Reviews
Diversion to GORILLA's Custom
Purchased for repair of GORILLA, same shape as OEM Product, made of plastic, but the plating is in good condition and the price is reasonable. View detail
Recommended!
Cospa!
Somewhat BALI….
Considering the price, I guess.
View detail
Cospar good
Cost-effective!
This is enough for processing!
It is a repeat purchase!
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Good Cost performance
The construction is very good, the 8inch seems to be spread out in the front and back, so I think the 10inch is probably the best fit. View detail
not bad, but ...
I think the cosmetics are better than OEM.
The plating is very clean at a glance, with no irregularities.
If you look closely, you can see vertical lines here and there that appear to be PRESS scratches? Vertical lines can be seen here and there during processing, which appear to be PRESS scratches.
I don't mind it much, but I guess those who care would be bothered by it.
There was no distortion or deformation, which is typical of Chinese Parts.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY
delivery product
Thanks again for fast delivery I dont have to say something bud for yours I wait for next buy from yours shop keep up the good work offered View detail
not bad
It is a Chinese part, but the plating is clean and can be used normally.
It also has a rubber cushion in the mounting hole.
View detail
Used for assembly from Frame
I was worried because it was cheap and it was made in China, but the quality was good and I was satisfied with the Large change! View detail
Used for assembly from Frame
I bought it as a trial because it was almost half the price of other companies' products, but I was satisfied because it was solid and the finish was good. View detail
One word:cheap.
Purchased for the purpose of diversion. The plating is beautiful and the edges are well treated. If I were to raise a bad point, it is heavy. The thickness of the steel plate makes it look strong. View detail
Used for 12VMONKEY
I put a Fender on temporarily for a change of pace.
I'm going to buy the OEM Plating fender because it looks like a good atmosphere.
Cheap and for reference.
The Bracket is self-made in position.
If you buy a slightly expensive OEM and it's weird, it's a Shock, lol.
View detail
It's tolerable..
I used DAYTONA 8 cm Long Swing Arm with a combination of 280 mm Rear shock.
Protection Seat is affixed to parts, Woundetc. There was not, BALI of the cut is amazing! Let's pay attention to injury.
There is no problem with the installation itself.
Although it may be attached as it is, in order to eliminate interference between Tire and Fender at the time of Stroke, we added a thin Washer instead of Color at the top of the Fender to earn a height.
Color not used sandwiched Plastic to attach Number under Tail lamp to retreat behind.
When the interference between Fender and Number is subtle, you can secure some clearance if you loosen the Carrier's installation Bolt once, raise the rear end gently and close it (^o^)
View detail
Fits: HONDA APE 50, HONDA NS-1, HONDA NSR80, HONDA APE 100, HONDA NSR50
If it converts to Wide!
In order to widen Front fork 's Top Bridge, Fender also needed Bracket for Wide purchase. The price is not high so it is recommended! View detail
Good looking but backwards for the ct70 cables. The chrome plating looks good with only a few little marks where it was put over the welds on the mounts. The mounts them selves allow for 2 different widths of forks. It just changes the height by 10mm o
Good looking but backwards for the ct70 cables. The chrome plating looks good with only a few little marks where it was put over the welds on the mounts. The mounts them selves allow for 2 different widths of forks. It just changes the height by 10mm or so. The only problem I have with them is that the cable holder is on the wrong side for my model. Maybe for a different front end it fits right. View detail
Clear the gap!
After attaching the Flatness Tire, the gap of the Fender became irritated due to the Large ruin, so we found out various products and arrived at this product. It's very convenient because you can set it to your favorite position.
Because it is a Stabilizer for the time being, I think that it also contributes to the rigidity of Front fork.
However, since the construction is sloppy and white stubs like Rust are attached in some places, people who care are Compound firmly and must polish.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
I love this fender. It fits my 8 inch tire (am not sure if it'll fit a 10 inch or not). It comes with no bolt holes drilled, so you can measure and cut your own. It's made of thick plastic with a durable coat of paint. I bumped it a couple of times and
I love this fender. It fits my 8 inch tire (am not sure if it'll fit a 10 inch or not). It comes with no bolt holes drilled, so you can measure and cut your own. It's made of thick plastic with a durable coat of paint. I bumped it a couple of times and it didn't scratch or chip. I would highly recommend this fender for a do-it-your-selfer, but it's definitely not for everyone. View detail
superb build. feels rigid and strong. very good chrome all around. fit is excellent, no troubles at all with all the cutouts exactly where they should be. highly recommended.
superb build. feels rigid and strong. very good chrome all around. fit is excellent, no troubles at all with all the cutouts exactly where they should be. highly recommended. View detail
being unexpected -- firmly made of being impolite if it says. The description was also attached (a photograph is unclear). Since the 5-cm LONG SWING ARM of the company was attached to the GORILLA, the position of the Rear fender was lowered behind. The
being unexpected -- firmly made of being impolite if it says. The description was also attached (a photograph is unclear). Since the 5-cm LONG SWING ARM of the company was attached to the GORILLA, the position of the Rear fender was lowered behind. The Balance of the result became very good. Since a Number plate interferes in a Rear fender, it bounds and is carrying out simultaneous wearing with the raising Stay. The Cap bolt is enclosed although an upper Stay and Frame are connected. But since the Fender became obstructive and a hezagonal wrench did not enter, it exchanged for the Bolt tightened from width with a Spanner. Only this is regrettable. View detail
Fits: HONDA APE100, HONDA APE50
It is unavoidable that compare that it is pure, and a wound enters also for attaching also for using a down fender at RIA since it is ? whether hard it will be divided if it bends forcibly? Since it was special plating, I wanted to attach finely.
It is unavoidable that compare that it is pure, and a wound enters also for attaching also for using a down fender at RIA since it is ? whether hard it will be divided if it bends forcibly? Since it was special plating, I wanted to attach finely. View detail