Reviews
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Product quality is the worst Level
After 5 months of ordering, it finally arrived and when I carefully unpacked it, it was covered in scratches. I am so disappointed. Don't they inspect the product before packing it.... It is a regrettable Manufacturer. I can't recommend them at all. View detail
For Racer9.
I bought this to install on my Racer 9GT.
I couldn't put it on because it didn't fit.
I think you probably have the wrong car model for the Racer9.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Large presence
Without much study, I decided to purchase Fender Eliminator, feeling that the higher the price, the better.
But now I don't like it because I see too many extra Frames.
My feeling is that Fender Eliminator must be Simple.
License Plate Light is also too Large and thick.
I can't change it to something different because it was too expensive.
View detail
Large modification is required and out of the question as a vehicle-specific kit.
OEM Blinker cannot be installed as is.
The only way is to process this product or Blinker into a Large size.
It is not a Level that doesn't fit a bit, so if you buy it, you should be aware of that.
Incidentally, Webig's conformity guarantee does not cover this degree of processing.
Below is the response I received when I inquired about the conformity guarantee.
------
For more information about the conformity of this product in our company, please contact us,
If the four holes of the product can be installed on the Rear side of the vehicle through the Bolt, the product is considered to be compatible.
Fixing the above to the vehicle. Conformity Assurance The following is a summary of the results of the survey.
View detail
Fits: YAMAHA Tracer 9, YAMAHA Tracer 9 GT, YAMAHA XSR900
XSR900 2022- Requires considerable modification for use
I bought it because it is compatible with XSR900 2022-.
The position of the mounting holes, etc., are considerably off.
RearThailandia is about to be contacted while driving.
So I gave up using it.
View detail
Depending on the individual, it is an expensive and inferior product!
The product was too shoddy for the high price and inconvenienced Shop who did the installation work.
The tip of the Hugger hit the tire and could not be installed without machining the bolt hole,
It is an amateur and very difficult task.
Depending on the individual, the product is terrible!
View detail
Couldn't order due to System inconvenience.
I couldn't order because the Security was locked or something!
Please don't introduce such System!
View detail
It does not fit TUONO 660.
I was looking for a Fender Eliminator for my TUONO 660 and ordered this parts because it has the same shape as the RS660. However, when I opened the box and temporarily assembled the parts, I found that the bracket was too long and hid the tail lamp. It would be impossible to install without cutting and drilling tools.
It would be good if we could confirm in advance whether installation is possible or not.
View detail
Fits: ROYAL ENFIELD Himalayan, ROYAL ENFIELD Scram 411
This is a dangerous PARTS and you should definitely not do it.
This is a fairly appropriate spec. that uses a single tie band to secure it to the swing arm. To detach the Swing Arm, it is necessary to remove the Rear Tire, insert the Swing Arm between the Rear Tire and the Swing Arm, and tighten it with a single Tie Band.
I was concerned immediately after installation, but after touring I realized that it was even more dangerous.
(1) First of all, the Fender tilts about one centimeter toward the Tire side due to driving wind pressure. (2) The clearance between the Fender and the Tire becomes narrower, and in the worst case, the Fender is rolled into the Tire, resulting in a large risk of breakage.
No matter how tight you tighten it, it is only a tie band. It cannot be fixed tightly.
I was not convinced that it was worth the price.
Once I installed it and damaged it, I couldn't return it and lost a huge amount of money.
I would never recommend this product.
View detail
Making is complicated
Pitch of mounting hole does not match.
The Pitch of the hole was additionally machined with Punch for drilling and installed.
Why are there such basic differences when it is supposed to be Exclusive Design?
View detail
It will crack.
I have made my first run after installation.
It is about 240 km on highways, mountain passes, and urban areas.
The wobble was large from the time of installation, and I was concerned about the strength of the product,
When I came home, I checked and found that Crack was there.
I am very disappointed because I like the position of the number, the texture of the carbon and the design.
If a lighter reflector is used without a license frame, it may be different, but a reflector made of gold would be a safe bet.
View detail
Miscellaneous.
I bought Side Panel because I liked it.
I did not check it as soon as it arrived and installed it just now.
Poof...
Something likeQuantity:Pair (for Left and Right) The holes are clearly visible after they were plugged one by one, and can be clearly seen in the right light.
View detail
Fits: HONDA CB1300 SBSP, HONDA CB1300 SF, HONDA CB1300 SB, HONDA CB1300 SFSP
Product
Too badly shaped, too expensive and too disappointing, Chain rubs on Chain Cover and is unusable, Rear tire is so badly shaped that it seems to roll in, View detail
Last year 44,000 yen ?? now 72,000 yen. I'm so disgusted by the vicious price hike.
The FRP fender was replaced by a Carbon fender from Kuh LaborWolf.
Easy to install. Just fit, unlike foreign products.
It's just...
The price was about 44,000 yen until last year, and now it has been raised to about 72,000 yen. Front has also raised its price, but Rear's price is worse. I think the price increase of less than 30,000 yen is quite malicious.
Moreover, it is uneven. (image) It is noticeable. The quality is not very good either. 72,000 yen for this quality and I regret buying it. I would like to return it, but it's non-returnable.
I don't think I'll buy KuLaborWolf anymore.
View detail
Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000, SUZUKI GSX-R1000
Not recommended!
As another person wrote, there is no terminal processing for LED Harness.
You must determine the polarity by yourself and connect at your own discretion.
*Manufacturer does not provide a warranty in case of polarity errors!
Of course, we're connecting them at the discretion of the operator.
Trouble due to Waterproof processing defects should also not be done by the Manufacturer!
The size of the LED-side Harness and Body-side Harness are different.
If the harness size of the terminal is the same on the LED side and the body side, I feel that there is no denying the possibility of crimp failure.
I have a 3M MINI ClampWireMountPlug 37103-3122-000 FL on the LED side.
MINI ClampWireMountSocket 7303-3163-000 FL is processed on the Body side.
Self Fuser Tape was wrapped around the surface to make it waterproof.
The MINI ClampWireMount can be installed with a pliers tool and is useful for changing the size of the harness between Male and Female.
I would like to request that if the product is sold as a kit, it should at least come with a terminal.
View detail
For those who can be creative and ingenious
I purchased this product to install on a 2022 GSX-S1000.
The design is great, but...
As I said, it is different from domestic parts.
First of all, this product cannot be installed by itself; for JapanNumber, three Bolts longer than the supplied Bolt by 5mm or more were required.
There is a bracket for installing an OEMBlinker, but it could not be installed without expanding the mounting holes with a file. This is probably due to the fact that the holes are slightly smaller and the paint on the bracket makes the holes smaller. It is not enough to re-drill the holes by Drilletc.
The wiring of the License light is also short and cannot be connected without an extension. The wiring is so thin that a Crimper for Thin Wire was necessary.
The product itself has only four O-rings for mounting on the vehicle body, and the blinker cannot use the vibration-absorbing rubber of the OEMB blinker, but is directly attached to the vehicle. This structure probably cannot withstand long-term use.
I wanted the License light to be lineup as Repair Parts.
Because of the shortcomings listed above, I thought it was for those who can be creative.
View detail
I bought it by mistake.
I made a purchase by mistake, it is like a pushy sale.
No response when I contacted them. Worst
Sorry, it's been about 2 months and this is my rating. Please contact me. I have filed for a return!
View detail
Is this a guarantee of conformity?
What is the conformity guarantee for this product?
Made by A-TECH yzf -r1 4xv Fender Eliminator cannot be installed, but I was prepared to have to do some modification, but there are some parts (distortion, etc.) that cannot be modified due to the specifications other than those shown in the photos.
View detail
Fits: BETA RR350 4T, BETA RR300 2T, BETA RR250 2T, BETA RR400 4T, BETA RR450 4T
Is it all like this?
Why is it so crooked when new?
Are you licking your chops?
Even if it's made in a foreign country, it's too much.
Wonder if all of WeBig's inventory is this crooked.
Do you not inspect the product?
View detail
That's $6,000 for this, which is crazy.
PeLePera too much hole enlargement Large necessary hassle! View detail