Reviews
It can be installed on the '24 model, but I'm not sure if the effect is worth the price...
I wanted to improve the footing of my ZX-6R, which has a Seat height of 830mm, and I compared the images with those of the 23-year-old model when I switched to the 24-year-old model, and decided that they were the same. I was lucky if I could feel the effect of 10mm bean jam removal.
I'm not sure if I'm comparing the OEMSeat correctly since I've only used it for about 30km, but I didn't feel much of an ankle-less effect or improved seating comfort with the low rebound material incorporated.
However, the fact that the Lines are more curved with corners than OEMSeat makes it easier to transfer the feet.
To be honest, I think the effect on the investment amount may be disappointing, but it may be good to have for those who are clutching at straws to improve their footing!
View detail
The colors, ...
Attached to the helmet along with the MORIWAKI muffler.
As you can see from the sixth introductory photo, the color is lighter.
So I put it on a Graphic-colored Helmet and the Graphic became transparent. (Photo:above)
If you are concerned about it, layer it with a single-color Base. (Photo:Bottom)
Good thing it came in a two-pack.
PS:A minor point:the cutline on the outer edge is partially gapped with the text.
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25
Not an exact match.
The texture is good
I think the adhesion is also firm.
View detail
I prefer a little more Up.
I wanted a little more angle on the Up. It would be better if the angle could be adjusted. So I am not satisfied with the angle of this Number.
Installation is not difficult, although a little cumbersome.
I wish it were a little cheaper.
View detail
Koo~ Oshii ?? (?"-??? -?) ?".
I used to get frustrated when I couldn't remove the CALI Sticker from my Number because I couldn't remove it to Beauty, but thanks to you, I'm going to be free from frustration ^^.
I think it is a good purchase because it can also serve as one point of dress-up.
…… is,
When I installed it, it was too close to the NumberLeft hiragana, so it took about a quarter of the time as it was.
The hole was enlarged horizontally in Drill and shifted to the Limit to finally achieve the current shape (see image).
I can't say for sure, because the form of Number varies from region to region, but at least in my area Number requires processing ^^;.
I also thought it would have been better if the four corners were slightly rounded.
View detail
Stainless black
We replaced it with Stainless Steel for rust resistance and Black for good looks.
The product is good, but the price is a little high. I would appreciate it if it were cheaper.
We would like to replace the bolt as well, but there is no size available, so only the lock nut was replaced this time.
View detail
Blinker overhang is a bit weak.
The degree of difficulty in assembly and installation is low, and as is typical of DAYTONA, the precision of the product is high.
Were there any changes due to the year in which some parts differed from the Instruction Manual?
The balance between law and design is good, but I feel that the design could be a little more aggressive.
What I'm interested in is Blinker's Quantity:Pair (for Left and Right) Amount of overhang.
When the company's License Plate Base is installed, the Blinker becomes quite difficult to see.
At the time of inspection, the Number must be shifted slightly or it may not pass inspection.
View detail
Quality is good, but accuracy is subtle.
The quality of the carbon itself is fine, but the accuracy of both SIDES is not so good. The tank cover itself is difficult to install, because it is made in the shape of the tank cover, and the gap is inevitably caused by the thickness of the double-sided tape. Well, I think every manufacturer has this kind of accuracy.
Tolerable.
View detail
V-max 1700 under cowl(Twill Carbon)
I ordered it on June 25th... I received a reply that the expected delivery date was October, but I received it approximately 5 months later. Unfortunately, the customs clearance process was complicated, resulting in additional costs and additional freight charges. View detail
Price per piece
I think it would be good for a small accent.
However, if you say it is self-indulgent, it is sold in one.
Quantity:I bought it because I thought it was a good price for 1 set of 2pcs.
Quantity:Pair (for Left and Right) If you would like to have a Quantity:2pc. Set need to be bought.
I didn't see that mentioned in the WeBig, so ….
I had no choice but to buy another one when it arrived and I only had one.
It's a two-step process.
It seemed a bit expensive.
The product itself is good.
View detail
Increases the sense of Hold.
Compared to OEM, the tank shape is raised so that the body can be held without moving too far forward when breaking.
The use of a tank pad will further reduce slippage and increase the hold feeling. It is especially recommended for those who run Circuit with GunGun.
View detail
Replace SR with WM's Semi Double Seat IV.
This is a replacement from DAYTONACOZYSeat, but the Seat height will be slightly lower.
The raised Rear makes it easy to check the Fitting position on the buttocks.
The seat feels soft and quite thin, so it seems hard to sit for a long time.
The space between the Seat and Tank (about 2 cm) is slightly empty, so if this bothers you, you may not want to do this.
We are bulking up with TankOffsetParts from Bore Ace, so the gap is about 1cm.
The bi-Ping gives a slightly softer impression, which may be to the liking of different people.
I had no problems at all with the Fitting of the installation.
View detail
First Rear CarrierBOX
Unlike the Scooter, there is no storage space, which is also the fate of a naked motorcycle. I looked around to find a better looking frame for the carrier, and chose ENDURANCE because it seemed to have the most strength.
SHAD (Shad) I use it in combination with SH40. Based on the other's Impression, I judged by myself where Screws and Nuts are likely to loosen and put in 6mm Spring washers. I have not yet installed it on my car, but I am looking forward to seeing how durable it is.
Also the Instruction Manual for handling, but it is electronic and I have difficulty reading it, so I used my experience and installed it without the Instruction Manual.
View detail
Type ordered and …….
It took me a while to do the work because I had to remove and install the tires in order to replace them.
Mr. WeBig…… Do you check the contents of the product once it arrives from the supplier?
It's not the Type I ordered.
I didn't return it because I had to wait quite a while for it to come in and I was happy with either Type, but this is a return item.
View detail
Fits: HONDA CRF250R, HONDA CRF250RX, HONDA CRF450R, HONDA CRF450RX, HONDA CRF450L
UFO UFO Fork Slider
This one was for a crf250 motocrosser, but I found information on social networking sites that it could be installed on a crf250md47, so I bought it. However, it interfered with the front fork and I gave up on installing it. It was a pity. View detail
This is the kind of Screen
I personally did not like the design of MT-07 after most of the screens were installed, probably due to the mounting position of the Light, but with NAKED, it is like a battle against wind speed at high speeds, so I had no choice.
Since we wanted to avoid a large, prominent Screen, we chose a Type with a transparent top.
Middle type in terms of size (Small Type?) Although it cannot be said to be strongly effective, it seems to have slightly reduced wind pressure hitting from the chest down at high speeds of 80 km or more, but a larger type would be better if the wind protection effect is to be enjoyed at the largest possible size.
As for the installation, I think it is easy and even girls who are not good with Machines can do it.
Since the meter is in the front of the car, there is space for a pair of shoes between the meter and the screen, which is convenient for placing gloves or other items.
You could say it's a waste of Space, but … sweat.
View detail
Fits: YAMAHA SR500, KAWASAKI ZEPHYR750 RS, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, YAMAHA SR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR400χ
It makes you look pretty.
I think the price is reasonable and it is a good product for casual makeover. I think it looks cute.
Installation was a little difficult in positioning.
The drawback is that the LightBody of the car body gets small scratches at the installation pin if the positioning takes too much time and has to be redone.
Rather than putting it on and taking it off, it might be better to leave it on after putting it on.
View detail
Functional Parts for a Bland Bolt
[How is it used?
For fixing Bolt of License Plate of SEROW250 which is used for mountain play.
Just by replacing the inorganic fixing Bolt with this product, it will look better, and it can also be used as a Net fixing Hook for when you have a lot of baggage. Two for the price of one. PARTS.
Was the one you received as per Image?
I saw a friend's Motorcycle that had already installed this product when I didn't know it existed yet. What is this aluminum color that looks like a very small version of the Tezuga?" When I asked him about it, he told me that it was a product installed for the above-mentioned purpose, so I immediately took a crack at Ideas.
The product was as per Image because of such a process of purchase.
Was the installation difficult?
The difficulty level is low because all you have to do is remove the bolt that was attached to the License Plate and install this product, and I think that anyone can easily customize this part.
How was your experience with it?
Most of them are free dress-up parts, but they are used for fixing the Hook of Net for Motorcycle when we carry a lot of luggage with Motorcycle, which happens a few times a year or not.
It is seldom used for functional purposes, but it is useful when it is.
Well, it's a bit of a duplication. Color Anodized Aluminum Collar Dress-upSmall things.
[Included Parts:were they on?
As you can see in the picture, each color Aluminum Collar, Cap bolt (length is about 20mm?), Nut, Nylon washer×2 and 1 piece of Iron Washer are included. and Nut and Nylon washer×2 and 1 piece of iron washer is 1Quantity:Set, and itsQuantity:Two Sets are included in the package.
[Was there anything that disappointed you?
My friend who used it before me bought the Red one, but after about a year or so the Anodized staining faded and it became just Silver, so he painted it Red with plasticolor and dyed the hollow side line White (it was exactly the Image of Zunga).
Anodized light colors may fade quickly.
Other items that would be helpful
Point and hang of installation
Even though the collar is sandwiched, it is basically a fixed Bolt. "Tighten with the proper Torque." I don't think there is a problem as long as the
"Loose and falling off." If you are concerned about the "Mere Old Man", it may be a good idea to replace the existing nut with a Lock nut.
[Availability and clarity of the Instruction Manual
No Instruction Manual, as noted above. Bolt & Nut+α for fixing So no problem.
It can be used not only for fixing License Plate, but also for fixing M6Size, so it can be used in various ways depending on each individual's Ideas.
[Notes]
Not particularly
[ITEMS TO BUY TOGETHER
Basically, no.
Bolt & Nut, Aluminum Collar, and Washer in Quantity:The set is complete, so if the purpose is to fix the License Plate, this product is all you need.
[Opinions and requests to Manufacturer
2Quantity:Considering that the Set costs about 910 yen, I would like to request a more UV-resistant dye.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR
Cosmo
Note that the OEM LED Blinker has a Large Coupler and will not fit through the wiring hole.
Other than that point, I'm glad I bought it.
View detail
Wind pressure prevention, mounting △
as per Title
Nothing wrong with wind pressure protection.
However
Part of the Screen interferes with the Brake tank on STD Handlebar
Light interference when changing the angle of the Handlebar.
Therefore, I changed from STD Handlebar to one with an increased BEET aperture angle, but I could barely get it to a position where it did not hit the tank when the Handlebar was turned off.
Screen and Brake tanks with some Clearance.
In the end, the Handlebar will only feel pulled back, and there will be no height flexibility at all.
Are you sure it's for a specific car model?
The build quality was solid, but the finish around it looked a little crude.
View detail