Reviews
Fits: KAWASAKI ZX-4R, KAWASAKI ZX-4RR, KAWASAKI ZX-25R
Small modification required
I wanted to improve the grip at a track meet, but not enough to install a race cowl, so I decided on this product.
Weight is approximately 950g, a slight increase in weight from OEM (FRP).
Color because it will get dirty with Rubber replacement.:It is unpainted, but the matte texture makes it feel comfortable as it is.
The installation of the product was partially interfered with by the body of the car. The installation itself could have been done without modification, but we did not want the stress to be concentrated and cause cracking.
Fitting is otherwise good, and the rear end, which had a wide gap in the company's 10R model and seemed prone to water and dust infiltration, is now better aligned.
The attached rubber was already cut, but I beveled it with File because the Edge was going to be damaged.
The installation was a few Bolts, but it was unexpectedly time-consuming due to its location in a narrow space, and I was thinking of switching to NORMAL depending on my mood, but it was such a hassle that I didn't feel like doing so.
Wet type rubber is attached. The gripping feeling is very large, but it is difficult to shift a little while sitting on it because it grips as if it is attached.
The sponge also feels resilient to the touch, but when you sit on it, it feels chica-chic and is not suitable for everyday use.
(It's RaceParts, of course, but I was thinking of using them on a regular basis because they are a pain to replace)
View detail
Fits: KAWASAKI ZX-4R, KAWASAKI ZX-4RR, KAWASAKI ZX-25R
Great sport seating position, good for city as well!
I am 175cm tall, and after installing the seat, I am able to stand on the balls of both my feet. WIth the original seat, I am able to place both feet flat on the ground. The raised seat makes me lean forward slightly more, reminding me to grip the tank with my legs rather than leaning on my wrists. Seating position is more sporty compared to OEM seat, i.e. sitting on top of the bike rather than inside the bike. Comfort is perfectly fine for street. If it is too harsh, perhaps you can adjust the compression and rebound settings on rear shock. Installation is easy - you will have to partially remove the side fairings to access some screws. It is NOT a drop-in replacement. Access to battery and fuses will be inconvenient after installing as you will need to remove fairing, screws and seat mount, before accessing battery and fuses. (It should not matter much but good to know information). Be careful not to strip the OEM bolts near the tank, they are very soft. Deduct one point as rubber seat provided has holes that are not very accurately cut, impacting the positioning somewhat. You might be luckier than me. Product shipped about 1 week earlier than estimated. Overall very satisfied. View detail
more than expected
Compared to replacing a Single Seat, it is inexpensive, and it is a good cosmetic product with direct information from Motorcycle. View detail
Fits: YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3
Wet Type with excellent gripping power!
[How is it used?
Tail cowl and seat base are of course made by Saiya.
I think this is basically FOR Repair. I thought it was an Upgrading item.
When you buy a Tail cowl, you think it comes with Standard, but when you buy a Tail cowl, it comes with Quantity.:Seat rubber is also set.
It was High PERFORMANCE.
Was the one you received as per Image?
It was just like the Image! I wanted this Wet Type!
Previously, only the dry type was available in the lineup, and the dry type was not durable.
I disliked it because it would fall to pieces and lose its Grip power when it started to fall apart because it was defeated by my buttocks.
So, until I learned about this product, I had been using Magical racing's Wet TypeUniversalSize
It was cut out and used.
Was the installation difficult?
It is cut beautifully in the shape of the Seat Base, so there is nothing difficult about it.
The best place to put it is on the floor, so we carefully degrease the surface before applying it, and also try to find the best place to put it by actually sitting on it.
If you Masking and apply it carefully, you will not make a mistake.
Since the adhesive surface is strong, it is not possible to reapply the adhesive once it is attached.
How was your experience with it?
It's great. Grips well and lets me concentrate on Riding!
[Included Parts:were they on?
None. This product only.
[Was there anything that disappointed you?
Not on the product itself! If I may say so, it would be even better if the Cut was a little more Large and the Rider could be adjusted as desired.
View detail
To prevent Cowl Burn
Under Cowl's Exhaust SystemI bought this to prevent burning from heat.
As I was in a hurry to put it on, I didn't do any degreasing and just flopped it on, but surprisingly, the adhesive strength is quite good and it still hasn't come off.
Since it is not too thick, it can be attached without worrying about interference from exhaust pipes.
Under Cowl alone is definitely too much, so you may want to stick it on the bottom of the tank, for example, or wherever there is a Merit when insulated.
View detail
Increased Ass Grip Power
Race seat&Base that can be installed on the '15 and later model R1.
Myself I chose Seat Height 15mm UpType, but usually Recommendation Type without change
The Large is superior to the Osset Grip power, and it is excellent to realize the effect very much in Circuit driving.
However, if you are going to buy it for other dress-up purposes, you can never recommend it.
The seat of the R1 is so hard that it is almost as hard as a piece of plastic, so it is impossible to sit and drive properly without a leather suit.
My only complaint is that the price is too expensive and the included Bolt is not a Hex Type.
I'm also a little concerned about the unnatural gap created in front of Seat
However, it is completely Circuit Use Only, and if you don't want to change the set to Race cowl, this product will be the only choice!
View detail
It's not a good editorial
Installation Instruction Manual written with Single Seat installation It is very confusing
The "Included Parts:" section is also written in one place, so it's all there until you try it on You can see if it's happening
(used to make a request or demand) won't work
The screw hole to attach the seat base to the body is not open, so you need to open it by yourself existence (at present)
I'm not sure if I forgot to open it I think I forgot to open it because it's not mentioned in the Construction Manual
The system of products is based on Quantity:Pair (for Left and Right) It's asymmetrical or doesn't have any holes in it, which isn't very good
。
The shape of the seat rubber is very different from the product in the photo
I'm glad to see that it seems to be able to be installed without any problems when I tentatively assembled it
Included Parts:Seat Base, 6 screws seems to be enough
View detail
Parenthesis OK!
OEM Seat Cowl changed so it changed. It became difficult to use Accessory Case etc., but there are no problems in other respects. Parenthesis better than anything! View detail
White blur has come in..
Clear paint has deteriorated White by about 2 months after it is attached to the car body.
I want to be honest returned goods!
In the future this manufacturer will never buy again.
View detail