Reviews
POSH Aluminum Pillion Belt Cover
About quality and texture Well made aluminum from POSH. The cover gives a beautiful outlook compared to the stock sliver look. About the feeling of use It's a cover that fit perfectly without any lapse in space. Difficulty of installation Less than 15 mins to remove the original screw and place the cover on with the given screws. I hand tighten the the screws as hard as possible. Cost performance and comparison with other products There's no comparison with others as there isn't any similar product around. The price is not expensive but it gives an additional look in your plain looking seat. About shipping and packaging Shipping is not expensive as the the items are small. Items are place in a vinyl plastic bag but no visible damage after shipping. Any concerns, cautions, or advice when purchasing The given screws length is long enough as there's worries about the safety of the belt if the pillon is to grab it. Make sure it's well tightened and theses should not be a problem. View detail
Fits: SUZUKI SV650 N, SUZUKI DL 650 XT V-Strom, SUZUKI DL 650 V-Strom
The CP is also good.
From the name PyramidPlastic, I was prepared to order some more cheap products.
In fact, the FRPParts arrived with a high degree of precision, which is quite high for exterior Parts from overseas.
The bracket engages the Crankcase Bolt firmly, and the engagement with the FRP part is not bad.
However, the supplied Bolt is a bit short, so you may want to prepare a Bolt of about +5mm.
It is not impossible to stick to FRP, but it does not put a load on FRP, and above all, it increases work efficiency by a large margin.
In fact, a separately purchased DesignBolt was used for installation.
I have the impression that it took quite a long time, but it is because it is an overseas parts.
Considering that the FRP parts are solid and cost only 20,000 yen, the cost performance is also good.
View detail
Grip is good
Grip is good and can be held properly.
Double-sided tape does not have a bad bite, but the resin part tends to peel off easily due to temperature changes, etc., even if the tape is degreased properly.:When applying to Unpainted resin, it is better to use strong Double-sided Tape for Vehicleetc.
The Cut surface is standing up and may catch on the seams of the Pants. I used Cutter to cut off the corners.
View detail
Simple is good.
Installation is very easy as it is fixed with a tie band, but I am concerned that it may move in the future as the tightness is weak.
I installed it on my OHLINS front fork and I like the simplicity of it.
There are other, more expensive ones out there, but I think this one will suffice.
View detail
Cost-effective, but requires processing
There is a process to make it like a plastic model.
The letters are attached one by one in Rose, so after folding the nails and taking out the BALI, they are framed in. This process was very enjoyable and had a Petit Custom feel to it.
When installing, the underside of the body interferes with the Fork Cramp, so modification is required.
I shaved more than 5mm at Grinder. (See photo)
Front looks better and I am happy with the low price and enjoyment of PetitCustom.
View detail
Fits: YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ250F, YAMAHA YZ450FX
I purchased this product because I plan to replace the exterior.
I can't say for sure since I haven't received the exterior yet, but it looks solid, thick, and sturdy.
It seems to need some hang to paste, but I guess it's not a problem since forest roads and Enduro are Main.
View detail
Fits: YAMAHA YZ250, YAMAHA YZ125, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ250FX
Not yet installed...
It is thick and firm. I wonder if it needs some hang to stick. View detail
Fits: SUZUKI GSX750 KATANA, SUZUKI GSX1100S KATANA (KATANA)
Cool ?
The cosmetics are very good and look very nice. View detail
Many SR riders use it! (p∀p) aha!
[How is it used?
I wanted to put something Iconic on my car, so I decided to use it.
Was the one you received as per Image?
I believe I received the exact image of the product.
The inside of the lid has a tight Rubber so I thought the waterproof property was also good.
Was the installation difficult?
I think it depends on the installation location, but it was not difficult because I just crimped it into the available hole.
More than that - I was worried about the Logo to put inside, mainly because of the angle!
How was your experience with it?
Once attached, it does not bother me. The place where it is attached is not visible when riding, and it is completely self-satisfying.
[Included Parts:were they on?
No, it would be better not to add "Included Parts:" to increase the price.
[Was there anything that disappointed you?
None 。
It is a good Manufacturer that also offers Logo that fits the size.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Before purchasing or installing the product, it is recommended to test the product on a piece of paper, etc., against the part of the car body where you plan to install it to see how it will look, so that you will not make any mistakes.
View detail
Newly confirmed as compatible with KF54 (ADV160)!
To JK05.KF47 It works somehow." It was a confirmation of the fit of the However, it was a just fit for ADV160 (KF54). View detail
Fits: Others Universal
I wanted something inconspicuous.
Reflector is now required for installation of KOSORear Mudguard KS-MGXF-01.
We chose this product because it is not assertive and prevents the License Plate from bending.
Reflector was replaced with KIJIMA Reflector Slim 3, part number 305-2146.
KIJIMA Reflector Slim 3 can be installed without modification, and both the reflector included with the product and KIJIMA products are secured with M5 Hexagon Nut.
We believe that measures to prevent loosening of the Nut are necessary.
There are several ways to prevent nut loosening, but in my case, I use Nylon nut (something like Self Locking Nut) I used the
View detail
Looks great!
When riding in the rear seat, I felt that the Belt alone would not support my body, and I also wanted to customize the look.
I haven't actually put a person in the Rear seat, so I don't know for sure how stiff it is or how it feels, but when I leaned on it myself, I thought it was sufficient for my needs, so I'm giving it one star.
Design and appearance are still cool.
View detail
Highly effective in preventing mud splashes
There was an 85mm gap between the OEM Mud Guard and the inner fender, and there was a lot of mud splashing from that area.
The License Plate and Top case get dirty when driving in the rain, and I was looking for something better and found this product.
This is a dedicated product, so it can be installed without any modification.
If you are not concerned about the torque, you can install it with only a 4mm and 5mm Hexagonal Wrench, and the work time is about 10 minutes.
In the photo, the hexagonal hole has a plug, but the plug is not included.
Surface is Carbon Style PP (Polypropylene) Made of.
The OEM Mud Guard has a reflector, but this one does not, so you will need a separate license frame with reflector or a reflector that can be tightened together with the license plate.
View detail
StylingUp and Improved usability
Styling couldn't be better.
However, the difference is Large because the OEMSeat is too comfortable, but the Cornering by the appearance and the load from the buttocks is much improved.
View detail
Fits: GASGAS EC250, GASGAS EC300, GASGAS EC250F, GASGAS EC350F
Installed on MY2023 EC250
I bought this for my GasGas EC250 MY2023 which I always use for forest road touring.
Since it is used for slightly intense forest road touring, the exterior is quickly falling apart.
I always buy the Exterior Kit from Poly sports because I can buy the whole set at a very reasonable price.
The quality is no different from OEM products, and there is no tendency to crack, which is common with Chinese plastic parts, making it very useful.
View detail
It needs to be shifted a little and put on the 2024 CBR600RR.
2024 CBR600RR compatible products (?) but it hits in the search results as
The shape of the knee side is slightly different, so it needs to be shifted and applied.
The glue was coming off a little bit, but other than that, I'm satisfied!
View detail
ease of use
Very easy to handle. View detail
Windproof effect + does not destroy Style + makes cleaning easier
I have an OEMHigh Windscreen, but when I replaced the Helmet, the Wind Cutting noise became worse.
The wind was now coming from the upper half of the helmet, but if the Adjuster is raised to the Largeest setting, the wind is no longer coming from the helmet at all.
It is easy to install, and if the adjuster is lowered, it hardly disturbs the style.
It was also good to have space between the Screen and Bracket, making it easier to clean.
The disadvantage is that it is not possible to put something like a Screen Mounting Bar Holder between the Screen and Bracket due to the installation, and the price...
View detail
Nice touch - but problems for yourself
Installation is a nightmare. You have to remove your whole tail assembly except you subframe. The new undertray comes with battery slot, but misses some of the grooves required to route wire harness. Putting back the tank had challenges. Fitment is ok. View detail
It's fine without it, but it's not tight enough without it.
[How is it used?
Mounted on Archi's Seat
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Not difficult, but since the length is Limit, Bolt tightening while pulling a little.
How was your experience with it?
Without it, Seat's Balance looks bad.
[Included Parts:were they on?
Mounting Bolt only
[Was there anything that disappointed you?
Nothing in particular, but I wish it had been included instead of sold separately.
View detail