Reviews
Fits: YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP
parts shortage
There were no defects in the product.
However, parts were missing.
I think I am at fault for taking so long to open the order and for starting without NumberRinging all the parts. I ordered only Grommet today.
It is impossible to install until the part arrives, so it is not possible to put it on.
If you are considering purchasing, please make sure to check the part.
View detail
Cowl drilling required
I ride a CBR600RR (2009).
I purchased this product because I was told it was compatible, but I could not install it without drilling out the cowl.
Fortunately, I did not have to drill holes by diverting the Slider Bracket that I had originally used, but of course I had to choose and purchase the Bolt myself since I could not use Included Parts:.
If you purchase the product, you should be prepared to drill holes in the Cowl.
View detail
Absolutely WRONG Slider Parts
Webike product page states they are for Ducati SF V2, but in fact they FOR PANIGALE V4 SP2!!! First the physical shape and installation points of received parts DO NOT match the photos shown on Webike prodcut page (which use an installation example of Ducati SF V2). Second the wrapping lable of the shipped parts clearlly stated "PANIGALE V4 SP2", NO words about SFV2. This is a completely stunned and wrong experience. View detail
Fits: YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15, YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15
No instruction manual?
There is no instruction manual.
I am not sure about the installation unless it is at least illustrated for local use.
Can you do something about it?
I can't even comment.
View detail
On the first Touring after installation?
During the first touring on the highway after installation, the Masaka Pipe broke off at the base and flew away. View detail
Instruction Manual not included.
The lack of an Instruction Manual makes installation a little tricky.
Holes in DURACON are smaller than those in Bolt, so drilling is required.
Because the amount of threading on the Hexagon Bolt is small, the screw cannot be tightened enough and the slurry sleeve becomes free, so it is necessary to prepare a separate bolt with all screws.
View detail
Please change the photo.
Only the bottom two parts are coming.
If you think you can buy what you see in the picture, you're out of luck.
If you don't change the photo, it's a scam.
Please replace the photo ASAP.
View detail
Fits: KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT EDITION, KAWASAKI Ninja ZX-25R
Garbage, maybe.
DURACON was broken as a result of being pushed and collapsed by another car while parked.
Even if only DURACON is replaced, the cost of parts alone is about 7,000 yen on the One Side.
If you are not a Kawasaki OEM believer, I would recommend other companies' products.
View detail
I will not buy it again
The Bolt that came with it was shoddy and broke during installation.
not worth talking about at all
View detail
Fits: YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15, YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15
It was impossible to tighten as shown in the picture.
Bolt to be tightened or Washer is missing View detail
Fits: YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15, YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15
Cannot be installed due to inadequate parts.
I am asking for installation instructions as soon as I buy the product, but I am not sure how to proceed.
After a few months, I haven't heard from them and can't put them on.
I took it to Motorcycle shop and they said, "Oh, we need more parts.
What about inquiries?
request a reply as soon as possible
View detail
Fits: YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15, YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15
Lack of parts and cannot be installed.
Tried to bring it to Shop to have it installed, but it contains parts, Bolt that cannot be tightened and cannot be installed.
Shop told us that they are missing parts.
The Bolt that attaches the steel back plate to the Right Side to the Engine has a Bolt that does not close.
As soon as I bought it, there was no Instruction Manual and I immediately contacted them with an inquiry, but they still haven't resolved the issue!
I was forced to go to Shop to have it installed, but there were no parts that could be installed.
View detail
Lowest
The length of the bolt in the Included Parts:section is not correct and cannot be installed as it is. This may be the case with parts made overseas and installed on a foreign car, but we are honestly disappointed with the condition of the parts despite the long time it took to receive them. View detail
![[Repair Parts for Engine Protector] Pat Unit Φ50](https://img.webike-cdn.net/catalogue/images/107688/79952_TS.jpg)
Fits: Others For Engine protector, その他 For engine protectors
One and done.
After one use, the entire DURACON part came off.
I will give it a low rating because it was smashed and atrophied before it could be cut.
View detail
![[Repair / Option Parts] Frame Slider](https://img.webike-cdn.net/catalogue/images/76929/TS-FS-203_01_TS.jpg)
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3
A notational error?
The R-25 fits models 15-21, but it cannot be installed on models 19-21. View detail
mistake
(2021/9/12) When I stop at a traffic light, or when the car in front of me moves in a peculiar way, etc., I hit my shin against the slider when I try to put my foot on the ground in a hurry, although it may be my habit.
My shins are still swollen.
If you are not running Circuit, I would recommend something other than OEM or motorkuman.
In addition, because it is ugly only with Slider, I bought an expensive Sticker separately. It is so cheap that I think that it is not good even if it comes with it.
View detail
Fits: YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15, YAMAHA XSR155, YAMAHA V-IXION, YAMAHA MT-15
Cannot be installed→No support
Bolt is too long to install.
I reported it in detail. "Checking with Manufacturer." The last time I heard from
I haven't heard from him in two weeks.
When installed, the screw holes in the engine block will be crushed.
Be careful
View detail
KIT parts cannot be fixed alone.
It was a ridiculously defective product for a not-so-cheap price of $6458.
KIT parts alone cannot be fixed because the fixing bolt (M8) does not match the hole diameter (M10) of Shaft parts.
(There are too many gaps and rattling).
I thought about returning it, but that would be a pain in the ass, so I'll just add my own parts to it. 。
I bought an Aluminum Pipe (10mm OD, 8mm ID) at Home center and made a Spacer to fill the gap.
Added Washer so that Bolt's Torque can be applied without difficulty. 。
It's a shame, because it would have been a great product if I could have added the parts and installed it properly myself.
View detail
How do I cancel an order?
I got an email that Engine slider for W201217A2231SR400 is out of stock from Manufacturer.
I cancelled my order, but I could not execute it from the web.
View detail
Not available
Because the processing dimensions are wrong, the part of the Left Side is lifted up to the Frame Shall
I had to bite the Screw to keep it firmly in place, so I had to bite the Washer
Crack enters the base of the Right Side after less than 1,000 km of driving I almost dropped the SliderBody while driving
This is a flawed product that only looks good
View detail