Reviews
Headlight guard for CROSS CUB
Headlight guards for CROSS CUB are available from other manufacturers, but we purchased this one because it is the most stylish and does not interfere with the function of the Light.
The installation must be done in accordance with the Instruction Manual by loosening the bolt securing the headlight one side at a time, otherwise the angle of the headlight will change and it will be difficult to readjust the angle.
Attach the Acrylic plate to the GuardBody yourself, but be careful not to tighten it too tightly as it may break.
The other item in the photo is MORIWAKI HornGuard B TypeSilver 03810-20Z01-00
View detail
Fits: HONDA TRAIL125, HONDA CT125, HONDA CT125, HONDA MONKEY125, HONDA MONKEY125
Only full cover headlight guard available
As aslways Zeta hit it out of the park, the only light guard that actually covers the entire headlight with a piece of arcylic bolted to a nice alloy frame that enables unobstructed view of the headlight, but 100% protected. The others are just a bit of thin steel wire/tube that will not stop rocks or similar to hit the headlight. Installation was super easy !, also works with all the other Zeta/DRC accesories. In my pics you can see it with the Zeta ADV windsheild View detail
Installation is easy, but ….
It is easy to install but … I drove it at night and it is Lighter and darker than expected.
Therefore, it may be better to install it only when going on forest roads or the like, rather than putting it on at any time.
View detail
good buy
I'm glad because I wanted a little bit of martial arts, although the round eyes of SEROW are also good. View detail
Fits: HONDA CRF250RALLY, HONDA CRF300RALLY, HONDA CRF300RALLY(S)
ZETAHeadlight guard CRF250
I chose it for its Brand power and I was right there. It looks very rugged. However, it is too tough, so it depends on your taste. The installation is relatively easy if you have the right tools. Be careful not to scratch the GuardBody or the car body. If you are worried about it, you can use Tapeetc. to protect it. I don't know if the screws will loosen, but it may be necessary to check the tightening periodically or to apply a very small amount of screw lock agent. The cost performance is up to the buyer, but I think it would be higher if it didn't have the ZETA logo on it.
But overall, I'm satisfied with Large.
View detail
Fits: HONDA CRF250RALLY, HONDA CRF300RALLY, HONDA CRF300RALLY(S)
Wow that's cool
There is no doubt about this.
I like it very much
View detail
For light protection and dress-up
good point
Light can be protected
... be cool.
A bad point
Light gets a little darker.
Installation was easy after reading the Instruction Manual.
However, since the light influence on the light is large depending on the installation angle, it is necessary to work while confirming the angle of installation.
It comes with a polycarbonate board, so it can be protected from small flying stones. The board can be purchased as a Single Body, so you can rest assured.
View detail
Dress-up
I think the purpose of this is to protect the headlight from mud, stepping stones, tree branches, grass, etc., but in reality, I think the dress-up effect is much larger. It's just a small part, but I think it looks much better. View detail
Fits: HONDA TRAIL125, HONDA CT125, HONDA CT125, HONDA MONKEY125, HONDA MONKEY125
Unique design
Installation is very easy and the design is unique. Acrylic plates for protection were included, but I didn't use them. Anyway, I like these parts. View detail
The quality is okay, you get what you pay for
The guard fits well with the headlight, the outlook beats other brands', that is for sure. The installation is extremely easy, it only took me 5mins. And I am sure the plastic cover will do a descent job in protecting the light. However, the quality is just okay, I had to sand the entire guard again because there were many steel burrs, but it's okay for those who are fond of handcrafting. I resprayed the guard in camouflage green since it fits my bike better. All in all, I am satisfied with the final result. View detail
cute little
I'm very happy with this product. View detail
A little disappointing
I installed it for dress-up purpose.
BALI is terrible and M4Washer is Quantity.:I was a little disappointed that I was 1pc. short.
I am satisfied with the Design.
View detail
Design is good
The design is cool. It is a great item with protection in Serow250 as well. It's like I'm changing from a gentleman to a bodyguard. View detail
Caution! It is made of Polycarbonate.
The illuminated part of the light is made of Polycarbonate. It is recommended not to use any kind of screw lock agent. I got cracks here and there soon after using it.
As for the installation, it took me a while to install because the Bolt in the Light comes off easily. However, the quality is high and overall I am satisfied with this product.
View detail
Enough for a CUB
I prefer the reticulated Guard, but if you consider the protective polyethylene plate as a consumable This is better for protection from Small stones and sand The original OEM Headlight alone is darker and the light transmission of the poly plate makes it a little darker, but Even the reticulated Guard interferes with the floodlighting, so I think this is a tolerable level View detail
Parenthesis good
I decided to go with this one in a relatively sporty way for these types of Parts!
The surface is lightly pearled and the texture looks high
The installation took about 10 minutes, but when the bolts in the headlights came off during installation, they fell off I worked a little carefully because it seems to need to open the Headlight, but I used Large It was strong
It's hard to see from the photo, but it's clear and transparent (Polycarbonate) It comes with a Protector
View detail