Reviews
… Failure.
It is not attached to the '23 model because of a model type mistake.
I gave it to a friend.
View detail
![Stand Height Bracket [Kickstand Shoe]](https://global.webike-cdn.net/photo/impression/f0/f0f22f0d19791e25f9a089ebba4b8f68L.jpg)
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000
The product photo and the actual product are too different.
The product picture is too different from the actual product received.
Notes. The photograph is an Image and may differ from the actual product. I think it says something like that, but it is too different.
I paid almost 9,000 yen expecting to see a picture of the product, and this is not what I got.
depending on the person "There's R&G." And "It happens all the time with R&G." It is said that the WeBig side of the product listing
I think it's a problem, don't you?
Please compare the product photo with what you actually received.
The picture was taken at Image..." I don't think it can be done.
View detail
It looks good, we just need to improve the accuracy of the parts!
I think it looks good, but the industrial accuracy of Level is disappointing. The screw hole was also visible from the outside, and when I tightened the screw, the carbon on the top seemed to crack, so I put Sponge on it to make it tighter. The screw hole was also visible from the outside. It's a shame because it looks good. View detail
Hmm
I bought it because of the design. The design is very attractive. I tried to cut it with a sandpaper, but it doesn't fit. The accuracy of processing is not so good. The screw hole is also out of alignment and I can see the screw from the outside. (^^) View detail
Good in cost, good in design, poor in function
Cost and design are good, but when you try to install it, you'll see that the tip of the STAND is It got stuck and the tip bolt of the Stand End could not be attached As a result, it is fixed hard with two rear bolts It is running in the state of worrying that it will fall off at any moment
View detail
Fits: BMW R nineT, BMW R nineT Pure, BMW R nineT Racer
It's easy to drop out
It fell off and was lost two months after installation
It was re-tightened twice during installation and is structurally prone to loosening from the beginning at the Manufacturer I think you should apply a loose-proofing agent to the Bolt
I was hesitant to re-purchase it because the costumes are terrible, but after operating it for a while without it, the parking place It's not that inconvenient and looks awkward if you choose to do so, so I decided it wasn't necessary
View detail
![Stand Height Bracket [Kickstand Shoe]](https://img.webike-cdn.net/catalogue/images/50737/22748760_1_TS.jpg)
Fits: TRIUMPH TIGER, TRIUMPH TIGER, TRIUMPH TIGER
Material is good but can not be installed.
I bought it for TIGER 1050, but I can not stop Screw as it is because the tip of STAND does not fit. There was no notice that it could not be installed unless it was cut. View detail
It is too thick!
Maybe it depends on the type of car, but the geta was too expensive for our vehicles.
It is indeed the primary objective of this Items "It is not buried in Left Side" Has been achieved, but if you mount and stand on Asphalt or Concrete, the Motorcycle stays upright as it falls to Right even if the wind blows.
I was disgusted by searching for earth and grass on the road and stopping it..
View detail
Although it was not easy to become obstructive, the diameter of attachment of die length of a hook with a stand did not suit, but it rolled the rubber sheet and corresponded. From the start, if I mean to, a rubber sheet should also be attached by atta
Although it was not easy to become obstructive, the diameter of attachment of die length of a hook with a stand did not suit, but it rolled the rubber sheet and corresponded.
From the start, if I mean to, a rubber sheet should also be attached by attachment.
View detail