Reviews
Genuine Pyramid Plastics Enduro Fender for 2020 MT07
A customer wanted to get an extender for their MT07 to help stop water flick from the front wheel. Having not used one of these before on any bike, I asked the customer what they preferred. They chose this one from Pyramid Plastic. Good choice from doing my own research. The fender extender was not hard to find once you put your bike details in the website and the options appear. The extender was not overly expensive and added to a few other small parts in my order, I had them all shipped via EMS. I do have more than one item per order as this does cut back on the shipping cost somewhat. The order arrived in 5 days from being shipped and was well packaged and in 100% perfect condition. The fender extender came in the Pyramid Plastic sealed packet and was wrapped in bubble wrap from Webike warehouse to keep it safe. You do have the option of using the stick pads for this fitment or better yet, just drill the fender and attach for a more secure fit. This was the route we went. The extender is made of and ABS plastic as far as I can tell and the fitment of this is absolutely spot on. The quality of the part is excellent. A nice matte finsih which does go very well with the bike anyway too. I did think there may be a slight gap once test fitting but there was no gap at all. Took a little over an hour to do the job right but the result is really good. View detail
Great extender
A great extender for the front fender, very nice fitment and easy installation. I choose the stick on type with the stickers provided. View detail
Need to be a little creative with Screwdome.
I bought it because there were few other options and I thought it would be better to buy it than to use it by trial and error and have more unnecessary parts.
The bracket for the Right Side is included, but when installed as per the screw holes, the pressure applied to the Fender feels unreasonable, so the existing holes in the bracket need to be widened with a drill or newly drilled to shift the fixing position with the Swing Arm.
Since the two holes on the Fender side do not match at the same time, only one hole was used and the unused hole was filled with black SiliconPate. However, it only takes 20 minutes to adjust the holes on the mounting bracket.
Item number as for FZS600 07214." When 07227. but if it is FZ400 compatible, 5DM series (Fazer 600 1998-2001) of 07214." becomes. 07227. is a 5RT system.
View detail
Depending on the individual, it is an expensive and inferior product!
The product was too shoddy for the high price and inconvenienced Shop who did the installation work.
The tip of the Hugger hit the tire and could not be installed without machining the bolt hole,
It is an amateur and very difficult task.
Depending on the individual, the product is terrible!
View detail
PyramidPlastic Red R258 Rear Fender
[Usage]
・Touring
Image Street?
I bought it because I thought it would go well with the OEM color Red RC211VPLOTTypeMotif color.
Finished as per Image.
Is it difficult to install?
Easy
ExactScrew hole fits, not possible, but no machining was required.
How was your experience with it?
I'm satisfied with the results as shown in the Image.
[Included Parts:were they on?
With Mounting Screws and Instruction Manual are only available in English with no illustrations.
[Was there anything that disappointed you?
Nothing in particular.
Rear The part of the suspension that prevents dirt from splashing onto the suspension is not perfect, but it is only slightly less prone to dirt.
View detail
A must-have for any Fender Eliminator
I was worried about mud splatter if I went with the Fender Eliminator!
I've been waiting about 3 months for this too due to world conditions lol.
I'm happy with the design, it's Carbon all the way!
The overall effect is to prevent mud splashes, so it is virtually dirt-free.
There may be some on the TapeLamp area, but I wouldn't worry about it!
I was told that the Tire looks thicker and Parenthesis looks better from the following Motorcycle, so I'm very happy!
View detail
It works quite well.
Gold molds are not well made, or maybe it's because of Quantity:Pair (for Left and Right) is an unbalanced product, which I don't think is possible from Japan's point of view, but once it is installed, it is a Quantity:Pair (for Left and Right) The balance of the front wheels is not broken. The effect of preventing mud and water splashes from the front wheels is unexpectedly good, and the effect is very large. It is easy to install, and I am glad that I installed it. View detail
Compared to the cheaper one
P&AInternationalExtender I read the impressions of Fender and found the roughness of the molding to be noticeable and cheap, so I was prepared to be a human pillar and bought this one, which did not have any reviews.
The estimated shipping time for the WeBig was three weeks, but it took EXACTLY three weeks to arrive.
The contents included a FenderBody, a plastic Clip for drilling and fastening, and a Strong Double-sided Tape.
I didn't have the courage to drill holes in the Fender, so I fastened it with double-sided tape only.
The molding, which is of concern, is distorted as expected.
Quantity:Pair (for Left and Right) The upper part of both theQuantity:Pair (for Left and Right) It is not symmetrical.
It is not noticeable once installed, but it may bother some people.
Installation is also quite troublesome since the Front Fender has to be removed.
However, the head cover of the engine's cylinder was also dirty from the mud splashing on it, so we decided to put it on.
I haven't tried the effect yet, but I would like to check it then, as I will be stepping on puddles and gushing water if I drive on mountain roads sooner or later.
View detail
Poor adhesion? Lost while driving
Design and quality are fine, but was the adhesion bad? It flew off and was lost while driving.
Second ・・・・. I still may need a separate double-sided tape.
View detail
Just fit.
I bought this for the purpose of protecting the Engine area from Small stone bounces and Mudguard.
The installation etc. was as described in other people's impressions, and was secured with strong double-sided tape and plastic screws×4.
I was a beginner at drilling holes for Screw fasteners, but I managed to do my best.
After installation, it feels really natural and truly just fits, just as it did from the beginning.
View detail
You get what you pay for
cheapest mudguard It is recommended to install with screws Don't use double-sided stickers, it will make you regret More mudguard length would be better View detail
Fits: HONDA CB 1100 RS, HONDA CB 1100 EX, HONDA CB 1100
Easy to clean, used on CB1100EX
Used for CB1100EX.
This is a model that has already been discontinued, and since it hasn't been popular in the past few years, there are very few parts available, so I bought this one.
The purpose was to fix the mud splashing on the exhaust pipe and engine area.
Even after cleaning up the exhaust pipe and engine, the length of the OEM front fender was getting dirty quickly.
After installation, the area that gets dirty became smaller, so cleaning became easier. Most of the dirt is concentrated in the lower part of the Engine.
I installed it with the supplied seal and screw. I did not install the screw because it requires drilling.
I did not have to worry about it coming off. However, I haven't driven 100km/h, so I'm not sure what will happen if I drive on the highway.
Of course, I cleaned and degreased it thoroughly before installation.
View detail
Recommended for Fender Eliminator vehicles.
I was able to install it on KATANA.
This is a recommendation for those who are using Fender Eliminator.
View detail
subtle
It's hard to put on, it's easy to get scratched on various places, the difference between domestic and foreign products is huge, and it's expensive. View detail
Natural.
The front fender of the SV650 is short, and every time I went touring, the Radiator was hit by small stones and dirt from the water splashing on the road. I installed this product and I think the effect is large.
As for the attachment, it seems to be attached with strong Double-sided Tape. However, because I was a little worried if it was only that, I drilled a hole and fastened it with Screw of the attachment.
It looks so natural. It was there from the start. It's like that, so it's Recommendation.
View detail
Fits: YAMAHA Fazer 600 2002-2003
Understated OEM style design
[How is it used?
I'm using it for street riding and touring.
Was the one you received as per Image?
I wanted something with an understated OEM style design and Image was right on the money.
Material is black gel coat material which is standard for this kind of handmade products.:FRP。
The whole thing was carefully finished and there was no rough surface or section.
Was the installation difficult?
I had some trouble to remove the OEM chain cover and to pass the front mudguard of the Fender between the Tire and Swing Arm.
How was your experience with it?
I imagined that if I remove the OEM mudguard right behind the rear suspension, the air flow behind the engine would be rectified and the cooling efficiency would be improved. I imagined that removing the OEM mudguards would improve the cooling efficiency, but I haven't removed the OEM mudguards yet because I don't think it would make much sense since the engine is not very thermally sensitive. (Lol)
[Included Parts:were they on?
3 screws and 1 oval plate for fixing Fender. 3 screws and 1 oval plate for fixing Fender.
[Was there anything that disappointed you?
If I had to say, it would have been better if the Chain Cover part was 2cm to 3cm longer in the front direction.
Other items that would be helpful
Instruction Manual was included, but of course, it was English version, and moreover, it was roughly large. (Lol)
It is not difficult to install because it has few parts.
Since there are only 3 fixing points, it may be safer to use a low strength screw lock.
The delivery time was about a month and a half, which is reasonable since it was ordered from Europe.
View detail
Simple & Practical but Pricey
It is a simple installation, would not take more than 15 minutes to install. Light ABS material and given strong adhesive double-sided tape is all it needed. Having a mud-guard is practical in helping to guard the beautiful chrome exhaust extractor/radiator from pebbles, mud and sand. Haven't driven in heavy rain yet, hopefully it will hold up. The only drawback is the price. View detail
Fender Eliminator + SprayGuard.
Removed Fender with the presence of KATANA
Lightweight with SprayGuard
The Rear area has been Refreshing.
View detail
Lightweight with SprayGuard
Was the one you received as per Image?
As per Image… The downside is that it's expensive.
View detail
Lightweight with SprayGuard
Was the one you received as per Image?
Lighter than I imagined …Large satisfied
View detail