Reviews
Pasting tools need to be prepared separately
Since someone has already written about the details of the product, I would like to add to that.
The only content is decal.
You will need to prepare your own Squeegee and degreaser for the paste.
The pressure-sensitive adhesive, like Wrapping Fill, allows for temporary fastening and is very easy to work with.
Here! and once positioned, crimp it to the grizzly.
The protective film allows Squeegee to be applied without hesitation.
If you use masking tape or other means to manage the skimmer, I think you can divide and paste the et cetera with a good degree of accuracy.
View detail
For Dress-up of Wheel
CB250R was finally delivered and I used it for Dress-up!
And it's easier to put it up before the Wheel gets dirty.
This time, I'm going to use this product, which is a little bit expensive.
After all, there is a large difference in the image between pasting and not pasting.
I do the same task 16 times, so by the end you get used to it. lol
I used a mild detergent to apply it.
However, I did apply a sticker without text at the end.
I think this is a slightly different Image.
I put up one picture and stopped.
View detail
Easy to Ime Chain
I want to brighten up the Tire section a bit,
To match Body's Red.
MDF Mirror red 6mm is attached.
I forgot to buy the Sticking Gauge for Rim Stripe, so I'll put it on by feel.
Well, I was able to do it just fine.
View detail
MDF Rim stripe 4M Red
Used for 10Inch wheel of ADDRESS V100
Selected because it was good to use it on the GSX-S of the Main vehicle.
You can choose the width of the rim sticker according to the vehicle Image.
This time, 4mm width is recommended as it tightens the foot.
View detail
It's easy to paste.
I used it on my friend's Scooter. After degreasing and applying it properly, it did not come off even if I washed the car hard. I used to put a cheap product from another manufacturer on my friend's Scooter and it came off in less than a week! View detail
Fits: Others 10Inch wheel car
This product is inexpensive, and is the one point of the footwear.
I thought it would be difficult to install, but the material is very soft, almost wrinkle-free, no air bubbles, and very easy to apply. View detail
For those who want one point for the suspension...
I am a Rim Sticker Large lover, so I have applied Large stickers on my motorcycle for many years, but I always buy MDF's split type stickers because I think they are very good and easy even for an amateur like me.
When you look at it up close, it may not look like a nice circle, but when you look at it from a distance and while the tire is rotating, it already looks like a large body circle, so it's OK! I put it up with a forgiving attitude.
View detail
Fits: Others 17Inch wheel car
Silver but White
I bought it while shopping because it was inexpensive.
It is silver, but it looks white depending on how the light hits it.
The adhesive strength of the Sticker itself is weak, so it is better to warm up the Rim when applying it in cold weather.
I put it on in November and even after degreasing and sticking it on, it started to lift off the adhesive surface the next day lol.
With a 17-inch wheel, there is a little extra Sticker.
I think it's fine if you just want to use it as a trial. If you want to paste and dress-up beautifully, please contact us! If you want to
We recommend that you purchase a better Sticker.
View detail
Easy YOSHIMURACustom Part2
It was installed as Accent on a pure BlackWheel.
The installation itself was not that difficult as it was just a matter of stretching it along the pattern.
There is also a spare for a wrong tension, so I was able to tension it with plenty of time to spare.
I thought it was a little thin for an off-road motorcycle. I thought it was a little thin for an off-road motorcycle, but I think the body color RedBlack of RALLY50 tightens up the feet and gives an overall sense of high quality.
View detail
Newer homes are better.
I had a used MOTARDWheel that I had to replace the Tire, make it Tubeless, and even replace the Spoke for rust on the Spoke nipple, because I got to the point where I couldn't back out of it,
I've already decided to add Rim stripe to make it Beauty by the way.
Rim wounds were smoothed with BlueMagic. After that, degrease with Brakes cleaner.
As when I pasted MDFRim stripe before, I cut the entire base paper into strips and pasted them with FreeHand without using detergent because I wanted to avoid moisture as much as possible because of the hollow wounds.
After all, it was easy to paste Stripe while removing it.
The stripe is not smooth in some places due to some wounds, but since it is a used wheel, it can't be helped, so we have to put up with it.
I think the new home will be more Beauty, and I think it will also prevent Wound.
work process
1 Smoothing by gentle Gold genus polish.
2 Brakes cleaner is used to degrease and wipe down the surface three times to complete the surface preparation.
3 Cut Stripe into strips.
4 Position the Rim and attach the end about 2CM.
5 While holding there and peeling off the base paper, pull up the one to be positioned at an angle of about 30 degrees, and crimp it while holding it with the other hand.
Overlap the overlapping area by about 1.5 CM, press down again, and start.
Finally, Finish while inspecting for air bubbles and floaters while pressing down with the thumb.
Lately, I have been doing it this way without Gauge.
tools used
Compound and Gold polish, Brakes cleaner, Bent Scissors (Kyosho's well-known polycarbonate body for radio control - Scissors for cut) White Driving glove.
I felt that Takasago's ExcelRim was better for Off-Road's 15mmStripe because it didn't have any indentations or anything.
View detail
The rugged black wheel has a little bit of color, don't you think?
The vehicle is NT1100 White.
I think a delicate design is more suitable for this motorcycle than a sporty design,
We selected 4mm White.
The folded portion of the special affixing Gauge was slightly modified to fit the full circumference of the Rim.
Even though I am clumsy, it turned out beautifully, almost like it was supposed to.
It also comes with three Manufacturer Stickers, which is a nice touch. (I'm glad).
The secret is to use a thin detergent water as per the instructions, and it can be reapplied two or three times on the spot.
The large size is sturdy and durable, so there is no need to panic even if the laminate bends. Spare parts are also available in quantity.:It also says "1 Set of 2pc.
View detail
Easy and stylish!
Fashion starts from the feet up, as they say!
I was torn between Lime green and Titaniumium color, but I chose Titaniumium color because it does not look like OEM.
It is easy to apply and I think you can enjoy Fashion easily!
I used 6mm this time, but next time I would like to try 10mm for more impact!
It is strongly recommended to use MDFOEM's Sticking Gauge for Rim Stripe!
View detail
Easy to work with
I used this when I pasted Rim tape, and I was able to paste it without gapping. It is inexpensive and I think it is worth buying. View detail
Parenthesis better
The rim tape makes my feet look tighter and improves parenthesis. I love it. By carefully cleaning and degreasing the rim surface where the tape is attached, the tape adheres properly. The rim surface was attached properly by carefully cleaning and degreasing the rim surface. It took about an hour and a half from cleaning to completion, since it was my first time. I am worried about the durability, but it is cheap, so if it peels off, I will just put a new one on. It will be strange to peel off the old one, but.... View detail
Prevention of dust and water intrusion
It is the best protection for Tube as it prevents dust and water from penetrating. View detail
On the Grom JC92.
The Black one-color foil has quite an Impact.
However, Grom JC92 is Matte paint so some of it is peeling off and I have to repurchase.
Price is OK, as low as a joke.
View detail
easy to stick to
It is easy to apply because of its thickness and solid shape.
A misting spray with mild detergent and parts cleaner are required for installation. It is better to use a separate guide for more beautiful installation.
17in. is applied by overlapping each other by about 2 cm, so that the color and Logo are diagonal.
I thought the light reflection made it look like 7 colors, but it is actually Gradation.
Rim sticker is a Commendation by MDF
View detail
If you want to change the look of the Wheel area, this is the way to go.
The appearance around the Wheel and Tire will be Active.
The pasting process is not difficult at all. I have Repeat many times.
When working, don't forget to use a mist of diluted neutral detergent and Squeegee.
For those who want to easily change the look and feel of the product, this is Recommendation.
View detail
That's what I'm talking about!
That's what I'm talking about, YOSHIMURA!
It was perfect!
View detail
YOSHIMURARim sticker
The YOSHIMURARim sticker makes the undercarriage look so gorgeous. View detail