Reviews
For additional Helmet mounting location
Purchased Helmet to attach it to places other than Mirror.
Installation is very easy.
Simply remove the Bolt from the Number and attach the PlateHolder together with the Bolt.
There is no need to add any other Bolt or Screw.
Anyone can install it in 5 minutes.
This time, I installed it on YOSHIMURA's Fender Eliminator Kit instead of OEM Fender,
No glitches or problems at all.
Also, I installed it with the supplied bolt, but other License Plate Bolt should be no problem.
I think
The construction was quite solid, thicker than I expected and Firmly.
The surface finish is also Beauty.
Helmet holder is Quantity:Pair (for Left and Right) Either can be attached.
Easy to remove and install.
The key part is a bit weak due to pushing, but that's about it.
It's not so much to prevent theft as it is to keep the Helmet on when you leave the Motorcycle for a while.
I personally don't care about it because it is the thing of the
I also installed a Holder on the SIDE of the car, but when the Exhaust System hits the car and it is immediately after running, the Holder is not installed.
It was a little difficult to use, so it is nice to be able to put it on without hitting the Exhaust System.
However, it does hit the Tire a bit, so those who are concerned about sogginess may need to take some measures.
Also, if you are in a windy place, the Exhaust System will sway quite a bit and hit the Exhaust System, so be careful there as well.
The supplies do not stand out as a Custom in appearance.
But the installation is easy and useful.
On the other hand, because it is inconspicuous in appearance, it is not so conspicuous in Styling and Silhouette.
It's good for people who don't want to change.
If the price were a little lower, the cosmetics would be perfect.
View detail
All about decorativeness
It's completely decorative only Parts.
The area is large and the dress-up effect is high.
Anodized texture and molding is also good
The gold color is quite flashy, but since the OEM is ordinary resin, I think it is good to have a sense of luxury in other colors.
The color is similar to SNIPER's Gold, and compared to BABY FACE's Orange Gold, it is more Gold! It is a feeling. However, it is not enough to feel uncomfortable. Rather, the Frame hole is sandwiched between the BABY FACEfootpeg and the frame hole is bothered…
Weight:180g for OEM (including Chain Slider) It was 420g against. I think that the weight is not so bad, but I will remove the OEM Chain Slider, and I am a little concerned about whether it will affect me.
I have a k-factory shift spindle holder installed and there is no interference or other problems. Accuracy is good.
The price is quite high, but I think it is reasonable because the machining accuracy is good, the installation is fine, and the amount of material is high...
Luxury, or rather luxury Parts…….
View detail
Your neighborhood AGRAS is the best in the world.
I use it for KATANA which I own jointly with my brother. I went to AGRAS directly to buy it and asked the president to put it on because I really wanted to use an excellent product of AGRAS in my neighborhood, and I found a not so conspicuous but functional one. I can always see the condition of the front sprocket, and there are many Merits! View detail
Agras Sprocket Cover on '98 Bandit 1200
The is a beautiful item that allows one to remove the slave cylinder without removing the sprocket cover. It is machined beautifully and comes with fasteners and spacers. It took me 10 minutes to install. View detail
Does it vary from one individual to the next?
Purchased at the same time as the Lear Fender Eliminator Kit at a Motorcycle store After the installation, the person in charge will If you take Balance, you'll be too close to the Right Report When I check it, it is a few millimeters of LeftTire because it is not centered correctly It seems to be bent all over, and if we don't fix it somehow, it seems to scrape the Tire and run I don't think this is the whole product, so it looks like I've bought HaGap It's a shame because this makes me less satisfied overall View detail
Parenthesis is better
The OEM Fender was tacky because it covered too many Wheels, and now it's Stylish
A related product, Stubby, is also available, but, well, you know, it's your choice
I was happy enough with the Fender alone
Yes, there's an added bonus that this Fender makes it easier to remove the Tire
View detail
light!
It is light.. Installation was also easy.
In the empty space after removing the OEM's Chain case "Buy AGRAS Sprocket guard!" There is a feeling.
There is little space between Tire and Tire's beard is hitting.
Because it is Carbon it takes about 1 month for delivery.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
License Holder is not attached
GSX1300R (08-10) In the picture of the product page of the product, it looks like License Holder is attached, but it does not come with. Also License Holder is not integrated. It is an option..
I was disappointed, but I was convinced by seeing the real thing, fluffy Carbon light.
Manufacturers of other companies have brackets to be fixed, LED lights are often like hinges for angle adjustment, but AGRAS is OEM ShapeMaterial : I just said CarbonShort fender. The angle of License Plate is fixed.
For installation, remove Rear cowl and OEM Product, stop 4 Screws, return Rear cowl and complete.
License light is just inserting OEM's Connector without processing.
Dissatisfied is that Tie Wrap that was removed when attaching License light was not attached and Carbon, so it took about one month for the delivery date.
When Maintenace Stand is used, the bar interfered with Normal fender, but you can use it without problems.
View detail
It is quite conspicuous
When porting R1Clutch cover to FZ1 Fazer, we purchased this item because there is no face White in OEM Parts Number.
Clutch Wire leaves from the top and goes into Frame It does not attach to OEMCover of FZ1, it is for Type where Clutch Wire comes out from under R1.
Small I thought that it was an inconspicuous part, but I bought it, but it has quite a presence.
Installation is BoltQuantity : Easy with only 2pc, if you keep the basic Torque (Since the bottom is Alie's Die-casting, I think that if you tighten it all you can easily screw up the Screw hole)
Making is also beautiful and very satisfied.
However, although it was possible to personally as a result that it became conspicuous beyond imagination, I thought that people who do not like it would not like it.
The price is also slightly higher ...
Regarding functional performance, is rainy day or something effective? ... It is totally unknown.
View detail
Billet parts are roman
It is the installation to 2007 type R1.
I thought of purchasing for Dress-up.
The notation here corresponds to 09 - 10, but as long as you check ProductNo at Manufacturer 's Site, you can see that it corresponds to R1 in 2007.
Mounting is only to exchange OEM Parts. Since the attached Screw was shorter than the one of OEM, I used the OEM person.
I selected Silver according to Slider 's Base color out of 5 color' s colors It is a nice feeling.
Prices are somewhat higher so we recommend purchasing with Point.
View detail
The fit , the finish , the all important Busa shape , Agras has ticked all the boxes , really a superb piece . Simply the best Gen 2 fender on the market .
The fit , the finish , the all important Busa shape , Agras has ticked all the boxes , really a superb piece . Simply the best Gen 2 fender on the market . View detail
Row Fender
It is attached to KSR 110 of 08 year.
Image changes from NORMAL, but since there is no such thing that splashed water will not hit Engine, I think that it is completely dependent on personal preference.
As for installation, there is only Exclusive Design and if there is only Hex wrench anything can be installed without problems.
Since it was White Gel processing, I painted under Spray after matting with Surfacer and matting black.
View detail
Fender Eliminator Kit
Compared to other Kit, because it is Reflector position, I think a little longer. Angle of Number can not be changed.
Since it is unnecessary to remove Seat under cowl, installation was easy.
View detail
Fits: DUCATI ST4, DUCATI ST2, DUCATI MONSTER900, DUCATI 916, DUCATI 900SS, DUCATI 888, DUCATI 851
It looks nice
OEM is Gray 's PlasticCover, and I could not say that Parenthesis is good for flattery, but Refreshing and Parenthesis has improved.
Installation was also easy with Bolt-on.
View detail
I am disappointed with the purchase of this sprocket cover due to the fact that there was no hardware or spacers to mount it! The only thing in the box was the cover! That means I have to source the bolts and make some spacers on the lathe to even be ab
I am disappointed with the purchase of this sprocket cover due to the fact that there was no hardware or spacers to mount it! The only thing in the box was the cover! That means I have to source the bolts and make some spacers on the lathe to even be able to bolt it up. NOT COOL! I have bought quite a few of their products in the past and was always impressed with the completeness of the products that they sell. Just not this one for the price. View detail
Structure is very good.It is so good that it improves compared with the thing of other Manufacturers although there is also that the position of a hole has shifted. finishing is also beautiful and also has intensity exactly.Since a pure grade enters as fo
Structure is very good.It is so good that it improves compared with the thing of other Manufacturers although there is also that the position of a hole has shifted. finishing is also beautiful and also has intensity exactly.Since a pure grade enters as for the
load, there is no dissatisfaction in particular.
View detail
Although it is said in the description that "exchange is possible at the cap made of resin of frame both sides, and bolt on", two aluminum caps were only sent. However, the cap made of resin of the side face of Ninja250r is every two pieces (a total of fo
Although it is said in the description that "exchange is possible at the cap made of resin of frame both sides, and bolt on", two aluminum caps were only sent. However, the cap made of resin of the side face of Ninja250r is every two pieces (a total of four) to right and left.... I only can change the one side to an aluminum cap, but it becomes ill-shaped. Moreover, from the beginning, a tapped hole is damaged. Although it is bad not to confirm as there is only a picture of an upper cap and it does not have the description of the number of item, either. It is 6825yen and I think it is too expensive, the evaluation is one star. View detail
Since a rear fender looked heavily greatly as for SV1000, it tended to be attached, and it tended to be felt refreshed. Moreover, to carbon favorite around 40, it is attractive. Although it was not so difficult, the pin which interferes in a rear
Since a rear fender looked heavily greatly as for SV1000, it tended to be attached, and it tended to be felt refreshed.
Moreover, to carbon favorite around 40, it is attractive.
Although it was not so difficult, the pin which interferes in a rear cowl and stops an inner fender was not stuck, but three attachment has been spoiled.
Although it adjusted and entered somehow, I am a little sorry for the crevice between a rear cowl and an inner fender to open.
It is as natural as the appearance after attachment mistakes that it is pure.
However, a thing with a large cover of a number LGT has a part of sense of incongruity.
Since it is satisfactory in general, they are four stars.
View detail