Reviews
Purchased for appearance.
Purchased for appearance.
It is not a cheap overseas product, but a reliable AGRAS, so it is a beautiful AnodizedBlue. The quality is very good! I think the price is a bit high. I would be satisfied with Large if it were a little cheaper.
I have it on a different Motorcycle as a decoration, but it has never tipped over, so I don't know how effective it is. But I think it is better to think of it as a decoration.
View detail
You can put it on yourself.
It was easy to install, although the bolt needed to be temporarily fixed. View detail
Be careful when installing!
The product is Large and satisfactory, but the Bolt On seems to be easy to use. However, when removing the OEMBolt, I had to be very careful to support the Engine with a Jack and remove the Bolt, but the Frame and Engine still gapped a little.
The center of the bolt is gapped.
In the end, I took it to the Shop and asked for it. 。
SliderManufacturer or not, we think it is better to leave it to the Shop, as we think it is very difficult to install.
View detail
O-ring is Garbage
I thought I read that TENERE fit up to 23, but I bought it.
No problems with installation, no interference with brake pedal etc.
There is no particular change in operability, but it seems to be easier to apply the ankle area to the vehicle body.
The other thing I would like to see is the appearance and the ability to put a lid on the Pivot shaft mounting.
There is nothing wrong with the accuracy of the product itself, but the weatherproofing of the O-ring that comes with it is very weak! I don't think it will last more than 2 months.
It is possible to substitute the O-ring fixing part with Tie Wrap. However, I would not use this material because it does not look good.:I have replaced it with a SiliconO-ring and am using it. So far there has been no deterioration.
View detail
To insure against standing over.
It was a little odd that the cowl had to be removed, so it was a little large, but I was able to install it. I don't know the Torque for tightening, so it would have been helpful if it was written in the Instruction Manual. View detail
Is it a stock take-up Large sturdy?
Dec. 23, 2011 There is information that the Right Side does not match the screw Pitch.
The stock items are probably from that lot as well.
The person who purchased the same lot said that the holes are off by about 2 cm when temporarily assembled.
Manufacturer has informed us that it is not a glitch.
Hard to imagine, but perhaps 300 is different from 250?
View detail
Well, yeah.
I don't like that the Bolt on the Front side can have a little gap.
It is recommended that two Jacks be used so that the Engine does not Gap.
I don't like the point where the Bolt paint peels off with Wrench when tightening.
View detail
Bonsai Moto
Installation is not difficult, though,
It's like pushing in the Cowl on both SIDES.
When I go to tighten the Bolt, it says "mi-Stainshi".
For bonsai purposes who do not want to damage the Cowl.
Another Brand may be better.
Since the defense seems to be high
I recommend it to anyone who wants to come home safely.
View detail
Convenient for length adjustment
When tightening the Screw
It would have to be a narrow Socket to fit.
I fixed it with Locktite243.
It has loosened under the weight of the car.
I fixed it with Locktite263 and it stopped working.
Maybe you can't take it off now. w
View detail
Installation could not be done
The FTR223 could not be installed because the fixing part of the Chain Cover was changed in the middle of the process, but it could not be helped because of my lack of confirmation. The quality of the product is good and I think it would have been a good product if it had been installed. View detail
Short Stand
Short Stand is safe because the car body will stand up when Lowdown. View detail
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
Fits: APRILIA RS125, DUCATI MONSTER S2821, DUCATI Panigale 899., APRILIA RSV1000 Series, APRILIA RS250, YAMAHA , TRIUMPH DAYTONA675, APRILIA SL750
I went with Gold...
I bought it to go with the rear stand, but I think it would be fine with other Manufactures.
The color jumps with age when exposed to the sun, I think the same for the others.
If so, I'm glad it was inexpensive.
View detail
Fits: HONDA CB1300ST, HONDA CB1300SB-SP, HONDA CB1300SF, HONDA CB1300SB, HONDA CB1300SF-SP
Purchased for protection in the event of a fall
I bought it in case of emergency.
However, the product I received was scratched and the plating was peeling, so I contacted the manufacturer directly to have it replaced.
I ended up removing it because I was worried that I would not be able to remove the Crankcase Bolt in the event of a fall.
View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI Ninja ZX-6R 40th, KAWASAKI Ninja ZX-6R KRT EDITION, KAWASAKI Ninja ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R
I'm just making a connection for now.
I purchased this product because the G-type Slider is not available.
The large size is sturdy even without removing the cowl.
It stuck out quite a bit, but I thought the Bracket at the mounting point could damage the Crankcase if impacted.
For now, it's just a connection until other Manufacturers are available.
View detail
Perfect appearance
I'm not mocking it up,
Effectiveness is unknown,
It is better to think of it as a dress-up,
And to think,
I think the price is high.
View detail
Better than nothing, installation hassle
The Female Screw side did not fit as expected, and I measured it with Caliper. 0.5 millimeter. I managed to insert it by shaving the average thickness with Belt Thunder.
Personally, I think Other Brand Product is the way to go!
View detail
Fits: TRIUMPH DAYTONA675, KAWASAKI NINJA400, SUZUKI , KAWASAKI ZX6R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z400, KAWASAKI Z250, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, KAWASAKI ninja, DUCATI Late 999, HONDA , DUCATI 749, BMW S1000R, BMW S1000RR
good
Since it is the same Manufacturer as STAND.
Because it is not as flashy as other Manufacturers.
View detail
Fits: HUSQVARNA TE250, HUSQVARNA TE300, GASGAS EC250, GASGAS EC300
No instruction manual ??
There is no instruction manual... I just kind of put it on as it was supposed to be put on, but I have thought about the under plate, but why? I have a Clip nut, but I'm not sure if it is used in the right place.
At any rate, it looks like it's going well, so I'll enjoy it!
View detail