Reviews
Because it is a genuine product, it fits well and looks neat.
I looked into other tank pads and eventually decided on Suzuki's genuine pads. There is no particular reason, I just heard that it is easy to attach. This is a photo attached after delivery. Because it was the right size, even someone like me was able to attach it easily. I haven't driven it yet, but I'm very satisfied. View detail
poor in cost performance
Tank Pad was attached before it was scratched because of the large Tank surface.
I think it is well made and thick because it is OEM.
I don't think it would detract from the design of the vehicle.
It is difficult to put it on straight because of its wide surface.
Be careful not to stretch slowly from the edges, otherwise air can easily enter.
View detail
Even though it is made overseas, it is an OEMOP, so there is no need to worry about quality
There are cheaper ones with the same design available at a certain Site, but I chose this one because it is made in the same foreign country but OEMOP, so I did not have to worry about the quality. I am satisfied with the result. However, since I have had trouble getting the center out of any Tank Pad, I wish this one, which is an OEMOP, at least had a guide for attaching it. View detail
Tank Pad
Satisfactory, but not great value for money. View detail
Tank Pad
The price is high because it is an OEM product. It is normal. View detail
Parenthesis good!
I like Largeisa and Design very much.
The thickness is about 3mm, so I think the Body can be well protected.
There is no backing paper included for positioning the paste, so you have to measure and paste it yourself. It would be great if a backing paper was included.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S750, SUZUKI GSR250, SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI DL1000 V-STROM650XT, SUZUKI DL1000 V-STROM650, SUZUKI DL1000 V-STROM1000, SUZUKI DL1000 V-STROM1000XT, SUZUKI DL1000 V-STROM800DE, SUZUKI GSX-8S, SUZUKI SV650X, SUZUKI SV650
Unique texture of OEM
Before pasting, it looked very small, but when it is actually pasted
Just size, I felt it was quintessential OEM.
The seal surface is made of aluminum sheet and is quite hard and firm. Once the position of the seal is determined, it can be attached relatively easily.
The front edge of the Seat is effective as an anti-scratch measure since the Zipperetc. of the Wear hits it.
View detail
Just for looks?
When I saw the product photo, I thought it was a Rubber quality product, but when I looked at it, it was a little thicker Sticker. The sticker is applied by spraying it with diluted neutral detergent, and there are no problems with air removal or positioning. View detail
Suzuki tank pad
Item well received.well packed.very satisfied.my second purchase.many more to come.highky recommend.thank you webike.awsome job View detail
Pasting is easy.
The adhesive was strong and easy to apply.
Since the adhesive strength is reduced in cold weather, it is recommended to run lightly or warm up the tank with Idling before installation.
I don't know how durable it is yet, but the Guard range is Large size.
Since it is an OEMOption, it is a Recommendation.
View detail
It's something you don't have to ….
It's something I could do without, but it looks tighter.
I put it on when I took delivery of the Motorcycle, so I can't compare its effectiveness in preventing slipping compared to when I didn't put it on.
When asked if they are non-slip when worn, I can only say that I don't expect them to function that way….
on (for) our side (side) The "look as the most Large effect, so I think it is effective.
At the same time, I also added a Tank Pad, but this one could have been more or less….
View detail
CoolDesign
To protect the Tank from Wound because it is the part where the Jacket and Pants hit.
It is required to be installed. ?? It is also cool that it has the name of the car model.
Pad is divided into 3 parts, so don't Gap when pasting.
We need to be careful.
View detail
Tank Protection
Film seems to be thick and protective.
The tip of the Seat is OK if you press it against the R of the Tank while using a hot gun.
Finish by stretching with a spatula in a radial pattern so that there are no air or detergent residues.
The film may look white immediately after pasting, but after one night, it settles down and becomes transparent.
View detail
OEMTank Pad
It is an ordinary Tank Pad.
It was easy to install and stick straight on.
View detail
no problem
It was very easy to put it up if I followed the Instruction Manual.
Design is also satisfactory.
View detail
GSX-8S
I was able to install it on a GSX-8S Tank without any problems. View detail
Self-assertion is a Large thing.
There is a gap between the pads, but it does not affect the tank protection. View detail
The texture is good
The texture and feel are OEM, matching that of Cowl. The Silicon one made by another company would be a safer choice for those who drive on circuits as well. The installation was done by Red Baron, but the factory manager told me that the installation was very difficult and that I should rest for 24 hours after the installation. Overall, I give it 4 stars. View detail
Good shape!
Masking tape was used to come to the center
Degreasing of the sticking area was also performed.
It's been two months and no peeling at all.
Texture is very good
A little expensive.
View detail
I can't get it to stick.
Even though I applied it as described, it still left a white residue. In addition, the bottom part does not fit the curvature well. In the end, I peeled it off and threw it away.
Ask Shop to install this product.
View detail