Reviews
Very grateful for bulk sales.
I bought a full set of Attacker model some years ago and
When I put it on my XG250 TRICKER, the impression was completely changed and tightened up.
I liked it very much.
A plastic part of the Tail cracked while driving on a forest road.
License Plate can no longer be installed.
I had to replace it with an Assy, so I bought it again.
It would be nice to be able to sell only the parts we need in bulk.
XG250 TRICKER has been discontinued for several years now, so I don't know how long they will carry it.
The Sticker on the Fork and Swing Arm is also in question, so I will try to repair it when the time comes.
The initial investment is high, but it is partially replaceable.
It is cosmetic in the sense that it can be used for a long time.
View detail
The appearance became Beauty.
I bought it because my previous Decal was faded and scratched and falling apart, and I didn't have Squeegee ready, just a misting spray and Dryer, which resulted in a lot of air bubbles, but I'm glad because it turned out Beauty from a distance.
The texture of the decal is very good, and the instruction manual is very thorough. The rest is up to the dexterity level and the quantity level.:Pair (for Left and Right) I think it will be done.
View detail
Attached to 2005 D TrackerSwing Arm
[How is it used?
Attached to a 2005 D TrackerSwing Arm.
I bought it because I wanted to increase the protection of the Swing Arm and the black part of the Swing Arm in terms of appearance, with a view to competing in the Motard race.
It has been in use for about four years.
Was the one you received as per Image?
As per Image. black and red Contrast is good and I felt that the appearance will be as I like.
We also felt that the Decal itself would provide good protection for the Swing Arm due to its thick wall.
Was the installation difficult?
It is not a difficult task if water pasting is done. If you have a Squeegee, you can paste on Beauty with a high probability.
If you do not do the above or cannot prepare the above, you need to concentrate on the application and carefully apply it so that air bubbles do not form.
How was your experience with it?
After about 4 years of use, Decal stuck firmly and protected the Swing Arm well without peeling.
The Decal itself is also sturdy and large enough that it has never been torn or damaged in any way.
Also, the appearance of the Large change was improved, and I was satisfied with the Large change without any color fading.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Point and hang of installation
sprinkling
wipe off the fog (about 300 ml empty Spray bottle) and neutral detergent and water.
A drop or two of neutral detergent is OK; add it to the misting cloth along with water. Fill the water to the brim.
Lightly dampen the paste surface and Decal with a mist wipe.
Then, paste them together. At this time, it is best to avoid air bubbles as much as possible, so that later work will be easier.
After pasting, the Decal is pressed down with a Squeegee, spatula, or Towel to expel the aqueous solution and air bubbles.
Then wait a little and you can paste it into Beauty.
View detail
It's hard to put up.
It was a little Large strange to put it because it is a place with many Curve.
It was surprisingly difficult to put it on while stretching with Dryer and needing soapy water.
Also, there was a spot where air bubbles entered even if it was fine when I put it on.
So you need to wait a little while after you put it on and see how it goes.
It is important to Check while you can reapply.
View detail
Purchased to attach the film.
Purchased for the purpose of attaching film to automotive window glass.
Anyway, the cost is good. The plastic spatula alone costs about 500 yen, but it has both Felt and plastic sides for wiping.
It was easy to use as it was reasonably pliable in terms of performance, and the Felt surface was perfect, so I didn't need to prepare a hand towel in one hand.
It's the finish of the film, but the cat hair got caught in the mistake of the worker.
View detail
Good design, installation and function
This product is purchased on a case-by-case basis, and the change in the appearance of the motorcycle after it is installed is the result of I'm looking forward to it It's AllKit and I should have purchased it from the beginning But I think this is the last time I will buy it I am happy with it
View detail
Good design, function and installation
I have purchased the product several times now, and every time I have the opportunity to install it The image of the motorcycle is changed from yellow to blue I feel like I did It feels like it's made in my favorite color I am looking forward to touring again Installation was a breeze View detail
Graphic, shape and details are OK
The color, Graphic, shape and details are OK It was also easy to stick it on After that, the shape of the former motorcycle was replaced more than I thought View detail
Design/manufacturer products OK
I bought these last time and they have changed the feel of my motorcycle The shapability and details are well made so it was easy to apply it I would like to purchase another part of the product View detail
Fits: YAMAHA YZ450F
Just Parenthesis good
Design is perfect! If you wear it, you'll have a great United States rash
It is quite difficult to attach the seal, but I think the cause is in the shape of the exterior and the Decal side The material of the seal does not stretch too much by heat, so it is easy to apply the seal without anxiety It is available I used a high pressure car wash once, but there is no atmosphere of stripping off
View detail
I put it up
There is an Instruction Manual, but the actual work is quite difficult to do
Rear cowl is divided into two parts from the center, and the center part is overlapped It will be a paste
It was very difficult to finish this stacked area and the treatment and finishing of the area near the footpeg
In my case, one of the tips was stretched out because I was applying hot air to it while I was finishing it, so I had to use a different method to make it work under the Seat I removed the UnpaintingCover and cut it a bit
My personal work time was about four hours
We use an air-compression type horticultural sprayer
It's safer to buy a dedicated Squeegee
Anyway, it takes a lot of patience and time, but you'll be happy with the finished product (Lol)
The finished product is much more flashy than it looks in the product image
Will the rim of the rim be able to survive the winter without peeling off?
That's what I'm concerned about
By the way, the Matte paint part certainly sticks without any problems, so don't worry if you're worried about it
View detail
I haven't put it up yet
I think this is the only Decal for the CYGNUSX Type 5 at present
What was different from my expectation was that the Application Sheet, which will be used to align and protect the printed surface as well, has been added to the printed surface It's what didn't happen
If you don't have a Squeegee, misting or degreaser, you can't get a scratch on the printed surface Use Squeegee and provide your own misting equipment Parts cleaner can be substituted for degreaser
Dryer is also a must
As I watched the video, I had the impression that it was quite difficult, so you may not be able to put it up beautifully unless you have some experience with it It is not
Also, depending on the color, the side cover is Matte painted, but I asked MDF It can be applied properly where The answer is that it is
View detail
Red likes me
Though I liked the actual thing that I received because I liked it more than I thought, the thickness is 1 compared to NORMAL / Since there are only 3, Cost performance is low scoring.
Pasting was done with two friends with friends, but it is quite difficult to finish without complicated surfaces of Shroud without Wrinkle.
With my skill, I felt it was impossible to work alone.
YouTubeetc how to paste. We advise you to do the work firmly and work hard without spending time.
View detail
Thin but good adhesion and Fitting
【What made you decide the purchase?】 I bought a new Helmet, but I really wanted a graphic model, but I made it a Solid model at a price. So, as a result of considering how Lime green can not be reflected in Helmet, I thought that it would be possible to cut and paste Ninja 250 and klx's graphic kit!.
【How was it actually used?】 Again pasting is difficult, but there is satisfaction in the completion of handmade GraphicHelmet and also attachment attachment.
【Was it difficult to install? (Hard parts case)】 Because it was made thinner, it is a sharp Cutter, I put thick paper on the bottom and cut it. Surprisingly Quantity : Pair (for Left and Right) It was difficult to Cut symmetrically.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Paste the middle first, gradually stick it to Right, Left. Warm up the finish with Dryer and firmly stick it. However, be careful as it will not be good for Helmet if you make it too hot.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) ]
[Is there anything I was disappointed about?] It was a bit disappointing that the space between Green and Black was slightly uneven.
【Hope for Manufacturer - Please tell me if there are any improvement points】 I'm happy if you pick it up at Manufacturer, which is a violent sticking Graphic for Motorcycle to Helmet.
【Have you compared items?】 None
View detail
Fits: YAMAHA WR250X, YAMAHA WR250X
Sharp design is good!
Since I wanted to finish planning to make it Yamaha Inter Color from before purchasing the car body, I wanted to finish it cool with OEM, so I dared not to paste the two places of Fork Guard and Swingarm.
By the way, the White part of Headlight cowl is sticking another Manufacturer object instead of MDF's Decal (There is no Decal of this White part in MDF)
■ Point of work
- There is no problem if you proceed according to the polite Instruction Manual.
- It is NG who blows Parts cleaner to Large quantity in Plastic part, Tissueetc. OK in a small amount.
- Start with small parts to get used to Small and make it easier to postpone the complicated parts and the bigger parts of the area. (In particular, it is better to put it as far as the curved surface part, Light cowl ⇒ Tail cowl ⇒ Side cover ⇒ FFender ⇒ Shroud)
- If there is no soft Squeegee and Dryer at the tip, the curved part can not be pasted on Beauty first.
- Immediately after sticking, raining, car wash, waxing etc etc etc etc. Be careful as it may be hurt by.
- It is desirable to leave it for 2 to 3 days until it is completely fixed (In the meantime, although it stretched and pasted part, it returns to original)
○ good point
- I am safe even if the description of Instruction Manual is polite for the first time.
- Decal's thickness is thinner than imagined Design for emphasis on ease of pasting.
- High convenience that you can easily make Makeover by preference.
Attention point
- It is a feature for WR, the tip of the FFenderCenter part is very thin and it is Dustclothetc. Danger in hanging on hook Large.
- Depending on the location, there are several parts that do not fit slightly with Body line.
- Decal Print at several places in the end part Gap (?) Yes.
- "MDF" The logo of too many impressions (In particular, it is better not to have Logo of Shroud part)
Faded etc etc. Although the durability performance will be verified in the future, if you want a greed a bit more price is cheap, I want a design variation.
In addition to the color change, for example, if more than one DesignPattern is prepared at one place, I think that further combination can give Originality and I think purchasing willingness will rise even more than now. If you like the design that was prepared from the beginning, this product which can easily change the image is considered to be very useful and highly satisfactory as the product value.
Although I wrote various things, it was a very enjoyable time to imagine a complete image of my car before purchasing!
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
R25 Graphic change
I think that COSPA is good even though it is a high Sticker
"Japan Spec of r25. Decal Is not it plain? "
"There's no one on this?"
I bought it if I fucked it
It's rich!
There is quite a gap as contents, so I can only say that I should try hard
I pasted it with water.
Sticker I think that I am pretty accustomed, but it took me three hours carefully. I already do it. ('A`)
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker 125
Instead of painting
MOTARD's exterior paint is difficult, so I put it on Dress-up.
I am happy to sell Rose for each part.
Although a little value is stretched, quality is no doubt.
Pasting Instruction Manual is attached and it takes some trouble but if you paste it according to the procedure it is finished like Decal that is affixed at the time of shipping the new car.
View detail
Since he wanted the Helmet of graphic specification and the Design of the Electronic flash was smart, an order with a trial was placed. attachment thinks that it will work turning a blind eye to some a Gap and cellular mixing, and Wrinkles with it bei
Since he wanted the Helmet of graphic specification and the Design of the Electronic flash was smart, an order with a trial was placed.
attachment thinks that it will work turning a blind eye to some a Gap and cellular mixing, and Wrinkles with it being slowgoing, although a considerable bone is likely to break.
Since an attachment Service in a Manufacturer can be used if the expenses around 7000 yen are incurred by the
(by Manufacturer direct order) addition, the troublesome person of using there may also be good.
View detail
Although it does not go up to a bad place, a form is an interval plug delicately to a pure Side cover. Since it can cut easily with the Scissorses, it does not become pain! It was that about 2 cm of end pieces overflow, and about [ wh
Although it does not go up to a bad place, a form is an interval plug delicately to a pure Side cover.
Since it can cut easily with the
Scissorses, it does not become pain! It was that about 2 cm of
end pieces overflow, and about [ whose an opening is / just before / small ].
appearance satisfaction -- * -- four ^ ^
View detail
No. 1 was serious by the Graphic kit attached until now. A No. 1 mistake was also made. It is moved to tears. Although the Muffler side was able to be stuck well, the Side-cowl side already tatters. .... in which pasting also of als
No. 1 was serious by the Graphic kit attached until now.
A
No. 1 mistake was also made.
It is moved to tears.
Although the
Muffler side was able to be stuck well, the Side-cowl side already tatters.
.... in which pasting also of also being divided into two is well impossible by the cause of failure, and distortion enters considerably and in which air is also full of failures at entering
View detail