Reviews
Wow, that's expensive!
The product is great, but not quintessentially expensive. View detail
![[NISSIN Repair Parts for Master Cylinder] Mirror Holder](https://img.webike-cdn.net/catalogue/daypic140709/36206_1_l_TS.jpg)
Mount expansion foundation with no gap required
[How is it used?
Used on the Clutch Side of CBR250RR (MC51) from April 11, 2020 to October 2, 2023.
Mount the iPhone miniSeries using the following parts
1．RAM MOUNTS BallMount M10xP1.25：https://www.webike.net/sd/24021956/
2．RAM MOUNTS Short arm：https://www.webike.net/sd/21313052/
3．RAM MOUNTS XGrip (M) Smartphone Holder (maybe):https://www.webike.net/sd/22558592/
4.Large amount of Screw Lock agent
Was the one you received as per Image?
The product is exactly as shown in the image.
Was the installation difficult?
I forgot to measure the distance between Bolt.
BoltQuantity:I guess it's easy enough to remove and replace the 2pcs and install. Since I feel there is a gap at the bottom, it may need to be filled with Washer or something.
How was your experience with it?
The Smartphone Mount is a good choice because it requires far fewer unnecessary parts than a dedicated bar.
Since it is installed by replacing the original parts, there is no need to consider the gap between handlebars, etc., unlike retrofit Mirror Holderet etc. The original bolt can also be used.
Smartphone mounting is possible with far fewer wasted parts than with dedicated mount bars, etc.
After mounting the ball on the car body, I shook it with the ball, and the car body shook, so it seems to be robust.
I don't remember how many times I actually ran with my phone on it.
Riding the phone on the Clutch (Left) side rather than on the Brake (Right) side met the request because I prefer the LeftMount for the possibility that the phone could escape to a non-roadway in case of an emergency.
[Included Parts:were they on?
Included Parts:None, only this product wrapped in Vinyl
[Was there anything that disappointed you?
I think I used a similar part from YAMAHA for the R6 Brake because of the similarity.
YAMAHA 5YU-26393-00：https://www.webike.net/sd/25729937/
That one did not occur when the gap was R6.
[Notes]
This product Mirror Holder It is used like the CF POSH Universal mirror holder (https://www.webike.net/sd/1125900/), but it does not say anywhere that it is for smartphone mount.
View detail
![[Repair/Option Parts] HC1 Mirror Clamp](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0312/24242681_20220922155532363_TS.jpg)
Unplug and replace Pin.
Remove and replace the Clamp Pin that is attached from the beginning.
It is Slim with a Fit feel because it is OEM, rather than the Mirror Clamp which is a retrofit. The color is painted the same as the Body color, so it feels very high quality.
If you do not have a pin, you need to prepare a hammer and a punch because you will need a punch when you pull out the pin.
It is Magura OEM, but I believe it can be installed on Motomaster as well.
View detail
Using Universal
I used it to install the Steering Damper.
No Recommendation.
View detail
Things are good!
Things are good.
It's normal, tightly Cut-out&Black processed, and it's working well!
But it's still expensive.
View detail
Material is solid.
Required if you want to install the Mirror on the brembo Master CylinderClamp.
The price of the clamp alone is very high, so I'm looking at other brand products, but if you're looking for materials and precision, the brembo OEM is definitely the way to go.
There are products like Posh and Craftman in Aluminum cutting, but it doesn't matter anymore if the color doesn't match up with MASTER or not, the Material and treatment used is clearly different.
If you're going to use the brembo MASTER, I felt it would be a shame to lose some of the rigidity in this area.
View detail
It looks good. But I'm a little tired of the bullish pricing.
Handle mirror & Handlebar area is unified to brembo.
Changes.
Mirror:Cowl mirror ⇒ Handle mirroring
Replacement/Additional parts.
Using Z800Handle mirror
・brembo MirrorHandlebar clamp
・SUSSpacer D14.0mm, t2.0mm
The Ninja1000SXCowl mirror is transformed into a Z800 OEMHandle mirror for a cleaner look.
The Mirror on the market is excellent in terms of design, but it is undeniable that the mirror surface may shake at high speed driving. Since there are concerns about the strength of the product, the OEM product with a proven track record of reliability is the one to choose.
In the case of OEM products, the basic M10 handle mirror is still able to be installed.
In order to avoid the blurring of the mirror surface, the Handle mirror of the aerodynamic type is chosen, and although it will be chosen from the Mirror of Z series, it became Z800 by a process of elimination to avoid the interference with the Wind Screen and to be compact in the direction of the width of the car.
The price is also very reasonable for 1pc, probably because it is made in Thailand.. It was the cheapest at about $5,000.
The installation should only install Mirror after clamping to Handlebar, but it does not seem to be attached as it is.
Because the length of the screws is too short for the brembo, it will hit the upper bolt which clamps when you try to tighten it to the end.
It's hard to get a spacer for M10 because the size of about 14mm OD doesn't exist in general. I managed to find an existing product and bought 2 types of t2.0mm and t3.0mm by insurance.
The result was Large sturdy at t2.0mm.
I bought it on the spur of the moment when it was on Sale, but I think brembo's Holder is too expensive for Quality (lol).
View detail
I changed the screw thread and replaced it.
Every time I go to the forest road at SEROW, I removed Mirror, the threads got damaged and I replaced it. The price was also cheap and easy to install! It was thin and so it was possible to install around a relatively narrow Handlebar! View detail
Without mounting Mirror
I just found a good one to unify Silver around Handlebar.
It was perfect as it does not take Space.
I was also solidly making
View detail
![[NISSIN Repair Parts For Master Cylinder] Mirror Holder](https://global.webike-cdn.net/photo/article/44/1366812881844L.jpg)
[WeBike Monitor] It Bound tight too much and has been divided into two. Special attention is required to a Torque. Since it was its carelessness this time, it is unavoidable. It was not bad at all in product, and carried out. It is a Recommen
[WeBike Monitor] It
Bound tight too much and has been divided into two.
Special attention is required to a Torque.
Since it was its carelessness this time, it is unavoidable.
It was not bad at all in
product, and carried out.
It is a Recommendation at the Accent of the circumference of the
Handle.
View detail
![[NISSIN Repair Parts For Master Cylinder] Mirror Holder](https://global.webike-cdn.net/photo/article/02/1366203063502L.jpg)
It purchased in order to Handle-mirror-ize Ninja1000! Since 1152 was touch as the slightly high kana ? now although the direction besides was written, but there is also no substitute in others and he bought it with bulk purchase 1129 as at a low pric
It purchased in order to Handle-mirror-ize Ninja1000! Since 1152 was touch as the slightly high kana ? now although the direction besides
was written, but there is also no substitute in others and he bought it with bulk purchase 1129 as at a low price as possible, it is the good kana!?
View detail
Since the Bar handle was used, it purchased. To Mirror attachment, it is satisfactory.
Since the Bar handle was used, it purchased. To Mirror attachment, it is satisfactory. View detail
![[NISSIN Repair Parts For Master Cylinder] Mirror Holder](https://img.webike-cdn.net/catalogue/daypic140709/23255_1_l_TS.jpg)
A combination with Nisshin different body master. As it is a genuine Nisshin, it is a just fit and a color sutis. If the screw location of a mirror is on a front side and high lposition, the balance on both sides is difficult. If there is a room at the le
A combination with Nisshin different body master. As it is a genuine Nisshin, it is a just fit and a color sutis. If the screw location of a mirror is on a front side and high lposition, the balance on both sides is difficult. If there is a room at the lengh of a handle bar, it may be ok to use the mirror holder. View detail
Since an authentic positive one was damaged, kawasaki D-tracker of 03 models was equipped. It can equip easily [ the space of the handle limited by the slim body ]. Although uneasiness is in pure thinner part reinforcement, the lineup also of the
Since an authentic positive one was damaged, kawasaki D-tracker of 03 models was equipped.
It can equip easily [ the space of the handle limited by the slim body ].
Although uneasiness is in pure thinner part reinforcement, the lineup also of the some colors color is carried out, and it is also possible to push forward admiration custom.
If reinforcement is also proved now, it will be *x5 rightly.
View detail
Since he wanted to mount an external meter to a handlebar, this holder was used. Since it adjusted to its the favorite angle and place, it was able to attach to the place where a meter is the most legible. I think that there are various uses accor
Since he wanted to mount an external meter to a handlebar, this holder was used.
Since it adjusted to its the favorite angle and place, it was able to attach to the place where a meter is the most legible.
I think that there are various uses according to a device besides a mirror.
View detail