Reviews
Fits: Others , HONDA 400X, HONDA ADV150, HONDA CB1000, HONDA CB1000, HONDA CB1000SF, HONDA CB1100, HONDA CB1100, HONDA CB1100CA, HONDA CB1100NA, HONDA CB1100SF, HONDA CB1100SF, HONDA CB1300SUPERFOUR, HONDA CB250F, HONDA CB250R, HONDA CB250R, HONDA CB300F, HONDA CB300F, HONDA CB300F, HONDA CB300R
Number Protection
I installed it to prevent the Number from bending. So far, it works well because it does not bend when it hits.
Also, it's very heavy.
View detail
Fits: その他
Exclusive products are ultimately safer than Universal Products
The Ceramic resistor part of the LEDNumberSIDEBlinker made by ACTIVE was damaged and became a high flasher, so I bought it for repair. I am glad to know that I can install it easily! I would be happy if ACTIVE would continue to sell Repair Parts. View detail
To protect the license plate.
[How is it used?
I searched for a License Plate Holder on Webike to protect my SEROW225WE License Plate. I was looking for the cheapest product and came across KITACO's product.
How was your experience with it?
The appearance is that of steel with plating, so the Material:If you compare it with the products that are Anodized Treatment for each color in Aluminum. Cheapness." cannot be hidden.
However, the motive for purchasing License Plate protection that bends every time I go out to play in the mountains." Therefore, since they are going to be bent anyway, Cost is more important than texture.
How did it compare to other products?
As I said above. "Cheapish" The price is actually cheap, so there is nothing to be done about it.
Material of the same thickness, perhaps due to the material of steel:It is a little more rigid than the Aluminum product, and so far the License Plate has not bent.
[Points to note]
The product is made of steel with plating treatment, so it will eventually be rusted if scratched.
Even without Wound, Rust may be unavoidable depending on the environment, so it may be better to protect it with Wax or similar.
There is a possibility that you may get hurt if you handle it roughly with your bare hands. [Color] I sprayed ClearSpray.
Other items that would be helpful
The deciding factor in the purchase
Cheapness, that's what it's all about.
In my case. "the expendables" However, if you are looking for texture, Material:Aluminum and Material:I think you will have less post-purchase regret if you consider Carbon's other products.
【Included Parts:presence or absence】.
Only one Plate is available.
Simple, low price, just the right product for me.
[ITEMS TO BUY TOGETHER
The existing Bolt can be used to install the License Plate with no problem, but it may be a good idea to add an Aluminum Collar or CoolBolt (if you are in an area where theft is common, you may want to consider an anti-theft Bolt).
Opinions and requests to Manufacturer.
We look forward to a long-lasting Lineup for Cost-conscious Users.
View detail
Bolt part to Custom
[How is it used?
License Plate Bolt to Custom
Was the one you received as per Image?
Yes, it was exactly what I expected.
How was your experience with it?
Bolt section is now custom made.
[Points to note] It takes a little time to install.
How did it compare to other products?
No comparison, so no.
Other items that would be helpful
None
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
When installing on CT110 HUNTER CUB, it seems to be easier to loosen the Rear Reflector, though.
View detail
![PREMIUM ZONE License Plate HolderQuantity:Set [M6]](https://img.webike-cdn.net/catalogue/images/15903/91947_1_TS.jpg)
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
For One point in the License Plate Department!
I purchased it as a one point accent for the license plate section, and as a result of installation, the license plate section looks tighter! View detail
Fits: Others Universal
License Plate Reinforcement
I was riding my CB1300SF and was rear-ended by a car and although I did not fall over, the License Plate was bent. I bought a Plate Stabilizer and installed it to avoid any more rear-end collisions! View detail
The License Plate is bent, so it is reinforced with a License Plate Holder!
I was looking for an inexpensive License Plate Holder before the License Plate bent into a squishy mess, and I found KITACO's License Plate Holder!
I like it because of its simple design and good texture!
View detail
Slight appearance change
I was looking for a Case to put my CALI certificate in and happened to come across it in a search and it was cheap, so I bought it.
I didn't like the position of the Sticker on the local number, so I'm glad I chose this one.
It is a product that is only for appearance, but I think this kind of product is also interesting and White.
View detail
Fits: HARLEY-DAVIDSON FLFB, HARLEY-DAVIDSON FLSL, HARLEY-DAVIDSON FXBB
Number bracket kit
Refreshing around the Number.
Parenthesis I got better.
View detail
Fits: Others Universal
For License Plate protection
I purchased this to protect the License Plate. As other reviewers have mentioned, the License PlateBody does not fit into the groove of the Frame perfectly. I don't know if this is the reason for the cushion material, but I think the PlateBody will have to be lifted a little. I think that people who purchase this type of frame probably want to fit the license plate into the groove of the frame. If you cannot fit the license plate into the groove, we recommend you to purchase the type without groove. View detail
Fits: Others Universal
Note that Reflector is easily removed.
[How is it used?
I wanted to refreshing around the Rear of KDX220SR during Restore, so I set the Fender EliminatorSpec. to be used, but it was too refreshing and the Number seemed to bend easily.
Did you receive the item as per the Image?
butchered Material:It is a simple product made of aluminum with little assertiveness, yet it is a functional product that seems to work well and is exactly as shown in the Image.
Was it difficult to install?
Once the License Plate is removed from the vehicle, this product is inserted into the back of the License Plate and the work is completed.
BoltQuantity:Easy Custom that only requires 2pcs removal and installation to finish the work. (?) It is
How did you like it?
I installed it on a vehicle that vibrates a lot, but so far I haven't noticed any loose or cracked troubles.
Was "Included Parts:" attached?
Reflector type was purchased, so Reflector Plate, UrethaneTape for vibration reduction, Bolt&NutQuantity for installation.:2pcs BlackAluminumBolt colorQuantity:2pc. Set was included in the package.
Were there any disappointments?
As mentioned in the Title, the Reflector was removed from the Body during the installation process.
Looking at the Mounting Base, there were no claws for mounting and no trace of adhesive or double-sided tape, so it was a wonder it was still attached.
Probably if it had not been removed by this Timing, it would have come off during driving, so I wonder if I am lucky or not... I glued it with RubberBond for vibration resistance, and so far it has not come off.
Other items that would be helpful
Point and hang of installation
Since there is room in the large size of the hole for fixing the bolt, if you install the bolt properly, the bolt will be slanted or the bolt will be too large for the quantity of the bolt.:Pair (for Left and Right) If you are concerned about this, please check the upper and lower Quantities.:Pair (for Left and Right) Install it while watching the Balance of the
[Availability and clarity of the Instruction Manual
This easy-to-understand product also comes with an Instruction Manual, which is typical of Daytona's products in terms of ease of understanding.
[Notes]
As I mentioned above, Reflector is easy to remove. (Is it an individual difference?) I think it would be better to reattach it firmly with double-sided tape or Bondetc. to avoid a sad ending.
[ITEMS TO BUY TOGETHER
Nothing in particular, this product is all that is needed to complete the work.
However, it may be a good idea to purchase double-sided tape or bond etc. if you do not have them on hand to prevent the reflector from falling off.
[Opinions and requests to Manufacturer
Please make sure to take measures to prevent Reflector from falling off.
A few more color variations would be even better.
View detail
Tanax Moto fizz plate hook4
I purchased this product to install Side Back on my BirdCity125.
I think the quality is good and the cosmetics are good.
This is a product of Recommendation to Scooter.
View detail
Low-profile License Plate Base
[How is it used?
If you have a Fender Eliminator, there is a risk that the License Plate may bend, so we purchased a base plate as reinforcement.
Was the one you received as per Image?
The quality is not bad, but since it is FRP, strength needs to be taken into account to a certain extent.
Was the installation difficult?
It is easy to fix by simply clamping it onto the License Plate.
How was your experience with it?
Quantity:Pair (for Left and Right) The reverse side is attached with Carbon Seat, and the other side is attached with Carbon Seat. [Color] Clear is blown on it so it seems to be easy to clean.
[Was there anything that disappointed you?
It is thinner than you might imagine, so it is likely to be cracked by a Damage that hits it. It is a reinforcement to prevent the License Plate from bending.
View detail
For License Plate protection in off-road driving
good point
・ Corresponding to Notification No. 1266 of the Ministry of Land, Infrastructure, Transport and Tourism.
Looks pretty sturdy.
A bad point
Not much if you can justify the price.
For License Plate protection in off-road driving
Stainless bolt and aluminum spacer are included.
I was able to co-tighten with KIJIMARearReflectorFrame.
Please let me know if you use the Fender Eliminator Kit and run off-road.
View detail
Fits: Others Universal
Refreshing
I bought it because the Number was bent without me noticing.
Black on MONKEY125.
I think it is good that it is slightly larger than a number, not too conspicuous and reflecting.
It is too short for the included Screw when I put on the Sponge to prevent resonance.
View detail
Fits: Others Universal
Attached Screw is too short.
MT-25, but the Screw is too short when I put Sponge to prevent resonance.
I have put a Screw lock on it to stop it, but we'll see how it goes.
Others are satisfied.
I think it is light, meatless, and well designed.
View detail
![PREMIUM ZONE License Plate Holder Set [M6]](https://img.webike-cdn.net/catalogue/images/15903/91945_1_TS.jpg)
Fits: SUZUKI GSX-S750, HONDA CBR500R, YAMAHA YZF-R3, HONDA CB500X, HONDA CB150R, HONDA CB300R, YAMAHA YZF-R25, YAMAHA XSR900, SUZUKI GSX250R, SUZUKI GSX1300 HAYABUSA, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-R125, KAWASAKI VERSYS-X 250, HONDA PCX125, HONDA NC750X, HONDA CBR650R, HONDA CBR650R, HONDA CBR400R, HONDA CB650R
Red is good for PinkNumber
Purchased Red for my moped2 PinkNumber because I thought it was a good choice for my moped2 PinkNumber.
I am satisfied with it just as I imagined.
View detail
Gorgeous because of its color!
We replaced it incidentally when adding a Hook around the License Plate area.
The Torque bolt has a flat plate screw head, low volume, and a thin aluminum tray for a clean look. The aluminum tray is also thinner and looks more stylish, whereas a normal bolt looks rugged.
You will need a T30 Torque to install it, but it is not included with the product. It would be a waste to buy it just to install this, so we recommend checking to see if T30 is available beforehand.
View detail
It's normal
Can be installed normally.
However, I think it would be troublesome to clean it if it gets dirty.
View detail
Fits: Others Universal
in a fashionable way
[How is it used?
Installed on Yamaha's WR155R.
Fender Eliminator is installed, and since GIVI Bracket is installed, the Blinker is relocated to the Number.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is co-tightened with Number, so it can be installed immediately.
The Frame is attached to the Sponge like a vibration, but the Number is placed on top of the Sponge, so the Number is not completely covered by the Frame, but is attached to the Image as if it is floating.
It does not seem to offer that much protection in the event of a fall.
How was your experience with it?
Stylish and good.
Reflector is also included, so no need to retrofit. Good shape.
[Included Parts:were they on?
Sponge
[Was there anything that disappointed you?
I want to feel more protected!
View detail