Reviews
Purchased for dropout prevention
M8Nut is used to fix a self-made Handlebar, but there is a possibility that an ordinary nut may loosen, so we purchased a lock nut that does not loosen.
Bolt used a hand-held anti-theft Bolt, which was both anti-theft and dropout-proof.
I would buy again if the opportunity arises.
View detail
Black stainless
When replacing the disc with a new one, the lock nut for fixing was replaced with this Stainless black one.
It is a little pricey in terms of the number of units used, but I am satisfied with the appearance because it is rust-resistant Stainless Steel and Black, which makes it look beautiful.
View detail
BlackScrew
I purchased this to install a GIVI Top case. It looks tighter. View detail
Easy search
It is easy to search for the parts I need. View detail
Size should be measured properly.
I bought the wrong Size so I haven't used it yet anyway.
Maybe one of these days there will be a need for it. Until then, it is fertilizer in the Screw box.
Rubber quality is good, so if storage is not a problem, it will be Large sturdy for a while.
View detail
Material after more than 20 years.:Rubber products usually go bad.
I had a hard time finding the name of this product, which expands and stops when the screw inside the rubber is pulled when the screw is turned.
Posh face is called Insert Rubber Nut, but it is also called Well nut.
Rubber components change over time. It's inevitable:after 20+ years, most OEM parts are obsolete. Thank goodness there are similar, identical constructions available, thanks to PartsManufacturer.
View detail
Black stainless
Since the bracket part is fixed in black, we purchased the Fixing Screw in black as well.
Stainless black looks nice, but the selling price is a bit high.
I wish they were cheaper or had more pieces.
View detail
Purchased for Bolt dropout prevention
[How is it used?
Purchased for Bolt dropout prevention
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy
How was your experience with it?
I'm worried if I don't see them regularly.
[Included Parts:were they on?
(after the -te form of a verb) not ..
[Was there anything that disappointed you?
I wish it was a little stiffer.
View detail
This is it for now.
Sprocket has a Motorcycle of the Showa era? The Plate is attached to the Bolt, so it can be pried with the Driver + Hammer. (M10, Pitch1.25mm, Wrench14mm)
I removed the BuRate and replaced it with this one for now. I made a mistake. I was supposed to buy the one with the loosening stop,
https://www.webike.net/sd/25645278/
I bought this one, so I bit the Nord-lock washer and voila!
At least it's cool now. (Lol)
View detail
Stainless Steel Fixed Nut
The fixed nut of the Exhaust System was old, so we replaced it with this Stainless Steel Black Flange nut.
It is rust resistant, stain resistant, and looks great.
View detail
Fixed Nut
I bought this for tightening the mounting fixed nut as it seems to have run out. It is rust-resistant Stainless Steel and is sold in small quantities, so it is very helpful. View detail
prevention of slackening
The fixed nut in the Exhaust System section loosened due to vibration and was missing, so we installed this one in the hope that it would prevent loosening.
The rebound of the Spring shape seems to be effective in preventing loosening.
View detail
Fixed
The Exhaust System fixing nut was loose, and when I noticed it was gone, I thought Flange nut would be better, so I installed it. View detail
I wanted to make it Black.
The OEM is the same FlangeLock type, but it was corroded, so I bought a Black Stainless Steel one.
Lock type is safe because it is a place where a lot of force is applied.
View detail
900SSCowl RubberNut replacement
RubberNut on Cowl and Cowl Bracket was damaged and was replaced.
I could not get it in with just my fingers, but I pushed it in with a Hexagonal Wrench and it worked.
View detail
Fixed
Used for parts mounting and fixing.
Stainless steel, so it can be used without worrying too much about rust and dirt, and the price is not that expensive.
View detail
I bought Pitch 1.5 by mistake.
[How is it used?
I purchased this product to secure the Engine Guard.
How was your experience with it?
The thing is fine, but I made a mistake and bought 1.5 when I needed Pitch 1.25.
It is made of Stainless Steel called SUS304, so it should be basically rust-free.
Prices are also available in the Quantity:I think it is reasonable for 1 Set of 2pcs.
View detail
prevention of slackening
It is installed to prevent loosening.
Black is more expensive, so here is Quantity:1 Set of 3pcs. is helpful because it is less expensive.
View detail
prevention of slackening
I bought it because I thought it would prevent loosening of the Fixing Screw in the Exhaust System section, rust-resistant Stainless Steel, and Black, but although the product is good, it is expensive. View detail
Replaced with Stainless black
The rear sets are black, but the screws used are silver, which is very conspicuous, so I purchased these screws to unify all the screws used with black.
Rust-resistant Stainless Steel, Black, Quantity:The price for 1 set of 2pcs. is a little high, but it is not so expensive if you don't need to replace them often.
I am self-satisfied because it looks better with Black unified.
View detail