Reviews
New car installation
It was installed at the installation store when I purchased my new car.
May be difficult to install by yourself
View detail
I feel protected.
The texture is good, and the E/G area is well protected. I had a problem with the plug hole in the pipe, but it's nothing to be concerned about.
Installation is not difficult as long as the through bolt in the Center Stand section is inserted.
View detail
beautiful & practical engine guard
Installed the Active engine guards on 2019 honda cb1100RS. the fit and finish is perfect and the engine guard is very high quality. highly recommended! View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI KATANA, SUZUKI GSX-S1000GT
Parenthesis good!
The design is very Parenthesis.
But I feel it is a little expensive. However, it is well made for the price.
View detail
Protective Crash Frame
About quality and texture: aluminum and single wielded together to form the frame - Great About the feeling of use Products to buy together: None Difficulty of installation: 6/10 - require jack to push up the engine Cost performance and comparison with other products: Normal - around the same cost About shipping and packaging; PERFECT Any concerns, cautions, or advice when purchasing: The instalation was not perfect, the hole on the frame required to be widen as this messed up the alignment of the screws. View detail
Fits: BMW RnineT Racer, BMW RnineT Pure, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT
Standstill protection-Engine Guard
[How is it used?
RnineT is for a low center of gravity, so I knew it would be hard to stand and jostle, but I installed it just in case.
It's been six months since the car was delivered and we haven't had to take care of it yet. (⌒∇⌒)
Was the one you received as per Image?
We had the standard item from Dealer installed as is.
I was worried about the one from rizoma, but this one seemed to be more firmly guarded around the head.
I had this installed because I had the actual product.
I was not particularly concerned about Engine Guard.
Was the installation difficult?
I asked the Dealer at the time of delivery, so the degree of difficulty is unknown.
Probably, it should be Bolt On because it is a vehicle-specific product.
How was your experience with it?
Luckily, we have not been taken care of yet.
But this bar has more to offer than just serving as an Engine Guard.
I've seen people use it as a Mount for Fog light and ActionCamera.
There may be times when you use it that way….
[Included Parts:were they on?
I don't think there was any problem.
The optional Wonderlic ProtectionPad for Engine Guard/Tank Guard (item no. W35833-002) can be installed.
[Was there anything that disappointed you?
This does not mean that they are disappointing, but they do look a little stiffer.
That is cool, so I guess it is a preference.
I am planning to install an Under Cowl in the future, and I am wondering if I should remove the Engine Guard at that time, or keep the Engine Guard installed and install the Under Cowl. (I heard there is such an Under Cowl. I'm searching for more information now.)
View detail
สวยน้ำหนักเบาราคาไม่แพงแก้จุดบอดถ่ายรูปข้างซ้ายไม่ขึ้นได้เลย View detail
More fearless.
The actual product looks better than the picture.
Wind entrainment into the legs was reduced.
View detail
I had a bit of trouble there, but it was done without a problem.
Since I am quite a beginner, I thought it would be quite a challenge, but I was able to install it without any problems, even though it was a bit of a challenge for one person. I think it would not be so difficult if two people work together, but I guess it means that there is nothing that one person can't do by himself. View detail
inch screw threads
Bolt and nut are not consistent, such as M8 is inch, M6 is millimeter, etc. Both bolt and nut are made of ordinary material and are likely to rust easily. It will be necessary to change to stainless steel bolt etc. soon. Also, it is not possible to install the bolt according to the Instruction Manual. First of all, you have to insert the connecting plug and temporarily fix the M6 bolt nut (it is hanging), and then two persons have to work together to install the bolt nut. View detail
It was on the car body I bought from the beginning.
The end of the handlebar and the tandem footpeg were scratched by standing moss, but I think the damage would have been much greater without it. View detail
Kingdom Saudi Arabia
I ordered the rear brake pedal, it was purchased with a brake and it was one of its original parts The engine protector is also excellent and fits the sizes of my bike, fast delivery and good prices about quality and texture About quality and texture View detail
Parenthesis good
I didn't expect to fall down, but with the Engine Guard, there were no large scratches. The Engine Guard was a little conspicuous, but it was hidden by wrapping it around the engine, and I don't think it would be damaged even if it fell down again.
Expensive but recommended.
View detail
Engine Guard
I installed it immediately after receiving the car, and I feel relieved because I don't have to worry about standing on the ground anymore. A friend of mine bought a cheaper one made by a certain manufacturer, but the installation screw interfered with the body, and DAYTONA is superior in terms of design.
I have no problem with webike's fast delivery and packaging.
View detail
I guess I'm more concerned with looks.
Due to the narrow pipe and the nature of a grom motorcycle, it is not possible to install all of them on the frame, so some of them are installed on the bottom of the engine block. I'm not sure about its defensive power, but it looks great. View detail
Fits: YAMAHA DRAGSTAR400, YAMAHA DRAGSTAR400 CLASSIC
It is difficult to do it alone.
I installed it on my 99 de Raster 400 Classic.
Corresponds to all models.:The 2pc Bolt was definitely not long enough. Also, I want to move the Horn to the Engine Guard side, but it says to remove the Horn's OEMBracket, but I can't install it if I remove it.
The bolt holes on the Engine Guard side were not small at all.
Also, Quantity:Pair (for Left and Right) When I installed the footpeg on the footpeg with bolt, there is a small bolt near the Horn and there are two places to fasten it with the bolt.
Since the Engine Guard is clearly more open than the car body, it is difficult for one person to insert the Bolt through the Engine Guard, insert the Bolt into the footpeg hole, and insert the Bolt into the Bolt hole, since the Engine Guard must be aligned with the hole by itself.
And most problematic of all is the issue of Rear brake.
The de Raster has a mechanism where the Spring is pulled when the Brake pedal is stepped on and the Stop-lamp is turned on, but since the Engine Guard is tied to the footpeg, the footpeg seems to be slightly outward, so the Spring is always pulled and the Stop-lamp does not turn off. This is the problem that the Stop-lamp does not disappear.
I guess it depends on the parts that are attached, but I thought it was no exaggeration to say that mine did not fit.
View detail
Fits: HONDA CB1100, HONDA CB1100, HONDA CB1100 EX, HONDA CB1100 EX, HONDA CB1100 RS
Material:Stainless Steel and quite sturdy!
[How is it used?
I was surprised at how heavy the car was when I took delivery and immediately decided to purchase it because I felt like I was going to be standing on it in the near future.
I haven't had a standing gopher yet… (Lol)
Was the one you received as per Image?
Material:I was concerned about the weight since it is Stainless Steel, but it is lighter than I expected, yet as robust and nice as the Image.
Was the installation difficult?
The Engine Mounting Bolt was tightened with a strong torque and was difficult to loosen. After all, I searched for other people's installation information on the Net and purchased a KTC long glasses wrench separately, and was finally able to install the bolt.
How was your experience with it?
The security that protects the Engine is Large.
As another Merit, when storing the car in strong winds such as typhoons, we have been able to avoid shaking the car by jacking up the Engine Guard to the opposite side of the Side Stand to the extent that the car does not float.
As described below, the hue is a bit subtle because Frame is a Black color.
[Included Parts:were they on?
The part comes with a U-shaped Bolt and Nut.
[Was there anything that disappointed you?
The color is Stainless Steel, so it stands out against the black of the frame.
Also, when installed, the part close to the engine will burn and oxidize to a brownish color.
▼I think OVER is the right choice for a gutsy and robust Engine Guard. Some other companies protect the Cylinder, but Material:Since it is aluminum, I don't think the body of the car would be safe if it fell that badly.
Material:There is an expensive Lineup of Titanium, but I don't want to mock it up! (Lol)
View detail
Fits: KAWASAKI W650, KAWASAKI W800, KAWASAKI W800, KAWASAKI W800 CAFE, KAWASAKI W800 STREET
Design Excellence
I installed it on my w800/2016. I don't know how functional it is until it falls over, but the design is great. I am glad I chose DAYTONA Pipe Engine Guard. View detail
The description is attached and attachment was able to be attached very easily. Thank you. However, the goods price had become 799 yen part price reduction on the purchased next day, and it was the feeling which lost for a while. It was though
The description is attached and attachment was able to be attached very easily.
Thank you.
However, the goods price had become 799 yen part price reduction on the purchased next day, and it was the feeling which lost for a while.
It was thought that a few wanted consideration.
View detail
Fits: YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07
DAYTONAEngine Guard
I had it installed when I took delivery of the car, so I don't have a review of the installation process, but it should probably go on easily.
I put it on thinking it was just until I got used to the vehicle, as recommended by Motorcycle Shop, but I hardly feel any discomfort. (Personally.) The "I" is attached as it is because it is a "I".
After all, it took me a few months to get used to the vehicle, and a few times with the typical Pattern of standing staggering, but the effect is quite high.
The similar handling of the vehicle's Frame and the color Black seem to contribute to its inconspicuousness.
Also, there are plastic parts at the contact points in the event of a fall, which can be replaced in the event of severe damage.
In the event of an actual fall, the Handlebar tip and the Exhaust Coveretc. will make contact and cause some scratches, but there will be no Damage to the Parts themselves. It is not as protective as the Bumper on a learner's car, but it is not as noticeable, so it is recommended at least for this vehicle.
View detail