Reviews
O-ring is Garbage
I thought I read that TENERE fit up to 23, but I bought it.
No problems with installation, no interference with brake pedal etc.
There is no particular change in operability, but it seems to be easier to apply the ankle area to the vehicle body.
The other thing I would like to see is the appearance and the ability to put a lid on the Pivot shaft mounting.
There is nothing wrong with the accuracy of the product itself, but the weatherproofing of the O-ring that comes with it is very weak! I don't think it will last more than 2 months.
It is possible to substitute the O-ring fixing part with Tie Wrap. However, I would not use this material because it does not look good.:I have replaced it with a SiliconO-ring and am using it. So far there has been no deterioration.
View detail
Frame protection and improved gripping
Off-road motorcycles tend to peel off the paint on the frame when riding in Boots, because the frame is inevitably caught between the legs when standing.
From the viewpoint of preventing paint from peeling off and rusting, it is recommended to install frame guards.
Installation is easy because it is only fastened with a washer (sturdy rubber), but side covers and sprocket covers cannot be installed properly unless they are removed, even if it is a pain in the ass. It is a bit of a hassle, but it would be better to remove the Cover before installation.
View detail
Simple but good performance
It looks good, but the grip is good, so there is no burden when standing due to the grip of the boots and chassis. Installation is very simple and I think it's good because it prevents scratches.About quality and texture View detail
When the Center Stand is installed, a little effort is required.
The Instruction Manual indicates that the cover under the tank must be removed for installation, but it can be installed without removing the cover.
On the Left Side, the lower claw is first fitted and then fastened with two bands (Large and Small).
The Left bottom of the Right Side Cover interferes with the Center Stand, so it must be trimmed, including the claws.
I think you should cut at the base of Radio pliers and Cutter to Beauty!
Then fasten with Largex2 Band
Bundling Electrical Cord Covers Next Needle Gold Makes Banding Easier
View detail
When the Center Stand is installed, a little effort is required.
The Instruction Manual indicates that the cover under the tank must be removed for installation, but it can be installed without removing the cover.
On the Left Side, the lower claw is first fitted and then fastened with two bands (Large and Small).
The Left bottom of the Right Side Cover interferes with the Center Stand, so it must be trimmed, including the claws.
I think you should cut at the base of Radio pliers and Cutter to Beauty!
Then fasten with Largex2 Band
Bundling Electrical Cord Covers Next Needle Gold Makes Banding Easier
View detail
good-looking
It sticks tight like OEM. The ankle grips are good and easy to stand on. The ORing for the fixation may break someday, but it can be fastened with a bundle of wires, and the mechanics at the motorcycle shop liked it. View detail
Wow that's cool
[How is it used?
Dress-up
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy
How was your experience with it?
Safe in the event of a fall
[Included Parts:were they on?
(after the -te form of a verb) not ..
[Was there anything that disappointed you?
(after the -te form of a verb) not ..
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FE250, HUSQVARNA FE350, HUSQVARNA FE450, HUSQVARNA FE501, HUSQVARNA FE350S, HUSQVARNA FE450S, HUSQVARNA FX350, HUSQVARNA FX450, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TE150I, HUSQVARNA TE250I, HUSQVARNA TE300I, HUSQVARNA TX300I, GASGAS EC250, GASGAS EC250F, GASGAS EC300
Frame guard installed TE??FE
The standard Achal ScrewFrame guard.
Cover range is wider than OEM.
Blue type Frame guard on the TE of Blue type Frame,
Black type Frame guard is attached to Black type Frame FE.
Remember to remove the OEMParts collar and use it.
View detail
BITTER X-GRIP
Fits well with 2023 Honda crf300l. The delivery of the product is fast and the quality is satisfactory. It is also easy to mount the product, so anyone can mount it. I like the frame protection and design the most. View detail
Beware of O-rings
Parenthesis has improved, and I'm generally happy with it,
After a few months, the O-ring deteriorated Quantity:Pair (for Left and Right) I noticed that they were cut off one by one.
If two O-rings on the Clutch Side break off, they may drop out.
Please note
So I re-fastened it with a thin needle Gold.
View detail
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
For Smooth Shift change
There is a hole on the left side of the frame for attaching the swingarm, and the work boots would often get caught on the convex part of the hole, causing shifting errors (this may not be a problem depending on the finish of the outer side of the boots). (This may not be a problem depending on the finish of the outer side of the boots.)
I happened to see it installed on a vehicle of the same model that I saw, so I ordered it and installed it.
Hexagonal Wrench was used for part of the installation, but most of the installation was completed by tightening Tie Wrap and cutting the excess part with Nipper.
After the test ride, I confirmed that the ankle grips are easier to do and the snagging of the Boots has been eliminated.
However, when removing the Swingarm for servicing, it must be removed because it is in the way, and a new Tie Wrap is needed in that case.
I don't know how durable it is, but it makes it easier to ride and I appreciate the product.
View detail
Bitter Bitter X-GRIPFrame protector
Material:It is plastic, so the texture is not that great, but it is sufficient for the purpose of preventing scratches on the Frame.
The rest is attached with rubber, but it is so tight that it will not fall off easily.
View detail
It looks good, but how durable are the fixtures?
I installed it on a Black Frame with a Red color.
It's been about 3 months now, and the ProtectorBody seems to be fine, but I haven't done any Dirt running or Hard running at all yet, but the Rubber to fix it to the Frame (?) was degraded and Crack was found in it.
I pulled it lightly with my finger, and sure enough, it snapped. I looked at the other fixed points and found a similar crack on the rubber. I checked the other fixation points and found a similar crack on the rubber.
At first, I went to Home center and got an O-ring of about the same size and replaced the one that was cut off.
I wonder if it is the heat? If it persists in the future, I will consider another fix.
View detail
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
Protection as expected
For Off-RoadBoots, I bought it because the Frame is damaged.
It looks cheap when viewed on the Single Body, but when installed, it does not bother me.
I chose Silver because the Frame is Silver. I hope the Tie Wrap is also Silver.
The work is easy to do.
View detail
Frame scratch prevention
I bought this to prevent the Frame from being damaged by Boots.Color to match the Frame Collar:The base color is Gray, and the Grip is Black with a non-slip material fitted, so there is no discomfort when wearing it.
Installation is easy and the Right Side (Brake Side) The "Others" method uses only one NORMAL screw, while the "Others" method uses an O-ring that is turned on the reverse side of the frame and hooked onto the Protector's mounting hook.
I think it would be best to warm it up with a Dryer or similar to match the curvature of the Frame.
Grip by Boots felt easier, and it was also good to prevent damage to the Frame.
Mud and water can get between the Frame and Protector, so it looks like it should be removed and cleaned periodically.
View detail
Fits: HONDA CRF 450R, HONDA CRF 450RX, HONDA CRF 300RX, HONDA CRF 250RX, HONDA CRF 250R
Grip feeling Up!
[How is it used?
Used on CRF250RX '22 model. frame protector is a frame protector that only reduces scratches and damage to the chassis, but this ACERBIS frame protector has a rubber-like outer surface that improves the grip between the boots and the frame protector. It is an excellent product that also improves the grip between the boots and the frame.
Was the one you received as per Image?
The color is better than I had imagined and looks great.
Was the installation difficult?
The instruction manual, while a bit confusing, is included in the package, so I had no trouble at all.
Resin parts are inserted into the hollowed-out cylindrical part of the body and fixed with Screws. Bind it to the frame with the attached rubber. Is this what you want? But it is very accurate and firm, so it is totally sturdy and large.
How was your experience with it?
The Grip feel is totally different.
The ankles of my boots did not fit the frame properly due to the thickening of the knee side after wearing the knee brace, and I was feeling uncomfortable. With this brace, the fit of the ankle portion has been greatly improved, making it much easier to control!
I should have put it on from the beginning,,,!
Of course it serves its purpose of Guarding the Frame well!
[Included Parts:were they on?
Rubber and Screw for mounting, plastic parts for fixing Screw holder, and ACERBIS Sticker.
[Was there anything that disappointed you?
No, I'm not! I'm so happy!
View detail
Fits: YAMAHA WR 125 2T, YAMAHA WR 250 2T, YAMAHA YZ250, YAMAHA YZ125
Both Boots and Frame can be protected.
When I was riding my YZ125, the Frame and Boots rubbed against each other.
I bought it to keep both Boots and Frame down as they are both coming down.
The frames have not decreased in size, and the boots do not seem to hurt as much because the plastic is softer around the boot.
However, the Frame protector was clearly more sharpened after just one ride.
I thought it needed to be replaced regularly.
I did not feel any particular discomfort in the Knee gripetc. when I rode.
View detail
Boots slip prevention
Damage prevention for both Off-road boots and Frame. You can Grip without hesitation after installation, and I think the design is good. View detail
I love it
I couldn't help but notice that when I was on
I'm in the habit of holding the body down with my calf.
I thought the Frame paint would come off.
I was trying to divert the Heel Guard from another car.
I was thinking about it, but there are a lot of Frame guard
I found out that it was out there and
It was a shade that didn't stand out too much.
I chose this one.
As for the installation, the Change Pedal side
I felt that the lower part was a little difficult to install.
It was installed without any problems.
The Brake Side was installed in a few minutes, so it was very easy.
If you have tools such as Socket, there should be no problem.
I gave the Change Pedal side 4 stars because there was a gap at the top of the pedal, but the Brake Side was good with no noticeable gap.
The tint is a bit darker than the Frame color, Silver.
I didn't particularly care for it, so I was satisfied with the product in a casual way.
View detail
Fits: BETA RR 2T 250 RC, BETA RR 2T 300 RC, BETA RR 4T 350, BETA RR 4T 390, BETA RR 4T 400, BETA RR 4T 430, BETA RR 4T 450, BETA RR 4T 480, BETA RR 4T 498
Very comfortable to use!
I replaced it because it was worn out a lot with the new Boots.
I made a new one with the same one this time because it has a footpeg Grip feel and is friendly to Boots.
View detail