Reviews
Used for Cowl fastening points
[How is it used?
Used at the fastening point of Under Cowl.
How was your experience with it?
This Rubber Collar is placed between the collar and the part that is fastened with Bolt to fix the Cowl.
Cowl's Wobble will be suppressed.
It's easy to get at the supply store and is very helpful.
View detail
Not too flashy.
You can casually plug the Bolt hole.
It's so plain you won't even know it's on unless you point it out.
That's a good point.
It can be installed by simply applying a cloth and lightly tapping with a plastic hammer.
I just think the price is a little high for a plastic cap...
View detail
I was able to get the same Large size for less!
As a matter of fact, when I bought Handlebar Mounting of a certain company and was installing it, I accidentally dropped the attached Spacer by slipping my hand, and I couldn't find it as it was.
I've been in touch with the manufacturer. "There are no Repair Parts. "Please look for the same shape (they did list the dimensions) in Home centeretc." The reply, I was actually a bit confused.
So, when I searched by webike when I was in trouble, I arrived at this and was able to buy it safely.
The size was also finely engraved, so I was able to procure the exact same Large size at a lower price.
They've got plenty in stock, I order and it's here the next day!
It was really helpful
View detail
I'm trying to get Lever to stop rattling!
[How is it used?
We are playing Enduro with Off-road motorcycle.
I was looking for something like a Shim for my Clutch lever, and I found this product. And I bought it.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Remove the Pivot and after cleaning, apply a thin coat of Grease and insert the Shim here and you're good to go.
How was your experience with it?
The lever that was moving up and down stopped moving and became able to cut smoothly.
I'm happy with the Large variant because of the way I run and play with the Clutch a lot.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Measure the shaft diameter of your Pivot before you buy it. I made a mistake once and bought an M6.
ZETA's Clutch perch was an M8.
View detail
It's quite noticeable.
12 pieces of both SIDE are replaced, so the price is quite high!
but I think it is highly satisfying.
View detail
The finish was beautiful.
It was good because there were no things that fit Exactly.
And the finish was beautiful.
View detail
Finish as per image
I finished it with Gold parts on Silver body. I don't know why the standard is Lime green, but I guess I wanted to express the cuteness.
The texture, Size, and color were all as Image.
View detail
for adjustment
To adjust the brake lever & pedal place
I feel good that the rumble is at its smallest limit.
View detail
necessities
It seems expensive, but I can't do without it.
I think you should definitely put it on.
View detail
JC92 can also be used.
JC92 compliant.
It is recommended to use Rigid Handlebar to increase the amount of information on the car body.
You can also experience this with the original squishy Front suspension.
But the vibration is transmitted to Direct, so it is easy for your hands to become numb.TradeOff.
View detail
Appropriate size for Ninja1000
I bought it because the Pin supplied with the DAYTONA Front Stem Up Stand was limited to 24mm and the Ninja 1000 needs 27mm.
Of course, this product is made by J-TRIP and not by DAYTONA, so it is not a compatible product.
However, I thought that the inside diameter of a large body like this is the same as the standard! So I bought it, and tried to insert it into the smallest one of the attached pin of DAYTONA (maybe)... Exactly.
In fact, I was able to work with it in that state, but it is originally fixed firmly and used, and the strength is uncertain and may be damaged someday, so if you are poor and want to be able to make a stopgap, please do so at your own risk.
View detail
Just the right thickness
When I installed the Rear Sets, the Master Cylinder interfered with the Swing Arm and I was looking for a 3mm Spacer.
Parts mass merchandisers in the neighborhood are always 1 to Quantity:2pc. I bought this from Webig because they only had about a Set in stock and I wanted 4!
If I am not in a hurry to buy a part, I go to a mass retailer and buy it from Wehbig.
View detail
Instead of Shim adjustment of RADIAL CALIPER
Used for Shim adjustment of RADIAL CALIPER.
I changed the Rotor to a slightly larger one, so I used it to position the Caliper.
I am satisfied with the accuracy of this product.
I love that it comes in a variety of thicknesses.
View detail
K-CONParts, the one that scratches the itch!
[Usage]
Due to the change of Axle Shaft diameter by WheelConversion.
By inserting it into a 12mm Axle Shaft, it can be used as a Shaft with an outer diameter of 15mm.
【Motivation or reason for choosing or purchasing
There are two types of CUBSeries, one with a larger axle shaft diameter and the other with a smaller axle shaft diameter.
The hole diameter of the Swing Arm is 15mm and the Bearing hole diameter of the Wheel side is 12mm.
I was wondering if there is a convenient collar that can be inserted into a 12mm shaft to make the outer diameter 15mm. I did a search and found out that there is!
As you can see, K-CONParts has a great lineup of small items that are compatible with a variety of motorcycle customs.
[Fit & Feel]
We were able to do this with Cananoco, which is relatively easy to process and cheap to cut.
It was also easy to smooth out the sections with File.
It seems to be strong enough because I can drive without any problem after installation.
View detail
It's great as a general M6 ScrewSpacer though.
I think it's the best in terms of quality and texture.
There is no other place to praise, but I intended to use it as a Mirror Spacer of FZr1000 which is our beloved car, but the outline was too large to use.
I think it would be a better product if there was a Lineup of external form.
The video shows the FZr1000 Touring scenery after the maintenance was completed.
View detail
For adjustment.
I used it to adjust the width of my DAYTONA rear stand hook!
I put on 3mm, but I think 5mm would have been better…
It is helpful to have various Size.
View detail
บู๊ชรองน็อตที่ได้รับ ขนาดสินค้าตรงตาม คุณสมบัติของสินค้าในหน้าเว็บ สินค้าคุณภาพดี แข็งแรง ทนทาน มีขนาดให้เลือกหลากหลาย View detail
It comes in a whole range of sizes, so you can choose!
When changing the Handlebar, we needed to change the mounting of the Steering Damper and used it as a spacer for height adjustment.
For M8's outline φ20mm are suitable for the area where the steering damper is hard to be installed. 15mm height was purchased and then the height was shaved off by 2mm to 13mm to fit the car. The finish is beautiful and it doesn't look like it's been taken off.
If I ever need a Spacer for any kind of DIY installation again, I'll be looking for one from this K-CON lineup.
View detail
You can find the exact Size you want!
If you're doing maintenance or custom work, you'll probably use color a lot, but it's inconvenient because it's surprisingly not available at Home center or even in stock at mass retailers.
I used to use several layers of Washer as a color, but it didn't look good….
After all, a solid color is good! It's also a good point that it's Black Anodized so it doesn't stand out!
View detail
In Footpeg's colors.
Used for the Footpeg colors, slightly longer Bolt and Quantity:You can extend the footpeg a little bit if you build it in Set.
I think that this will be a setting of personal preference, but Universal color is infinitely large in usage.
View detail