Puig Motorcycle Spoiler Reviews

Filter

Write a review and get Webike Points!

Reviews

Puig

14 Oct 2023

Engine Spoiler

Fits: YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 TRACER, YAMAHA MT-09 TRACER GT

Japanese Webike user

4/5

Don't be a GunDam generation.

Dear Racer riders.
Have you ever felt a sense of rich volume in the upper part of the Front, but a sense of loneliness in the lower part of the Front?

Of course, I think that being Refreshing without anything is a design with a sense of lightness, but I chose this one to give an extravagant feeling to the underbelly of Small students who have been riding only Full Cowl to a certain extent.

The smoothness of the installation of such cowls is half of the difference between good and bad quality, but this pooch was easy to install due to the good dimensional accuracy of both the body and the bracket.

Now, if we look at it from a distance, we can see that it has a very good extravagant feel.

I don't feel any actual aerodynamic effect at all, but the increased volume on the underside of the car somehow created a sense of visual stability.

Items is not inexpensive, but it is a must-try for those who want a different feel for their partner. View detail

Puig

04 Feb 2023

Side Down Force Spoiler

Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10RR

Japanese Webike user

1/5

Puch SIDEDownForceSpoiler

In conclusion, it is absolutely impossible to install it properly.

If the pattern paper is Quantity:I also had trouble with only 1pc.
And the pattern paper is not Exactly to match the top?
The location will change by about 5 cm depending on whether you want to adjust it to the bottom or the front or the back

The procedure is different if you refer to the Webike Product Page video for installation
In the video, Plate is applied first, and after 24 hours, Rubber rubber is placed over it.

Product was sent already installed!
This is because the Plate is located behind the Rubber Rubber.
Rubber rubber like Toilet's SUPPON will rebound like Spring and interfere with installation.

I looked it up on the Net and found that those with strong final strength have weak initial strength.
We are a GarageHouse, so our cars and motorcycles are both heated and cooled in the house!
Compress and paste for 1 minute at room temperature above 28 degrees Celsius or
I tried and tried, but it was impossible.

Emon sold separately (amon) Ultra Strong Double-Sided Tape (for Bumper, Spoiler, etc.)
Buy Strong Fixing Type White 25mm×width 2m×length 1.14mm×thickness 1.14mm 3910 for outside of car and
I machined and installed it.

The product is quite straight and is to be mounted on a curved cowl.
It's not so much that it's attached as it is that it's forced to be attached with Strong Double-sided Tape!
The shape does not fit the side cowl of the ZX-10RR at all.

I'm inclined to say that it's a 2021ZX-10R/ZX-10RR exclusive part.
ZX-10RR looks straight but Cowl is quite curved
It doesn't fit at all, especially the Right Side is almost floating.

If this is what you're talking about installing, I'm pretty sure it applies to all other Manufacturer's Motorcycle's.
Whether it is YZF-R1M or CBR1000RR-R, it is possible to paste it!

At the moment, I've driven about 50km to try it out and it hasn't been removed.
It looks cool, so that's good. View detail

Puig

21 Nov 2022

SIDEDownForceNAKEDSpoiler

Fits: YAMAHA MT-09, YAMAHA MT-09 SP

Japanese Webike user

4/5

I thought the Radiator guard area was kind of lonely.

I didn't like the feeling of the Handlebar or lightening or floating at high speeds, so I ordered this to see if it would help stabilize it.

The Meter visor is also made by the same company, so the pouch was my favorite manufacturer;
First of all, the bag had a thick cushioning material, but perhaps due to vibration during transportation, the bracket for fixing the blinker to the bag was torn off and popped out, and the exterior parts were wound or even carved into the bag.
I immediately reported this to WEBIKE, who negotiated with the distributor and successfully replaced it with a good one. However, I was a little puzzled by the quality of the product, as the left side bracket was badly distorted and the screw holes did not fit unless the bracket was installed very forcibly.
In addition, the shape of the Wing to be placed inside in the instruction manual is Quantity:Pair (for Left and Right) I was quite troubled by the fact that it was listed in reverse, but the spacing of the Screw holes is Quantity:Pair (for Left and Right) The two are different, so they can only be installed in a way that allows them to be attached.
It looks like there is a wound on the inner wing, but there is a protective film attached, and the wound is only on this film, so it is polished when removed. However, this film is really hard to remove and frustrating.

I could have just returned it if I didn't like it, but the design (shape) is very stylish, and I found it attractive enough to pretend that there were no scratches or that I had to bend the mounting bracket by hand while forcibly attaching the bracket. Can't be helped?

However, from a performance standpoint, the 2kg increase in DownForce? I think it is still a matter of whether you can come to terms with this price, which is more Style-oriented than performance-oriented, since you may not be able to feel it unless you are at very high speeds.
Other products such as Visor made by the company are of very good quality and may be limited to this product or this ROD.

I'm happy with the Design for myself, so I'm glad. I can't say that I am completely happy with it, but … let's just say it's because of the recent depreciation of the yen. View detail

Puig

16 Mar 2022

NAKED Front Spoiler

Fits: YAMAHA MT-09, YAMAHA MT-09 SP

Japanese Webike user

2/5

It's not accurate.

I was attracted by the look of the product.
Frankly speaking, I wish I had not bought it.
It is not worth $27,000.

First of all, BALI is amazing.
My bad for being careless, but the Edge part. Hmm?" Is this BALI…?" So I traced it with my finger and it cut my finger.

In the meantime, the entire BALI removal is a must.

Also, it is a combination of Bracket of Gold genus and Spoiler of ABS resin, and it is hand-finished and processed by puig, and it is Quantity.:Pair (for Left and Right) The shape was different in

When I put it on for the time being, the Right Side hits the DummyDuct as hard as it can. When I cut the Handlebar by force, the Right Side was so hard that it was cutting into the Spoiler and made a cracking sound.

I had no choice but to cut off the area hit by the luther as much as I could, referring to the Left Side, which was not hit.

"If you shave off that much, you can't hit a rock…"
But this time, the Bracket itself of the genus Gold was hit.

There is room on the Left Side but not on the Right Side.
Is there something wrong with the way it is attached? I tried to adjust it by loosening the screw, but it only attaches where it should and it only shifts a few millimeters, so I was out of luck…

Could it be that the DummyDuct of the MT09 itself has become dislodged? I thought it might be a problem, but it wasn't. ….

To be honest, is this a defective product? I think, "I'm going to have to give up and be patient and use it," but since I've shaved it off. View detail