Reviews
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
Used for CUB
[How is it used?
CUB's fuel tank cap was destroyed, so this is used
Was the one you received as per Image?
It was as per Image and there were no problems.
Was the installation difficult?
Installation accuracy is good, and it can be used with the same degree of force as the OEM.
It's a pontoon.
How was your experience with it?
Since it is thinner than the OEMTank cap, Fittingetc. can be installed without worrying about anything.
However, as is the case with OEM, there is a part where it feels a little difficult to turn a slightly thinner cap than OEM in order to turn a slightly more reluctant tank cap.
[Was there anything that disappointed you?
Not particularly
I think this is cosier than looking for a used one with Key cylinder.
View detail
Rusted and replaced
I purchased the same product a long time ago, but it rusted due to neglect, so I purchased the same one from here this time. Rust in the tank is unavoidable, but the exterior is clean and the quality of the product is good enough. View detail
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
The quality is not good
It's thin and cheap, it's going to cut my hand and Gasoline is going to leak.
If you want to pay $1,000 for this, you might as well buy an OEM keyless Cap for $1,500.
View detail
just support, not strap like shown in ALL of them pictures, a bit misleading since there isnt any picture of just the plate
its just the support plate, not the bracket like shown in ALL of them pictures, a bit misleading since there isnt any picture of just the plate. though it looks good qality its not what I need. View detail
Just like the CT110!
Really wanted to attach the old CT sub tank to my new trail and this was the best solution I had found at the time. In practice is really flops around alot on the dirt trails and I have seen too many posts of it snapping off the mount on the bike due to the weight of the sup tank. Needs to mount to more than one location. It will work totally fine if you never take the bike off road. View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
Normal use
I used it to install a Gorilla tank on my MONKEY.
Back side of Tank (Bolt tightening point) The OEM was one piece, but this is a split type, but no problem at all.
If I had to venture a guess, I would say that if you carry a tank with a split bush attached, the bush may come off.
There is some BALI, but not enough to be bothersome.
The OEM was quite soggy and may be replaced if there is an opportunity to remove the Tank.
View detail
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
The cap on the gas tank on the Super Cab
The cap on the gas tank on the Super Cab Custom fit without problems. It twists very tightly and tightly, which makes it possible not to spoil gasoline. But there is no key - pay attention to this if it matters to you.
The photo shows the installed cover on the moped and also a comparison with the old original cover with a key.
The quality is average, but the price is also inexpensive. -------------------------------------------------- -------- The lid on the gas tank on the Super Caster Caster approached without problems. Spins very tight and hard, which makes it possible not to spoil gasoline. But there is no key - pay attention to it if it is important for you.
In the photo installed cover on the moped and also comparison with the old original cover with the key.
Quality is average, but also price is cheap.
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
It's enough
You don't need to be concerned about OEM parts if they are this cheap, and you can install and use them without any problems. View detail
Fits: HONDA monkey, HONDA monkey
It can be used without loss with OEM. Cospa ◎.
I used this one on a 6V early GORILLA.
This is helpful because some OEM Parts have already been discontinued.
Quality is also OEM and no loss.
It's cosy.
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
It can be used without loss with OEM. Cospa ◎.
I used this one on a 6V early GORILLA.
This is helpful because some OEM Parts have already been discontinued.
Quality is also OEM and no loss.
It's cosy.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I was injured on Edge.
This is a lousy product. I cut my finger on the edge when I turned the device with my bare hand. I have a lawsuit on my hands. View detail
Fits: HONDA MONKEY, HONDA GORILLA
I didn't Match Tank.
I'm not sure if this is a good idea or not. View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
Used for assembly from Frame
It was a pain in the ass to find an OEM, so I used this one. View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
You can't see it, so this is enough.
It is a part that is hidden in the tank, so I personally think it is possible to use Other Brand Product.
Best of all, the prices are reasonable!
View detail
I put it on my 6VGORILLA.
It went straight to 6VGORILLA.
Care must be taken when installing the Fuel Cock.
Don't tighten too much with Wrench.
The packing seems to be shredded.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I was wondering if the door wouldn't lock
Purchased to install in the China Tank
I saw the Cap shape that I was previously hooked on and ordered it
Size is good, but it's not so bad
I can't lock my keys
Hmm?
It's the same shape, but..
You can push in quite a bit from the top and turn the key while lowering the front down
We have a lock on it
Is it because Rubber is hard?
I'm hoping that it will be easier to lock if it's fitted
View detail
Fits: HONDA APE 50, HONDA GORILLA, HONDA MONKEY
It's fine!
Order to put a Chinese Tank on it
I haven't fitted the front mount yet
The rear mount was the right size
Isn't that fine!
View detail
Sub tank！
It was installed in DAX70 As you know, the capacity of the fuel tank of DAX is small to die
2.It's about 5L and that's it for a neighborhood leg, but it's a little farther out or suburban Service It's very difficult to go to a place with fewer stations..
I've had a spare Gasoline Carrying Can in the past, but this I've chosen Sub Tank!
The Hose from the Sub tank is connected to the Fuel Cock's RES and the MainTank's I reconnected Reserve to the Cook's Main Now I've used up the MainTank to Reserve, and then I'm going to use the Sub tank in this case If you switch, you can use Gasoline to its full potential
Mounting is done on the Left Side of the DAX bodywork Mounting is done by BoltQuantity:It's an easy 2pc installation
The capacity itself is about 1 liter, so it's really a spare W. It's dangerous to be overconfident It's okay, it's a Sub tank and it has a low capacity It's just cool to have it on!
Also, the tank cap does not have a Key
View detail
It's not strong enough
The bracket broke after 200km or so, even with the silencer band It's not strong enough and the bracket is not thick enough
I had no choice but to scrape off the original bracket and use Silencer bandQuantity:I use 2pc and make a Bracket on the body side
View detail
Not worth $9,600
Please note In my Initial ModelDAX, you need to remove the Helmet holder to be able to The only thing I can think of is that it's not a bad thing It is a large red letter with a return shipping cost of 960 yen though the description of the product is insufficient It's a good thing that the direction of the hose connection of the Fuel Cock is not in front of the carburetor You shouldn't do this, but it's facing backwards, so the hose will be 180°UTurn If you want to install it on the Left Side, please use No.0841 ($8,100) There is no Fuel Cock, but it is still better because the entrance to the Hose is facing forward However, I think that the Helmet holder cannot be installed if I see it in the movie When you buy it, please consider well View detail