Reviews
Looks good, but too shoddy.
Vertia's stuff is basically too shoddy.
It looks cool, but this product is just terrible. Scratches are common, screw holes don't fit, and if you look closely, you can see the quantity.:Pair (for Left and Right) Asymmetry.
ScrewQuantity is used to attach the Parenthesis well, but it is not originally used to attach the ScrewQuantity:The handlebar is not perfect, but it hits the cover of the Radiator, and for some reason, it only hits the Left (as others have done). (So did others).
If you want to put Parenthesis well, you need trial and error.
The price for this Level is unbelievable. Incidentally, the Wide Upper Cowl was also quite poor. I don't have a picture of it because I put it on. (If I take it off again, it will be a hassle to adjust it again.)
View detail
Good looking Fitting?
Material purchased at Axxon for about $5,000 for about 6 months.:Material of Carbon Style:I was using PlasticYAMAHA Super JOGZr Wing Blackettes. The shape and fitting were perfect, but it looked cheap, so I bought the Barrier sheet.
First of all, the holes are messed up.
Quantity:Pair (for Left and Right) asymmetry (If you force it to widen it, it looks like it could be done, but it might break.)
As mentioned in other reviews, the actual product is different from the picture shown in the introduction! (I'm ok with design-wise).
I managed to install it, and I'm glad it looks so classy. if only I can get through Fitting, it will be Recommendation. No, I'm not going to make a recommendation, but … I'm not going to make a recommendation.
View detail
It looks good, but ...
There may be Rose variation in accuracy.
On a 2022 CBR250RR, I could not install it without curving it inward due to the incorrect position of the screw holes.
If you try to install it in that state, it interferes with the Cowl side and rubs against it.
Thin double-sided tape is used for the front side to drop further down to the quantity:1 Set of 4pcs. or so stacked on top of each other.
It will look cool, but I think the double-sided tape will probably come off tomorrow.
I will likely have to machine the Screw hole location when I have time.
View detail
It's not accurate.
I was attracted by the look of the product.
Frankly speaking, I wish I had not bought it.
It is not worth $27,000.
First of all, BALI is amazing.
My bad for being careless, but the Edge part. Hmm?" Is this BALI…?" So I traced it with my finger and it cut my finger.
In the meantime, the entire BALI removal is a must.
Also, it is a combination of Bracket of Gold genus and Spoiler of ABS resin, and it is hand-finished and processed by puig, and it is Quantity.:Pair (for Left and Right) The shape was different in
When I put it on for the time being, the Right Side hits the DummyDuct as hard as it can. When I cut the Handlebar by force, the Right Side was so hard that it was cutting into the Spoiler and made a cracking sound.
I had no choice but to cut off the area hit by the luther as much as I could, referring to the Left Side, which was not hit.
"If you shave off that much, you can't hit a rock…"
But this time, the Bracket itself of the genus Gold was hit.
There is room on the Left Side but not on the Right Side.
Is there something wrong with the way it is attached? I tried to adjust it by loosening the screw, but it only attaches where it should and it only shifts a few millimeters, so I was out of luck…
Could it be that the DummyDuct of the MT09 itself has become dislodged? I thought it might be a problem, but it wasn't. ….
To be honest, is this a defective product? I think, "I'm going to have to give up and be patient and use it," but since I've shaved it off.
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
A bit sorry
Is it a matter of Material, if you run at high speed with bae LePera, the part put in the hole between Headlight will come out and come off.
Then, the included Double-sided Tape was easy to take out like a Type that does not match this product.
I am currently using other powerful Double-sided Tape, but it is still being explored, so I'm seeking it now.
There is plenty of BALI and it's a pity that the making is disappointing for the price.
It looks pretty cool so I am satisfied there.
View detail