Reviews
Required Option
This is a required Option when purchasing Carrier.
It would be nice if it could be Carrier's Standard Equipment product if possible.
View detail
Load capacity has been increased.
I bought it to carry my backpack, and the extra width of the carrier makes it more stable and gives me more room to sit. View detail
cool and solid
I installed Kohken bleeder bolt on Brembo 19 MCS brake master cylinder, it fit very well and solid. I've chosen titanium coast treatment, it look very cool. View detail
Bleeder Bolt for Nisshin Caliper MASTER
The OEMBleeder Bolt had deteriorated, so we replaced it with this Bleeder Bolt made of Stainless Steel.
Material:It is Stainless Steel, so the weight is the same as OEM, but I am very satisfied with the detailing, rust resistance, and black color.
I had also purchased a ZETA Titaniumium breeder bolt before buying this product, but later realized the existence of this product and repurchased it.
Material in terms of price:It is the same as Titanium, but I was attracted to the fact that it is black, the same color as Caliper, so I had to use a Titaniumium breeder bolt.
View detail
Replacement of Bleeder Bolt on brembo Master Cylinder
Before the CORSA CORSA Corta OEM Brembo Master Cylinder bolt rusts away, this Material:I replaced it with a Stainless SteelBleeder Bolt.
Common Material:I was looking for something as quiet as possible, because Titanium and other materials would be Gold shiny, and I found this BlackXCoat, and the price was very reasonable.:I was hesitant to buy it because it was not much different from Titanium, but I had some points saved up.
Compared to the OEMBleeder Bolt, the finish of the Screw section and seat surface is very carefully done and the quality is very high.
However, this product is Material:Stainless Steel, priced at Material:It is about the same as the Titanium one, so I guess it comes down to weight or Black Finishing.
That said, the difference in weight is only 2 to 3 g, so it may be better to select a product based on appearance according to one's own preferences.
Black on Titanium may require special processing? Black on Titanium may require special processing.
View detail
product is good
I bought an African twin plastic top box from 16-19 to install it on the Hunter Curve. The rubber bushing is installed on the vehicle so that it can act as a damper, and rather than being firmly fixed, it is installed with enough space to buffer to some extent. So, even with the top box attached, the fishtail phenomenon does not seem to be severe, and it shakes with the load to some extent, so I feel that it is easy to operate and protect the load. -------------------------------------------------- -------- I bought an African Twin Plastic Top Box in Hunter Curve, which is available until the 16-19 years. It is installed in the vehicle so that the rubber bushing can act as a damper, so that it is installed so that it is fully buffered rather than firmly fixed. So even when the top box is equipped, the fish tail is not severe, and it is shaken with the load, so it is easy to protect the loading and protection of the operation. Powered by Google Translator View detail
Required for Tandem
Perfect for Tandem when used in combination with OEMPillion Seat View detail
Good Quality & Packaging
The item is fit in my radial brake. Good quality and was packed properly. I like the engrave brand letter on the bolt. The item is durable. View detail
Match the color of Caliper
Since I replaced it with brembo black, I replaced it with this one for color matching and rust prevention.
The quality is not a problem at all because it is a Koken Brand, and I felt that the Wrench to be used is even better because it becomes 10mm from 11mm.
The material is Stainless Steel, so be careful not to over-tighten.
View detail
Higher quality than brembo OEM
The motivation for the introduction was iron Bleeder Bolt corrosion on the NORMALRear caliper.
My regular shop noticed corrosion during vehicle inspection maintenance and replaced the OEM product, but there was no corrosion on the Front and it was untouched.
I have been using 40mm pitch brembo universal casting for the Front (I'm the second generation and I've been using it for 7 years, and the first generation Brembo caliper lasted 36,000km for 17 years). The purpose is to extend the life of the caliper.
The ability to convert from the rarely used brembo OEM 7/16Inch (11.12mm) size to the frequently used 10mm size is another motivation.
The texture and structure are both good, etc., so we'd like to expand to the rear caliper as well.
View detail