Reviews
perfectly (suited)
Perfect for your local Number!
The number is small, so it is not likely to be bent even if it was there much.
It is safe.
I'm putting up the Seal of the Shrine Amulet.
View detail
To one point!
I put it on because I wanted a change in appearance. View detail
with Reflector
Purchased because of the Fender Eliminator.
The Reflector is convenient because it can be installed along with the Number, since it would be poorly maintained without the Reflector.
The product itself is thick and sturdy, so it is unlikely to be bent only at the reflector attachment point when it is caught on the cover.
I think the price is a little high, but the color is good and the rigidity seems high, so it is not bad.
View detail
Casual Accent but satisfying!
Balance of price and texture is good.
I wanted to match the color of the car body, so I am satisfied.
View detail
Ideal for crime prevention.
This is no longer an exquisite product.
The combination of anti-tinkering Torx bolt and anti-loosening Nut is kind.
The design is simple and the color line nap is abundant.
View detail
It has a sense of luxury.
Installed on PCX160.
It is quite luxurious.
Reflector is also satisfactory with good design.
View detail
Protection of SR400 License Plate.
I feel that the License Plate does not shake so much when idling. Also, I feel that the License Plate Holder and the License Plate are firmly fixed. View detail
Security, looks, expandability
I wanted to include a Cali Sticker Plate, so I attached it to the local Number with the company's Torque screw 25mm and 6M× diameter 18mm× thickness 3mm Spacer, which is sold separately.
Note that the Wrench for the Torx screw (sold separately) has only one tinkering hole.
View detail
Hara1 Local Number only
We purchased this for our Hara1 local Number.
Fit the local Number with no problem.
We recommend that you measure the dimensions of your local number in advance.
Width is as in previous Impression.
View detail
Gorgeous because of its color!
We replaced it incidentally when adding a Hook around the License Plate area.
The Torque bolt has a flat plate screw head, low volume, and a thin aluminum tray for a clean look. The aluminum tray is also thinner and looks more stylish, whereas a normal bolt looks rugged.
You will need a T30 Torque to install it, but it is not included with the product. It would be a waste to buy it just to install this, so we recommend checking to see if T30 is available beforehand.
View detail
Anti-theft and dress-up
I use it on all three of my motorcycles. It is a good anti-theft measure and also has a dress-up effect. Highly recommended. View detail
For vehicles registered as Class 2.
I installed this on my class 2 registered VINODELUXE and I think it is a must have for a class 2 registered moped. I am glad that the Triangle Mark Sticker is included so I didn't have to buy a new one.
The finish on the corners of the Holder is not good. I was also concerned about the weight of the Holder itself, but it might be good for durability.
View detail
The Bolt on the License Plate was about to rust.
The bolt that attaches the number seemed to rust, so we changed it to this TorqueTaperBolt & Nut Set.
I chose the color Silver so that it wouldn't stand out too much, and I'm glad I did, because it looks OEM-like, just as I wanted.
And, since our vehicle has a driver's recorder bracket that is co-tightened, the bolt length was a little longer than other products, but the thickness of the bracket was just barely sufficient to allow installation.
I have no problem with normal installation, but would have appreciated another 2mm or so longer.
The bolt installed on the car at the time of delivery is prone to rust, and it has a large area to prevent tampering? The Bolt installed on the car at the time of delivery is susceptible to rust and tampering, and has a large area to suppress the Number, so depending on the type of car, such as a single cylinder, the Number may be less likely to crack due to vibration? It may be.
View detail
Used instead of Fender
Fender is cut and used in Fender city because it splashes a lot.
There is a big difference between having it and not having it.
View detail
A Little Fashion
Since OEM Bolt is lame (lol),,,, it is a bit Fashion. View detail
Installation in conjunction with RearFender cut
CROSS CUBFJ60 I installed this product because I lost the triangular mark due to the rear end cut of the Rear Fender of the "Rear Fender". View detail
Special shape
It is sufficient as a PlateHolder.
I can put a triangular Mark on the moped type 2 where it sticks out.
View detail
Simple
The back of the number has been refreshed. View detail
Just fit!
I was looking for a Hara2 local Number and could not find one that fits the rectangular Type. I love the texture of this purchase! If it were a little more cost-effective, I would give it 5 stars, although the All rating is maxed out. View detail
For protection of Number and prevention of mud splashes.
The expected effect was to prevent mud splashes during Fender EliminatorSpec.
This part is installed in such a way that it opens outward from the back, so that the smallest possible area can be used to achieve the largest possible effect. The impression was very natural! When I checked the reverse side of the car after driving, I found that the mud splashes were properly controlled, and there were no splatter marks on the surface of the number.
Nutty Off forest roads and rough weather, even OEMFender can't prevent bounce-offs, just as we expected.
It is not bad, but it is heavy because it is steel and I wonder if it is my installation problem. I have noticed a chattering sound similar to that of the Off car's Under Guard at certain RPMs when the car is first warmed up.
That said, there are no other parts of this type that can be found anywhere else, making it a rare and precious commodity, and it is also extremely easy and simple to install, making it an easy and highly recommended part.
View detail