Reviews
Quality is poor for the price.
It is a reasonable price, but I don't think the quality is good. There were welding spatters all over, BALI all over the part where the Bolt is inserted, and even scraps from cutting the Screw. View detail
Fits: HONDA CB1100, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA X-4
K-Factory rear shock slider
Ok so I was expecting the slider to be bigger than it was so not sure it will offer much protection,I can say that the product is well made and looks nice when fitted View detail
countermeasure against standing up
Coloring also matched Cafe in Black??Gold.
We won't know the effect until we take it down, but installing it as an insurance policy gave us great peace of mind.
View detail
Fits: YAMAHA R1M, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA MT-10, YAMAHA MT-10 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA YZF-R6
It was expensive to prevent Rust.
I have attached a Stand Hook even though I do not have a Maintenance Stand. The purpose is to prevent bolt hole rust.
I ordered at Tension at night even though I'm not particular about K-FACTORY, and when I reconsidered, it had already shipped and I was done with it.
If you want to prevent Rust, you can use a cheap one.
As mentioned above, I don't have a maintenance stand, so I don't know how I feel about it, and I don't have any feelings for K-FACTORY as dress-up parts.
View detail
Fits: SUZUKI DL1000 V-STROM650, BMW S1000RR, BMW S1000RR, KAWASAKI Z1000, KAWASAKI ZX-10R, KAWASAKI ZX-25R, KAWASAKI ZX-6R, SUZUKI GSR750, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R750, SUZUKI GSX-S1000F, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX250R, SUZUKI SV650, SUZUKI KATANA, SUZUKI GSX-S1000, KAWASAKI NINJA250
Easy and clean!
It's easy, beautiful, and a dress-up! View detail
Easy to handle, looks so-so.
Easy to install and looks ok. View detail
_TS.jpg)
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ900R, KAWASAKI ZRX1200 DAEG, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
for safety lift
The surface is very clean, and the installation is very easy. Fasten the enclosed bolt to the swing arm. The surface is smooth and beautifully finished It looks strong enough. The lift requires a spool-shaped hook receiver. Please refer to the picture Also, if you apply rock tight when you do bolting I think we can prevent loss in advance. View detail
worst case scenario
Please be careful with this shoddy product. The paint peeled off when I opened the package. View detail
Risk Reduction
[How is it used?
In case of emergency.
Was the installation difficult?
Remove the NORMAL AxleBolt→attach the included AxleBolt (with a hole for the shaft)→Slideretc. and attach the rest of the parts. If you have a Glasses Wrench and a Hexagonal Wrench, all you need to do is to follow the instruction manual. It took me about 10 minutes to do it.
How was your experience with it?
If you look closely, there is a small gap between the brake side bolt and the gold base plate, which is not a good parenthesis.
But overall, I am satisfied with the Dress-up and everything else.
I'm glad I put it on." I hope that the day will never come when we will be able to do so.
View detail
Installed on SEROW250
Since DAYTONA's EngineSIDEGuard was already installed on SEROW, a simple Under Guard was installed.
Installed with 4 Screws.
It is Simple, but when it is running, it makes a clunking sound, so it seems to be Guarding the Engine.
View detail
Fits: HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA X-4
k-factory stuff was always good
The left and right sliders are very light and neatly injected. It's simple to install it by putting it in the left and right holes of the front axle. I have z900rs, but I changed the front suspension to raise up light I bought it for cb1300sb and installed it. The middle gold metal ring has a very good design. View detail
No worries in case you fall down!
[How is it used?
I purchased this car so that I can drive it safely even if I fall down when I go on a long trip, such as touring destinations.
Was the one you received as per Image?
Quality is as good as the Image.
The precision of the screws and pipe lengths, etc., were fine.
Was the installation difficult?
It was a complete Bolt On.
I was concerned about the durability of the Axle ShaftBolt since it is a hole type, but when I saw the product, I was reassured that it was well made.
How was your experience with it?
I have not fallen down yet, but it also has a dress-up effect.
[Included Parts:were they on?
Instruction Manual, Bolt, Shaftetc.
[Was there anything that disappointed you?
I am concerned about the durability as it is anodized and may fade in the future due to sunburn, etc.
For Honda models other than CB1100, CB400SF, CB1300, etc.Fork pitch is the same type and can be used with Hollow Axle Shaft by Bolt On. In my case, I use it with 0 pointsShaft and it works fine.
View detail
Focus on appearance
I almost never scrape here when I fall (experienced,, sweat),
Well, I introduced it because I thought it was important to look good.
One point of Gold is nice.
It is also well made.
It comes with a detailed instruction manual and is very easy to install.
View detail
light
I used to use Stainless's Other Brand Product, which was the same 30mm long, but it was refracted and lacked the actual length.
This product is lighter and straighter than that, 30mmLong, so I could get the length I wanted.
View detail
I'm a little nervous.
Installation is easy, just swap them in and out. However, it feels shorter than expected, and the STAND-UP is a bit scary.
I guess I'll get used to it.
View detail
Emphasis on decoration
It was the first product that came out, so I installed it, but it is a little expensive. I was glad that there were no decorative elements in this part, such as the decorative plate on the base or the aluminum collar, which is not visible after installation.
Quantity:Pair (for Left and Right) Note that two sockets of the same size are required because they will be supplied if they are not held from the
I don't know how effective it is because I haven't tipped it over. (I feel that if the bottom case is tipped over in such a way that it is damaged, it would not be enough to protect Axle.)
I think it would be easier to attach and detach if one side is fixed, but I don't know why.:Pair (for Left and Right) It is a hassle because you have to hold it down from the
View detail
Satisfied
This is what you get when you Lowdown.
I like the casual Mark!
View detail
Nice fit.
Slider fitment can make the front lower part look more solid and fuller. insurance that will protect against unexpected damage. View detail
I think it's the Front Axle Slider from Best Buy.
Someone has already written a Review, so here is another perspective.
Front forkBottom and Brake Caliper are not affordable to replace with Wound.
But when I tried to buy a Slider for that purpose, it cost me 15,000 yen for two small chunks of DURACON and a mere stick of All Screw in a Vinyl bag. I was like, "Are you going to pay 15,000 yen out of the small amount of money you have in your pocket? It was an Image like that.
The quality of each part is so high that it can withstand the act of looking at it next to the PC until the day of installation after it arrives.
The shaft is not just an all screw, but a machined aluminum alloy shaft, so I did not use the included stainless steel screw, but prepared a separate Duralumin screw to assemble the shaft.
This is a great QUALITY product as others have stated in their Reviews.
Before purchasing the product, I was a little concerned about the Logo, which is often noticeable in photos, but in reality, it is a small one, so it is not particularly noticeable.
Anyway, we strongly recommend this product to those who are not sure which front fork slider to choose.
View detail
Smaller Accent
The small accents and gold on the feet are very effective. I hope this Parts will never be active …. View detail