Reviews
Purchased for appearance.
Purchased for appearance.
It is not a cheap overseas product, but a reliable AGRAS, so it is a beautiful AnodizedBlue. The quality is very good! I think the price is a bit high. I would be satisfied with Large if it were a little cheaper.
I have it on a different Motorcycle as a decoration, but it has never tipped over, so I don't know how effective it is. But I think it is better to think of it as a decoration.
View detail
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
Perfect appearance
I'm not mocking it up,
Effectiveness is unknown,
It is better to think of it as a dress-up,
And to think,
I think the price is high.
View detail
Better than nothing, installation hassle
The Female Screw side did not fit as expected, and I measured it with Caliper. 0.5 millimeter. I managed to insert it by shaving the average thickness with Belt Thunder.
Personally, I think Other Brand Product is the way to go!
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I'll never roll over …
I'm going to install it with the idea that it will look a little better before it falls down. View detail
Fits: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
Easy detachment!
Rather than a rear slider, the Axle Shaft was installed to make it easier to attach and detach the Axle Shaft.
It can be used as a handle like Doorknob when pulling out shafts, and when inserting shafts, the triangular pyramid shape makes it easy to insert the color, etc. without resistance.
Of course, it would also serve as a Slider, but currently it is benefiting from the detachment process.
View detail
Fits: DUCATI STREETFIGHTER V4 S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4 R, DUCATI PANIGALE V4 SP, DUCATI STREETFIGHTER V4, DUCATI SUPERLEGGERA 1299, DUCATI PANIGALE 1199, DUCATI PANIGALE 1199 S, DUCATI PANIGALE 1199 R, DUCATI SUPERLEGGERA 1199, DUCATI PANIGALE 1299, DUCATI PANIGALE 1299 S, DUCATI PANIGALE 1299 R FINAL EDITION, DUCATI STREETFIGHTER V4 S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4 R, DUCATI PANIGALE V4 SP, DUCATI STREETFIGHTER V4
A walking stick before you fall3
[How is it used?
We chose this product because we wanted to protect the Swing Arm.
I chose Red to match the body color and am satisfied with the color, which is ideal.
Was the one you received as per Image?
Swing Arm is more overhanging,
Protection is not complete.
Was the installation difficult?
A handling Instruction Manual is included, which describes the torque for tightening the fixing bolt.
I'm not sure if mine was an outlier or not, because the Left Side Bolt length is too short,
Fixed parts had to be machined.
How was your experience with it?
Unlike the Front, it rotates with the Wheel,
Easy to loosen, Locktite was applied to the fixed Bolt.
[Included Parts:were they on?
A handling Instruction Manual was included in the package.
[Was there anything that disappointed you?
The key Swing Arm cannot be protected.
View detail
You have to remove the shaft and install it.
The cap on the Right Side is clearly different in size from the Left Side and hits the GunGun so hard that it is impossible to install unless the front is raised and the shaft is pulled out. View detail
The Z900rs requires some modification.
First of all, the design of the text is different between the image and the real thing, but I didn't mind it too much.
The Left Side Lock nut is not included in the kit, so you need to prepare it by yourself. I first selected "Pitch normal" for the Left Side Lock nut and failed to use it. (You are solely responsible for your own mistake.)
The lock nut of the M18 was too tight for the Left Side Protector, so I had to grind the inside of the Protector a little to fit.
Quantity:Pair (for Left and Right) The bolt for penetrating the "B" is also a little long, and it is difficult to apply the tip cap, so both ends were shaved off.
Note that the z900rs does not have a bolt on and requires some modification.
View detail
Fits: DUCATI MONSTER 1200, DUCATI STREETFIGHTER 1098, DUCATI MONSTER 1200 S, DUCATI MONSTER 1200 R, DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 950 SP, DUCATI HYPERMOTARD 939, DUCATI HYPERMOTARD 821, DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 950 SP, DUCATI HYPERMOTARD 939, DUCATI HYPERMOTARD 821
Simple
I installed Lightech front wheel axle slider on Ducati StreetFighter 1098 with aluminum adaptors include. The installation is simple, nylon slider body is a bit slim compared to another axle slider such as SW motech. View detail
Incompatible with ’23RnineT
First, it does not fit the ’23 RnineT. The Axle seems to be shaped differently and the One Side boss does not fit inside the Bolt of the Axle.
So I cut off the boss and managed to use it.
Disappointing result for the time it took to deliver.
View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1199Panigale, DUCATI 1299Panigale, DUCATI DIAVEL, DUCATI StreetFighterV2
Simple and inexpensive.
I thought I had researched and ordered it, but the PanigaleV4S was not among the compatible models. Sweat
Item number:006-AD007
The length of the Long Bolt was sufficient, so we cut the transparent tube of the Long Bolt by 1 cm to match the length.
It can only be installed if you have a 10mm deep socket.
I am surprised that neither the product introduction nor the Review mentions SheepSocket.
I went to Astro to buy one.
Single Item:about ?,300, Quantity:It is about 2500 for a set.
View detail
I'm not particularly indebted to you.
I put it on because it's kind of a standard product, but it could have gone either way.
It would be self-satisfying because normal people don't look at these places.
MotorcycleParts, as you might feel if you're also tinkering with cars.
There are a lot of smalls and not as Impact as a car.
For example, Squid Ring.
View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI ZZR1400 (ZX-14)
No fit feeling
It was a compatible model, but it was too loose to stop, so we wrapped a rubber plate around it and adjusted it.
Split Pin cannot be installed because it is inserted in a hollow Axle.
View detail
Motorcycle Dress-up
I bought this for my M10 but it was for my M8. View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10RR, KAWASAKI ZX-10R SE
Rear sliderGreen color
I like Rai TEC products and use them in various areas.
Anyway, it looks beautiful and has a high dress-up effect.
I bought an additional Rear slider because there was no Rear slider in the Birdock Star product line.
Each part is Green color, which gives a sense of unity.
View detail
It's discreet and nice.
I put on the front axle protector, although there are pros and cons.
The image is after installation, but it is not very noticeable and looks good.
The damage may increase due to the longer sliding distance, or it may get stuck and increase the damage due to the lever principle, but we assume that the speed is not too high.
It is a 13mm Nut, but normal Glasses cannot be tightened because the Nut goes inside.
Also, when you close the Quantity:Pair (for Left and Right) If you don't tighten it evenly etc., one Bolt will pop out.
I haven't experienced the effects. No effect." The company is committed to
I hope you don't feel it.
View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R
It doesn't fit even if it fits.
Purchased because the shape was similar to WSBK.
The weight was approximately 150 g.
Type through the axis is Quantity:Pair (for Left and Right) It is difficult to remove it from the "QUANTITY".:Pair (for Left and Right) Easy to work with because it is independent.
However, as expected of Made in Italy, the nut side is loose even when tightened to the max.
I dealt with it by wrapping a roll of self-adhesive Tape, but it stuck when I removed it and looked Large strange.
Also, after I bought it, I realized that I can't make a split pin because it is not a type that is co-tightened to a nut.
The cup is a cup type, but it is not co-tightened, so it looks like it is on top of the shaft, and it looks unattractive without a sense of unity.
View detail
Fits: HONDA GROM [Grom] (MSX125)
Looks better than Slider
This is one of the Parts that I purchased to make the Grom BlackGold.
However, after I bought it, I realized that I had to remove the Tire in order to install it.
I had neither the equipment nor the experience to remove a tire from a motorcycle, so Jack from "for Vehicle" and I managed to install it by brute force.
Equipment and tools are Large things.
View detail