Reviews
Fits: HONDA PCX125, HONDA PCX125Hybrid, HONDA PCX150, HONDA LEAD125, HONDA ADV150, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA CT125CT110 HUNTER CUB
Title is not specific.
Well, if you directly connect to the Internet, you don't need it, but it is quite narrow to get in, so if you think of it as a convenient item, it is cheap and inexpensive! View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
It was easy to attach.
It was my first time installing the system, but it was surprisingly easy.
For detailed installation instructions, there is a person who is doing an Up on Minka.
Very useful. Thank you very much.
View detail
Mounted on AF24TACT
A Side Stand is useful.
Easier than Center Stand, of course.
The product can be applied.
The drawback is that installation is troublesome.
I guess it depends on the type of car, but in the case of the AF24TACT
It cannot be installed without removing the cowl and floor panel.
The installation itself was easy but very tedious.
View detail
Fits: SUZUKI swish, SUZUKI ADDRESS110, SUZUKI Address125, SUZUKI ADDRESSV125S
It is not difficult once you know where the connector is located.
I checked the Net beforehand and found a thin green connector fixed with Tie Wrap and Black Vinyl Tape behind the Speedometer Cable on the back side of the front tire! I did not remove anything in particular, but while pulling the Tie Wrap from the gap with pliers, I cut the Black Vinyl Tape with a long slotted screwdriver, and while jiggling the Black Vinyl Tape, I cut the Thin Green Connector and pushed the Male side claw with Nozzle Pliers until it became free. The Female side will be free, so insert this product there and it is done! Now you can smoothly get in and out of the car with the Engine on! View detail
I had a hard time attaching the spring.
There is nothing difficult about the installation itself, but I had a hard time hooking the spring.
CROSS CUB (JA10) The STAND itself is stored hidden in the Exhaust System, so it is a bit difficult to hook it out with a foot.
But this will give us more Situations to park.
View detail
Fits: HONDA PCX125, HONDA PCX125Hybrid, HONDA PCX150, HONDA LEAD125, HONDA ADV150, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA CT125CT110 HUNTER CUB
A tiny part that helped tidy up the unnecessary wiring
About quality and texture, I can confirm that the quality is great and that the materials used are a combination of white moulded plastic for the plug, copper spade fittings for the electrical connectors and black insulated wiring for the jumper wire. About the feeling of use, This tiny part has helped tidy up the unnecessary wiring that became exposed after replacing the original front sprocket cover with a minimalist designed aftermarket cover that was unable to hide the sidestand safety switch wiring. Products to buy together, While working on the wiring on the bike it would be ideal to also add a USB charger to your cart for the convenience of charging your mobile phone. Difficulty of installation, I can say the fitment of the side stand switch canceller for my installation was very easy due to the open access to where this plugs into the main harness and plug and play design where no modifications are required. Cost performance and comparison with other products, The pricing of the product is great. You receive a product made from quality materials that does away with the original part that can fail causing problems and saves weight and space, just look and compare the two items in the photo attached. About shipping and packaging, My order was shipped within 48 hours of me placing the order and I received a few emails advising me of the status up until the order was dispatched. I find the link supplied to track my order very useful and the order arrived within the estimated date range. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
KITACOSide Stand Switch Canceller
I am switching from an XSR900 to a Majesty S. I was stressed that the engine would cut out if I did not put up the center stand even for a short stop, such as to buy a can of coffee. I had ridden a Cygnus 4, but the Cygnus had an exposed side stand switch, so I had to change the angle of the switch to accommodate it, but the Majestic S had the switch covered by a cover, so I bought this product. I was worried because I had broken my nails many times when removing and installing covers on scooters, but I gathered information from Net, bought a spatula for interior removal, and took the plunge. When going to remove the covers, I used Baki!" The Blue coupler was easy to find, just as Net had said it would be. I am not used to doing this, but the most difficult part was the separation of the coupler. The claw part is on the reverse side and not visible. It was also difficult because the coupler cord was just barely long enough to prevent finger movement. I don't need this coupler anyway, so let's just cut the nail off this one already." I then used small nippers for plastic models and carefully scraped off the nails so as not to cut the cords, and finally managed to separate them. I was able to install it somehow, and I am very satisfied with the result. View detail
Fits: HONDA PCX125, HONDA PCX125Hybrid, HONDA PCX150, HONDA LEAD125, HONDA ADV150, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA CT125CT110 HUNTER CUB
Cheap and Easy Fix for a Broken Side Stand Switch on the Grom
About quality and texture: I am happy with the quality of the side stand switch canceller, the white electrical plug and black wiring are as good as the Honda OEM items. About the feeling of use: When the stand stand switch breaks the replacement Honda part is quite expensive and the safety aspect was not a great concern for me so this cheap and easy fix from Kitaco was a great choice. Products to buy together: Kitaco have some great items specific for the Grom and if you enjoy carrying out your own maintenance then the ECU error check tool would also be desirable to purchase along side the side stand switch canceller. Difficulty of installation: The process to install takes about half an hour, the time is mostly down to the removal and installation of the seat and the left side body panel for access to the electrical boot that contain the green electrical connector for the side stand switch to be disconnected and the switch canceller put in it's place. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting a well designed product that removes the need to replace a broken side stand switch and saves you some money in the process. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: If you are an experienced rider I say the side stand switch canceller is safe to use but if you are new to riding and still learning I'd say to replace the broken side stand switch with the Honda OEM part to be safe. View detail
Might be a blind spot. Useful to have.
SUPER CUB110 (JA44) However, thanks to the conversion to CROSS CUBOEMfootpeg, the Quantity:Pair (for Left and Right) Since there is a Bracket installed on Both Sides, I immediately purchased a relatively inexpensive Right Side Stand for CROSS CUB from KITACO and installed it.
If you use it, it is quite convenient. If you have to park on a slight incline and the right side is down, you may feel uneasy with a normal STAND because of the reverse bank, but with RightSTAND, you can park with a sense of stability and peace of mind.
Or, when parking on the side of the road and taking pictures from the other side of the river, with LeftSTAND, the motorcycle will be flustered, but with RightSTAND, the motorcycle will bow to you, and it will look good. (Is it just me?)
If you don't have it, that's fine, but it's useful to have it, so at this price, it's not a bad idea to have it on.
Incidentally, this Side Stand does not rub even if the RightCorner is banked considerably; the Stand stopper part of the Footpeg hits before the STAND (^^;
View detail
Fits: HONDA PCX125, HONDA PCX125Hybrid, HONDA PCX150, HONDA LEAD125, HONDA ADV150, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA CT125CT110 HUNTER CUB
Type B KITACO Side Stand Switch Cancel
There is nothing much to say about this piece for the monkey. This is going to be used for diagnostic and if there is a kickstand sensor malfunction. This product comes with a MFG. Warning *The use of the side stand with the engine running is dangerous and may lead to loss of motorcycle control and an accident. *Do not start the engine with the side stand in the upright position.There is a risk that the vehicle may jump out or fall over. *When starting off, ensure that the side stand is down before riding. View detail
Easy to use!
I installed it on my APRIO! Very easy to use and convenient for shopping etc.!
It's a bit of a pain because you have to remove the Cowl during installation, but the quality is great and the Instruction Manual is easy to understand!
View detail
Fits: HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle)
It would be very useful!
I installed it on my AF25DIO that I had been driving until recently.
I bought this because I was tired of having to stand and park the Center Stand every time. It is very convenient! The texture is also good.
However, please note that installation is a bit more difficult.
View detail
Fits: HONDA monkey, HONDA monkey, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY BAJA
KITACO
As required for the installation of Rear Sets
After wondering which Manufacturer to choose, I decided to go with KITACO! So I bought it. The product is well made and painted as I had imagined, and the installation was completed without any problem. However, it was necessary to modify the gap between the STAND and the mounting point, which may vary depending on the STAND manufacturer, but it works fine.
View detail
Reliable Brand
In the review, it was mentioned that the Spring was hard and difficult to install, but I was able to install it easily.
The quality of the product is good and satisfactory.
View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
Installation of N-MAX Side Stand Switch Canceller
My friend's Yamaha N-MAX is not able to run the engine without the side stand, which is inconvenient.
You are responsible for any problems that may occur since you are removing a function that is attached for safety reasons.
For safety reasons, I would not recommend it, but my friend seemed to be satisfied with Large.
The work itself is easy, as it is only a matter of replacing the Cover if it can be removed.
I think someone with a SuKill can make it on their own.
Well, since it is inexpensive, at 330 yen, you can't go wrong with buying it.
View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
Easy
It will be possible to start the Engine with the Side Stand out.
It would be strange if you short-circuit it yourself, but this product is easy to use because all you have to do is to attach it.
It can be easily installed by simply short-circuiting the side stands switch.
View detail
I should have put it on sooner.
This is the 15th year I've owned a ZOOMER and installed it.
I installed it for convenience, but I also installed it for coolness.
Installation itself is very easy. However, the diameter of the bolt is a little large, so I had to use a monkey wrench to tighten it.
It is sturdy and will last for 10 years.
View detail
Fits: HONDA PCX125, HONDA PCX125Hybrid, HONDA PCX150, HONDA LEAD125, HONDA ADV150, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA CT125CT110 HUNTER CUB
Side Stand Switch Bypass
About quality and texture - Excellent quality, OEM like product. About the feeling of use - Works as advertised, side stand switch is now removed from the circuit. Products to buy together - Add a Kitaco sticker to your order to add a little something to the Monkey sidecover, numerous sizes and styles available here on Webike. Difficulty of installation - Easy installation, removed the left sidecover and locate the side stand connector in the bundle pictured. Cost performance and comparison with other products - Cheap way to bypass a damaged side stand switch which are quite expensive, no other brands selling this product that I can see. About shipping and packaging - Packaged perfectly and all items arrived safety. This sea freight combined order was very well priced. Any concerns, cautions, or advice when purchasing - If you want to retain the safety aspect of the side stand switch then do not by this product. View detail
Fits: HONDA monkey, HONDA monkey, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY BAJA
Note that R is thick.
I had to return it because the R near the Bolt hole for the STAND was not smooth, but was cut roughly and interfered with the STAND, so the Bolt could not go through.
Maybe if it's not defective, it should install easily and without problems.
Compared to the Side Stand Bracket from another company, it looks like the R part around the bolt that goes through the STAND is thicker, so if you have a machine like a Grinder that can grind it off, you'll be safe.
View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
It's cheap, thank goodness.
I used it for MAJESTYS.
If you remove the SIDEUnder Cowl a little, you can install it, or you can keep it on STAND.
It's nice to be able to warm up.
You can make your own, but for this price, I'd buy it.
View detail