Reviews
Ligh Tech tail tidy
The quality of the components are excellent. Fit is also great, when you figure out how to do it! Zero instructions and resorted to YouTube tutorial from a different manufacturer. The hardest part was actually dismounting the OEM number plate holder. You need to cut the number plate light wire and reroute it. After that it was straight forward. View detail
Refreshing around the Rear
We chose this one because it was Reasonable price than other Fender Eliminator Kit.
First of all, when I first received the product, the holes in the Plate and Bracket did not match, and when I inquired about it, I was told that a different model had been included.
When I actually installed it, I had a hard time removing the OEMFender first.
There is no instruction manual, so I had to loosen the bolt and remove the parts, but there might have been some parts that I didn't have to remove.
The space under the Seat is narrow, so the Coupler for the lights is quite difficult to pull out.
Also, I used a small-sized MONKEY Wrench because the included nut was a size I don't usually use, but I think it would be more efficient to prepare a socket that fits the size.
As for the License Plate Light, I did not want to cut the OEM harness, so I purchased a Coupler that fits there separately and crimped the Bullet Terminal to extend the Cable, but the wiring of the attached License Plate Light is too thin. But the wiring of the attached License Plate Light is too thin, so be careful not to break the cable.
Colgate Tube was used for the wiring path and fixed to the Fender EliminatorBody with inHemp palmac.
The key cylinder of the Seat lock is screwed into the inside of the car body from the side. (I can't help but feel that the Seat lock release has become harder)
Speaking of the seat lock, the OEM dust-proof cover cannot be used, and the keyhole is exposed, so I think countermeasures are necessary.
I process thin rubber sheet and attach it with strong magic tape to make it removable and to prevent mud and dust from entering. (I've only run it a few times, but so far the keyhole is Large strong)
It took a lot of time to install the new product due to various modifications, etc., but it is a recommendation because it looks like a reflection.
(Although this will make the water splashing up behind the Fender a little worse.)
View detail
Be careful of misconnections
[How is it used?
Installed on a 2022 MT-09 SP.
The OEMFender didn't look good and even if it did, it would roll up mud and dirt, so I decided to replace it with a Fender Eliminator.
Was the one you received as per Image?
It looked better than it does in the image, but it takes Sense to hide Wiring nicely.
I don't have that much Sense so if you look closely, it's rough.
Was the installation difficult?
1.Needs to be completely assembled from RoseRose state.
2.The instruction manual is in English version.
3.Overtorque needs attention because of tightening by Bolt of plastic parts.
4.Wiring for License plate needs wiring processing
The four elements of the system make it a little difficult for a novice maintenance person to install.
How was your experience with it?
I thought it was worthwhile to have it installed because it looks Refreshing compared to the OEM parts. Also, the small parts have the Manufacturer's logo, which I personally think is GOOD.
[Included Parts:were they on?
Three instruction manuals and, although not used this time, a mounting bracket compatible with external blinkers are also included.
[Was there anything that disappointed you?
As is often the case with MT-09 external Fenders, when replacing the OEM Product, the key slot for removing the Seat is exposed and dirt gets under the Seat. This product still has the plate, so I think it is relatively better, but it would have been nice if the lid of the OEM Product could have been used in the same structure.
[Availability and clarity of the Instruction Manual
Note that, because this is an overseas manufacturer's product, it is different from JapanManufacturer's product and is not written very carefully. Also, the assembly method varies slightly depending on the shape of the license plate in each country, so it is necessary to assemble the product while confirming the shape of the license plate.
View detail
Better looking than expected.
First of all, it is light anyway.
I would say it is less than half that of OEMs.
Installation is also by pon. It's as easy as pie.
However, it is thinner than the OEM, or it rattled when attached as is.
I put in Spacer and it's ok for now.
I will try various Spacer Materials. Let's start with pon.
View detail
Installation is Large
No Manual etc., installation is tricky.
If the OEM bolt is used, it may crack with carbon, and flange bolt etc. must be purchased separately.
Also, the hole drilling is slightly misaligned, so it needs to be pushed in forcefully or some modification is required.
In my opinion, Magical racing”s Rear Fender Chain Guard integrated” would have been better.
And Rai TEC is about the same price to buy 3 Carbon parts around Rear except Rear Mudguard,
Magical racing Front Fender - I also had the manual when I purchased other parts. Above all, I have a sense of security in a domestic product.
View detail
Fits: TRIUMPH STREET TRIPLE 765 S, TRIUMPH STREET TRIPLE 765 R, TRIUMPH STREET TRIPLE 765 RS, TRIUMPH DAYTONA 675, TRIUMPH STREET TRIPLE 675 R, TRIUMPH DAYTONA 675 R, TRIUMPH STREET TRIPLE 675, TRIUMPH STREET TRIPLE S 660
Fender Eliminator with a little Mischief
Not only is this OEMFender lame and useless, but the License Plate Light is not LED. I built it so I could drive it on public roads." It is a product that is not well understood.
No matter how sunny the day is, if you try to drive on the wet surface of the Tunnel on the mountain pass Mudguards are for decoration! What in the world is OEM....
in that case If we're going to get mud on our backs anyway, let's make it a little shorter!" So we replaced it with this one.
The cheapest price, License Plate Light included, and the ability to use the OEMBlinker were deciding factors.
Reflector was not my favorite, so I went with Simple Design.
Of course, there is no helpful Instruction Manual like JapanManufacturer's, but only a few sheets of paper with very rucksack-like explanations.
Hurdle may be a bit high for beginners.
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB150R, HONDA CB300R, HONDA CB150R, HONDA CB300R
just right
As for the overall look, I am very happy with the way it turned out, almost exactly how I wanted it.
The areas I noticed during installation were
Instruction Manual is a translation (not please enter here, and the drawings are not large enough).
Nut size is 7mm or 13mm, which is not often used in Japanese cars.
Many screws and nuts are easily forgotten to be tightened.
License Plate Light requires Bullet Terminal installation
The screw holes were not always tight, and there were times when I had to adjust the screw holes a little.
I had a little trouble at times, but I was able to install the Large without any problems. I am satisfied with Large because it looks more to my liking than anything else.
I am wondering if I should change the blinker since the blinker bracket also comes with an external smallest blinker.
View detail
Fits: BMW S1000R, BMW S1000RR, BMW S1000R, BMW M1000RR, BMW M1000R
Wow that's cool
I am satisfied with the design, which is more Refreshing than OEM.
If I had to say one thing, it would be that I am concerned about the durability of some of the resin parts.
View detail
Fits: APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 FACTORY
Fender Eliminator that is not too short
For installation, the license lamp requires Wiring, and the OEMConnector was diverted.
Since Blinker is an Other Brand Product, Puch's BlinkerCable was purchased separately.
It looks a little long, but it is natural if you look at it as a whole, and I chose it to prevent mud splashes and to install a side bag, so this looks just right.
View detail
For those who can be creative and ingenious
I purchased this product to install on a 2022 GSX-S1000.
The design is great, but...
As I said, it is different from domestic parts.
First of all, this product cannot be installed by itself; for JapanNumber, three Bolts longer than the supplied Bolt by 5mm or more were required.
There is a bracket for installing an OEMBlinker, but it could not be installed without expanding the mounting holes with a file. This is probably due to the fact that the holes are slightly smaller and the paint on the bracket makes the holes smaller. It is not enough to re-drill the holes by Drilletc.
The wiring of the License light is also short and cannot be connected without an extension. The wiring is so thin that a Crimper for Thin Wire was necessary.
The product itself has only four O-rings for mounting on the vehicle body, and the blinker cannot use the vibration-absorbing rubber of the OEMB blinker, but is directly attached to the vehicle. This structure probably cannot withstand long-term use.
I wanted the License light to be lineup as Repair Parts.
Because of the shortcomings listed above, I thought it was for those who can be creative.
View detail
Good vibes
At any rate, I bought it because I wanted it to be a Fender Eliminator.
No problems except that the Screw that came with it was broken…
View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10RR
sitting on the floor grasping one's knees (as in a gym class)
Was the one you received as per Image?
The shape was exactly what I expected and the location and Size were Exactly more than I expected. I thought there would be a little more laxity in some areas.
The weight was much lighter than expected.
Was the installation difficult?
Easy.
How was your experience with it?
The installation position is more rearward than other products. It may be different for different tastes.
The angle of the License Plate is variable, but the angles of the License Plate Light and Reflective Plate are also variable.
Well, I'm glad to hear that your butt is looking good.
[Included Parts:were they on?
It is very tight with no leaks. I have an extra Bracket from Rai TECfor Blinker, but I would like to buy Blinker when I feel like it.
[Was there anything that disappointed you?
I wish the Wiring of License Plate Light was a little longer.
[With or without Instruction Manual
I can't read Italian.
[Notes]
One of the couplers (White) of the OEM License Lamp will remain on the OEMFender side, so some modification is required for wiring.
I cut and brought the OEMFender side and processed the WiringBullet Terminal because it was troublesome.
Blinker does not require processing because OEM is attached to Beauty.
The fixing part on the nut side of the reflective plate is plastic, so care must be taken when tightening it.
Point and hang of installation
The Lai TECLicense Plate Light has a License Plate Light (White line) and a Stop-lamp (Red line).
OEM side Stop-lamp (Blue wire) Tail lamp (Red wire).
There is plenty of room here, so the Wiring Connector is the quickest way to get into Wiring.
Wiring together in the back is a Daiso product (see photo).
View detail
2021- MT09 with pons!
We have a lot of stuff at LighTech, but Material and Fitting are also well Recommendation.
LighTechFender Eliminator is also a good idea, since it can use the OEM Blinker as is!
View detail
Fits: APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 FACTORY
Aprilia RS660Fender Eliminator
The product is a matte black color and is of excellent quality.
The product details stated that the License Plate is also compatible with the Japanese standard Plate, so I decided to install a Rai TEC License Plate with Reflector on the RS660. (Complete) selected.
View detail
Fits: APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 FACTORY
Aprilia RS660 Fender Eliminator
The Ry TEC products seem well-made.
It was just that the Fender part was a little shorter than I had expected.
I thought it would have been a little more stylish if it was just below the Tail lamp. 。 I am satisfied with the product because the Fender is shorter than before.
Is it difficult for a beginner to install a license lamp?
There is also the task of taking Earth to MotorcycleBody, which requires knowledge.
The Blinker will also be exposed to the Wiring, so you will need to prepare parts to cover it! I installed a homemade machining box on the Rai TEC product so that the Wiring is not visible. (Waterproof processing and external protection to prevent water and mud from getting on Wiring even in the rain)
If you can tinker with Motorcycle to some extent or have wiring knowledge, Large is sturdy.
I also skipped the Fuse in the Tail section once.
The Instruction Manual is of course the English version.
View detail
Lack of product description.
Even if you buy only this product, you can not install it to the car body.
You will need to purchase the Screw or broken Pin elsewhere.
View detail
of poor quality
In a word, it's a shoddy product.
The screw holes that are opened are gapped, so it can not even be installed on the car body.
I couldn't sell inferior products on Yahoo! Japan, and as a result, I had to pay tens of thousands to buy Garbage.
If you were considering buying one besides me, be warned.
View detail
Fits: BMW S1000RR, BMW S1000R, BMW M1000R
Fitting is perfect.
It is a little longer than NORMAL.
The Bracket part of the Chain Cover is more solid than other manufacturers'. 。
I think the product is perfect.
View detail
Fits: KAWASAKI NINJA 250, KAWASAKI NINJA 400, KAWASAKI Z400
Great product
The Fender Eliminator is great for achieving a tidy and short tail. The product is well made and fit for the bike. The only problem is that it it a little bit long for the licence plate of Hong Kong. Otherwise it is perfect. Recommend to anyone who want a clean shape of bike. View detail
Good enough for Suspension mudguards.
When I go through a puddle of water, even a little bit, the Rear Suspension gets dirty, so I was looking for a good fender and came across this one.
Installation was easy and SMART without having to remove the wheels as long as you have a long driver.
I think it is functionally effective as a suspension mudguard, but…Well, it is not very large, so if you run in the rain, your back will probably be sloppy. (Lol)
Instead, the Design is Refreshing, and I like it.
View detail