Reviews
Anodized for fine-tuning of hand guard, rust-free
[How is it used?
We used it to fine-tune the CYCRA hand guard.
Yamaha cars are MASTER to avoid Hit because of Banjo on the outside.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
There is no problem just to pinch it.
How was your experience with it?
Since the product is Anodized, we hope it will not deteriorate.
Normal aluminum colors tend to cut-out and rust.
[Included Parts:were they on?
Color only.
[Was there anything that disappointed you?
There is also a length Lineup, which is just right because it is Anodized, but
It's a bit expensive
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Small but Large!
*Motivation to purchase
I could not find a spacer with the right thickness to install the ZETA ED Skid Plate.
When the clearance between the skid plate and the down tube seat is measured with a caliper and found to be 6mm. What shall we fill this Clearance with?" I was simply worried.
01mmWasher×6 sheets? ⇒Not very efficient to look and work with? ，Cut an Aluminum round bar to 6mm thickness and drill a 6.5mm hole in the Center? ⇒Since there is no ball machine or lathe, it is labor intensive and the material is expensive and not readily available?
0 Casually searching Spacer, I found that it is Aluminum, Anodized Treatment, available in a choice of colors, and even cosier!
I decided immediately to buy it.
Installation
The quantity is placed between the skid plate and the mounting surface of the down tube, together with the washer.:You just need to set it.
Insert the mounting bolt into the skid plate, insert the washer and spacer into the bolt that protrudes from the back of the bolt, and then tighten the quantitative bolt on the mounting surface of the down tube to prevent it from falling out.:Pair (for Left and Right) The tightening was divided into several times to make it even, etc.
*Appearance after installation
0It is not visible from a normal viewpoint. When you look through, the gold anodized Spacer is quite noticeable.
0Aluminum spacer was 5mm and Washer was 1mm, total 6mm spacer was just right.
0Although the spacer is not usually visible, I think it would have been better if the skid plate was shaped along the down tube side, so that the spacer would be thinner.
*What I actually felt after using it.
○ Aluminum spacer If you think about making the same kind of spec. by yourself, it will cost you a lot of time, money, strength, and energy.
0For myself. Spacer." = "Small Sana Giant Yes, sir!
View detail
Just as it says!
Exactly what I was expecting.
Nothing more than what is written, nothing less than what is written.
View detail
Aluminum textured Spacer. High precision too!
This product is a highly accurate and Aluminum textured Spacer, used for height matching of the RearBOXCarrier! View detail
alignment
The Rear Sets are replaced together with Bolt for alignment.
It would be nice to be able to choose Size, etc., but I wish the price was lower.
View detail
Useful for adjusting the length of Screw.
I like the fact that Spacer comes in Gold! View detail
It's great as a general M6 ScrewSpacer though.
I think it's the best in terms of quality and texture.
There is no other place to praise, but I intended to use it as a Mirror Spacer of FZr1000 which is our beloved car, but the outline was too large to use.
I think it would be a better product if there was a Lineup of external form.
The video shows the FZr1000 Touring scenery after the maintenance was completed.
View detail
I used it to increase the height of the Handlebar.
Although this spacer is aluminum, there is a high-grade feeling because it is nickel plated. I was looking for a spacer with a good finish and shape because the mounting position is a noticeable point. View detail