Monkey. The original nuts were coated with oxide, the washers were slightly deformed. A solution to this problem was required. There have never been any questions about the quality of the cube parts, why when we saw this kit, we ordered it without hesitation. I really liked that the nuts on the outside turned out to be larger than the original ones, which had a positive effect not only on the appearance, but also would not have a deforming effect on the washers. The result exceeded all expectations! View detail
For M6, which seems to be available but is not so easy to find, and Flange thin type
Material:Well nut that is a Rubber product and should be replaced regularly.
It is often used for fixing Cowl screens, etc., but in recent vehicles, it seems to be widely used for various brackets and auxiliary equipment mounts.
Large holes can be absorbed by the rubber part, and there is no need to embed the nut in the fixed object.
In DUCATI, it began to be used extensively after 1990, and in the 1991 900SS, it is used in various places on various parts of the body.
It must have been so easy, because Cowl mount was well nut in all places!
The large cowl (and the Seat Cowl in the 900SL) is supported by a bolt called M6, which is a thicker bolt, but the receiving side of the frame is all well nuts.
Of course, M6 well nuts are sometimes used on domestic cars, but the overwhelming majority are M5 and M4 size, so there are not many types of M6 well nuts to choose from when looking for a universal product as a repair item for motorcycles.
In such a situation, this product is Exactly as UniversalWell nut of M6.
There are several types of wall thickness in the Flange section, and this is the thinnest type in NTB.
It is best suited for locations where the design does not consider fixing the object with a deformation of the Rubber of Flange, but simply uses it as an embedded Nut.
View detail
Easy search
It is easy to search for the parts I need. View detail
Fits: HONDA MONKEY125, HONDA MONKEY, HONDA SUPER CUB, HONDA glom, HONDA CUB, HONDA NSR80, HONDA NSR50, HONDA NS-1
This tool sure makes clutch maintenance easier
About quality and texture, I can confirm that the quality is great and that the material used is tool steel that is strong with a durable coating. About the feeling of use, This center lock nut wrench sure makes clutch maintenance easier and can be used to remove the oil spinner also. Allows for disassembly without damaging the special nuts. Products to buy together, The heavy duty clutch kit from Kitaco would be ideal to also add to your cart when purchasing this tool so you can upgrade the complete clutch pack for better engagement and feel. Difficulty of installation, I can say the fitment of the center lock nut wrench for my installation was very easy due to the simple nature of it's use caused by it's compact design. Cost performance and comparison with other products, The pricing of the center lock nut wrench is great, specifically designed for the special nuts from Honda and easier then using random tools and all the other options are price similar. About shipping and packaging, My order was shipped within 48 hours of me placing the order and I received a few emails advising me of the status up until the order was dispatched. I find the link supplied to track my order very useful and the order arrived within the estimated date range. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
Size should be measured properly.
I bought the wrong Size so I haven't used it yet anyway.
Maybe one of these days there will be a need for it. Until then, it is fertilizer in the Screw box.
Rubber quality is good, so if storage is not a problem, it will be Large sturdy for a while.
View detail
Material after more than 20 years.:Rubber products usually go bad.
I had a hard time finding the name of this product, which expands and stops when the screw inside the rubber is pulled when the screw is turned.
Posh face is called Insert Rubber Nut, but it is also called Well nut.
Rubber components change over time. It's inevitable:after 20+ years, most OEM parts are obsolete. Thank goodness there are similar, identical constructions available, thanks to PartsManufacturer.
View detail
Fits: HONDA DAX [Dax]., HONDA CHALY [Shally]., HONDA DAX [Dax]., HONDA CHALY [Shally].
Fits Chaly, Dax and Monkey
Have ordered 3 of these sets now and are always a great fit and finish to any honda with the same threaded shock towers. will be ordering more in the future View detail
Dirty but shining.
Material is designed to prevent rust and to reduce weight to a more comfortable level.:Replace with Titanium
The effect of lightweighting will only be apparent in a world of 0.01 seconds at CircuitLevel.
Therefore, I think it is generally considered to be a dress-up and maintenance product.
There are a number of companies on the market, but the titanium material used and the degree of looseness (individual bites during manufacturing) are not all the same.
The proven βTITANIUM was selected from an accuracy standpoint.
First of all, the appearance is really Parenthesis well, and I am personally Large satisfied because it shines even when it is dirty.
Loosening of the nut itself will occur no matter what material is used, unless it is attached with adhesive. It is not the case that the Nut loosens because it is Titanium.
I don't think it is a story.
Since we are talking about compared to other materials, I think the Level is fine as long as it is checked at the time of normal maintenance.
Incidentally, this product arrived with the O-ring from the beginning, so there was no need to purchase the O-ring with the initial Nut.
(O-rings are not reusable and need to be replaced next time)
View detail