Reviews
To prevent rust on Stud bolt
The 6mm Stud bolt on the Mini bike breaks easily when it gets rusty
I used it so that such a thing would not happen again
I used 4 cylinders because it's a 2 cylinder, and if you have a MONKEY or SUPER CUB, you can use QUANTITY:2pc is enough
It may not be a good idea to manage Torque, but you can use a thin layer of Grease on the Stud bolt The assembly will not produce any Bolt rust
Also, the long nut makes it easier to maintain in tight spaces
However, the outside of the Nut itself is treated with plating by Steel, so if you leave it unattended, the outside of the Nut will get rusty It is
It's cheap, so I don't blame you
View detail
Mostly successful
Cowl fixed well nut rotted
In OEM, Quantity:1 Set of 10pcs.
The rottenness is 1pc.
Quantity:2pc. Set
We were able to get the desired number of items for KITACO Universal Product
View detail
Fits: HONDA CB400FOUR (air-cooled), HONDA CB400FOUR (air-cooled), HONDA CB400FOUR (air-cooled), HONDA CB400FOUR (air-cooled), HONDA CB350, HONDA CB750 Four(CB750K)
Blue Spring Memories CB250EX
I had a CB250EX when I was in my 20s, but after 40 years, I got nostalgic and kept looking for a good one I finally got my hands on this 1972 model
"MissionReturn spring needs to be replaced I got it knowingly, knowing that this was the explanation in advance However, this Spring has already been discontinued I managed to get the unused Spring stock at Oakshon overseas I removed the Clutch and opened the Right Crankcase Cover to replace the spring stock I had planned to have to, but the GEAR of Clutch outer and The GEAR on the Crankshaft side is a double layered GEAR with a gap of one tooth on both sides The Crankshaft side GEAR has the structure that the Oil Filter is integrated into the Crankshaft side GEAR In order to pull out the Clutch outer, the Oil Filter must be removed Remove the RotorCap and remove the RotorCap It is fastened with a Lock washer There are traces of it being opened before, and there are also dents from removing the lock nut with Graver at that time There is a large slotted screwdriver instead of a Graver Large slotted screwdriver is used instead of Graver according to its precedent Loosen the lock nut to the lock nut, remove the Oil Filter and Clutch, and aim "MissionReturn spring Finally, we meet at the I was able to replace it safely The last issue is the lock nut with the Graver mark on it I want to assemble a new Nut with tools, and although it is possible to get both Nut and Washer respectively, my problem is that they are not available Mr. We-Big! What a Quantity:Set Lock nut& for BRCClutch center; Lock washer It's available as a Moreover, it is cheap at 1057 yen The shipping cost is 380 yen all over the country, but this product is 250 yen because it is Small object of delivery, and the total cost is 1,000 yen I snapped it up for 307 yen and took the opportunity to clean the ClutchFilter and While making your own Crank Case CoverPacking from Packing Paper And wait for it to arrive Tightening it with Graver again is a bit of a trick, so I machined a 22mm SocketPiece Special tool for lock nut? I also made my own A few days later, Nut and Washer arrived earlier than I expected I installed Crank Case Cover Turned the oil and started the Engine Outlook Blue Spring Memories CB250EX has been revived
View detail
It's an inconspicuous part
I used it to hide the threads of UniversalMeter It's a good fit with the appearance of the UniversalMeter
I like the fact that it's black and it's discreet
The only one whose cost is more expensive than Universal is Minus
View detail
BlackLock nut, which is not often seen
The silver color of the Nut stands out when the Custom is unified with the black color Black Nut is also seen in Universal Product, but it's not as black as the Lock nut If it is, you will hardly see it I think this is a party where you can get a little bit of attention View detail
It's changed!
I installed it on my LEAD 100
Two in the front fork, one in the rear suspension, and
I felt Front had changed with HaDrill
I've been picking up the fine Gap and getting through to the Handlebar
That's gone
Even Scooters are different, and I'm Big Li
By the way, I don't think there's enough Rear to experience it...
View detail
functional
It took a bit of time, but it was the same as the OEM etc I thought it was no longer available, but I was able to get it successfully It felt good to use View detail
Firmly fixing it is difficult and impossible
Purchased the SetrabOil cooler to install on my MONKEYFrame But I think there are some to use it as a supplementary
Because it is impossible to fix Firmly only with these Parts, it is used only as an auxiliary It is possible to do so
View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-S1000, YAMAHA YZF-R6, YAMAHA YZF-R6
Parenthesis better
Remove the OEM Nut and just replace it (Lol)
Parenthesis is good
But I am worried about the strength because it is aluminum It is not a thing to be taken off and put on and off so often
View detail
If it starts to rust, we'll replace it
It's well made, and the quantity:1 Set of 4pcs
I am using it to install the Horn If you have a more rounded head Cap Nut, this diameter is also available at Home Center, but you can divert it I bought this one because I was worried about whether I could use it or not (I'm not sure if it is possible to tighten up the bolts with the low cap nut when the bolts are long (That it might be)
It's as elaborate as you'd expect, but since it's a screwdriver, I'd rather it didn't fit, but.. AmericanQuality or not, it's perfectly fine
Also, if you tighten it up in the Socket, it will scratch and corrode slowly from there over several years, so Even if it's a hassle, I think it's a good idea to close with Spanner
View detail
Zita is sure!
I bought it as an Exhaust SystemNut To be honest, the price is high, because the price of two pieces of Nut is 1800 yen & hellip; Titanium Then it's no use
However, there is also a Lock Function, and the accuracy is good
View detail
Fits: HONDA Super Cub 70, HONDA Super Cub (HA02), HONDA Super Cub (C90 type), HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub]., HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub].
Cap Nut & Washer for Honda Super Cub
I purchased this set of stainless steel bolts and washers to replace old original parts that were corroded and badly worn, the quality of these parts turned out to be very good, the stainless steel is thick enough to withstand the required forces. The installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for the fast delivery and great packaging! I purchased this set of stainless steel bolts and washers instead of old original parts that were corroded and worn out. The quality of these parts turned out to be very good, stainless steel of sufficient thickness to withstand the required effort. Installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for fast delivery and excellent packaging! (Translated by Google Translator) View detail
Excellent eye sightness
We always use this Nut when exchanging Sprocket.
Accuracy and making are firm and installation is completely no problem.
Customized feeling improves greatly simply by exchanging with NORMAL very beautifully in the state of Anodized.
There were things that the accuracy was solid, so there was no problem in the installation.
After all it's okay if you can use it in various places as soon as the price becomes cheaper.
View detail
The shape is different from the image
Than a thick thing reached the part of the bracket than the image.
It makes me feel like I jumped out of SEA BASSOEM.
If the shape is wrong, it might be cheaper to buy Universal Product at Home center.
View detail
Accuracy...
Since OEMCap Nut of Cylinder head came, I bought it for Replacement together with Reinforced Stud Bolt.
1 pc out of 4. The accuracy of the thread of the screw was bad, and the thread of Stud bolt was broken owing to gnawing. Is it inferior to Made in Thailand's OEM Parts and is not JAPAN?
View detail
Cheaper than Kawasaki OEMParts
I used it for 1400 GTR. Although it is used as a substitute for OEM Parts when exchanging a Well nut that is strange when you remove consumables or Cowl, there is no difference in Size or use feeling. KawasakiOEMParts (92015-1757) That's 1pc. Because it is about 200 yen, this item is considerably more affordable. I think that I will continue using it. View detail
Bolt is too suspicious
Before injection injection Bolt has used it
Even at over-the-counter sales, it is also a product that can be sold with confidence that it may be decided not to buy it after purchase by DIO
This time there are things that Reduce shipping fee is over 3,000 or more
I tried to buy it for Rear suspension
After all the ride feeling has improved somewhat.
Next time I will look at the opportunity and I will attach it to Front fork
View detail
This is good, is not it.
Quantity with certain Amazon ○ : Set of 50pcs. I bought a cheap commodity, but when I turned Screw, I got Nut and it did not become usable so I bought this item. I could firmly fix it. Please also be careful when you buy a certain Amazon 0 item. This item is recommended. View detail
Fits: HONDA glom, KAWASAKI Z125 PRO, HONDA MONKEY125, HONDA ZOOMERX, HONDA ZOOMERX, HONDA ZOOMERX, HONDA glom, HONDA CB400 F (JF52-1000001-), HONDA DAX125, HONDA 400 X , HONDA CB400 R, HONDA CB250 F , HONDA CBR250 R, HONDA CBR125 R, HONDA MSX125 SF, HONDA MSX125, HONDA MONKEY125, HONDA CT125, HONDA CL250
SP TAKEGAWA (Special Parts TAKEG Stem Nut for Zoomer-X
This nut is very well made and it looks awesome on the bike. I bought it black with gold on the center. It took me 10 minutes to install it and it was very easy. The only BUT i can find is that is a little bit expensive. View detail
Fits: HONDA Super Cub 70, HONDA Super Cub (HA02), HONDA Super Cub (C90 type), HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub]., HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub].
Is good
I was looking for something that will not rust as it will run on the mountain with CUB and become muddy.
It was not possible to attach it to the clipping point on hand, the Up type muffler of the water circle RACING.
The water head Racing Up Exhaust System may be used if there is an ultra thin socket?
View detail