Reviews
Neat appearance. Prevents rust caused by raindrops.
Removed the cowl mirror from CB400SB and replaced it with a handle mirror. At that time, I replaced it with TANA-X Shark5. I couldn't bear the uncomfortable feeling like a snail when I rode SUPER BOLDOR for the first time, so I spent a large amount of money to replace it with my favorite mirror.
However, because of the cowl, I could not easily install it, so I even bought a Tanax Adapter or something like that, and finally got it to fit nicely. Finally, I was able to fit this cap.
The product is good, of course, but I think it is a little expensive if it is stolen or falls off due to vibration. If it were a little cheaper, I would like to cover various places properly.
Please give us a discount. Also, please give us the smallest size.
View detail
Thanax M10 mirror bolt cap
Quality and Texture Information The feel of the plastic product is clean. Products purchased together TANAX: Off-set Holder 45 is easy to install.
If you install it alone, you will be able to prevent problems that occur due to the bolt fixing part being exposed at the top.
Webike delivery and packaging are in excellent condition. Thank you. -------------------------------------------------- -------- Quality and Texture Information The feel of the plastic product is clean. Products purchased together TANAX: Off-set Holder 45 is easy to install. If you install it alone, you will be able to prevent problems that occur due to the bolt fixing part being exposed at the top. Webike delivery and packaging are in excellent condition. Thank you. Powered by Google Translator
View detail
TANAX M10 Mirror Bolt Caps
125 years old, 125 years old, 125 years old.
I want to know more about this.
I bought the genuine Monkey 125 side mirror because I couldn't see the rear clearly.
After installing the offset holder, the mirror viewing angle will be good, allowing you to see what's behind you and drive safely. -------------------------------------------------- -------- The side mirror of the genuine Monkey 125 was purchased because it could not show the rear. After installing the offset holder, the mirror viewing angle is good, so you can show the rear so you can drive safely Powered by Google Translator
View detail
arrangement
Quality and Texture Information Plastic Products It's neat to look at the feeling of use Products to purchase together TANAX: Off-set Holder 30 [SA-23] It's easy to install Cost performance and comparison to other products TANAX M10 Mirror Bolt WeBike packaging is always great, arriving in a week for delivery and packaging Concerns about purchase TANAX: If you purchase Off-set Holder, you can neatly organize the purchase together View detail
Fits: HONDA Rebel 1100, HONDA Rebel1100 DCT, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR
daytona mirror bolt
The packaging from WeBike was very thorough. The mirror bolt is much lighter than expected and the build quality is excellent. I purchased the titanium color and installed it on the CB400SB. It fits well like a genuine product. I intend to purchase again next time and recommend the purchase. -------------------------------------------------- -------- The packaging is very meticulous in the Wybike. The mirror bolt is very lighter and more built than you think. I bought a titanium color and was mounted on the CB400SB. It looks like a genuine product. Next time, I am willing to buy and recommend purchases. Powered by Google Translator View detail
Good product with good design
I installed it on a 2014 s1000rr.
I bought it to use as a bar end mirror, but it is simple and blends in naturally with the design.
Installation is easy, just tighten 4 screws.
The quality is reasonable and I am satisfied with the product itself.
View detail
OEM Parts Flavor
[How is it used?
In conjunction with the conversion of the Mirror on the 390DUKE to an Other Brand Product, we decided to use the Tanax Off-set Holder 45 (product number:SA-25) to improve the Mirror's visibility, I installed this product to prevent water from collecting in the hexagonal holes of the bolt and rusting.
Was the one you received as per Image?
Material:It is a Plastic Cap. If you handle it roughly, it looks like it will be damaged soon.
Was the installation difficult?
There are no claws attached to prevent it from falling off, but it is a little tight-fitting so that it will not come off immediately. I tried to remove it once as a test, but it was quite difficult, so I don't think it will come off without permission while driving.
How was your experience with it?
I am satisfied with the finish as if it were OEM Parts.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Point or hang for installation:If the cap is pushed in at an angle, it will break. if the inside of the hexagonal hole is already rusted, it is better to remove the rust first before installation.
Instruction Manual:There is no Instruction Manual, but as you can see, it is a simple structure, so you just need to push it gently into the hexagonal hole of Bolt.
View detail
Retro Style.
Ideal for creating a Retro Style. It also helps to hide Mirror's fixed Nut, which is rusting from scratches caused by tools. View detail
![Mirror Block Off [Mirror Blanking Plates]](https://img.webike-cdn.net/catalogue/images/50737/22772302_1_TS.jpg)
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR1000RR
R&G Mirror Blanks for Honda CBR1000RR 2016
Let's be honest, no one really likes the stock mirrors that come on most manufacturers these days, and for this reason a set of mirror blanking plates were purchased for the 2016 Honda CBR1000RR. This part was found using the reference on R&G website, this set does fit a few models of the CBR and Webike stocked them no problem. With some other parts shipped by EMS and arrived in 5 days. All arrived in perfect condition. The blanking plates are really cool, they have a nice R&G logo and are made from what looks like an aluminium metal. The finish on them is superb, the paint looks smooth and no sign of any flaws that I can see. The printed logo is crisp and clean. Comes with their own blots so no need to worry about losing the ones from the stock mirrors. Fitted really well and look pretty awesome. I already have some small bar end mirrors installed so can still see what is coming from behind. Overall, very pleased with the purchase. Keep it up Webike, thanks. View detail
Fits: HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA Rebel1100, HONDA Rebel1100 DCT
Not a Mirror hole, but...
The Z900RS has a base on the Frame for use with the Option Center Stand.
If the Center Stand is not attached, the Screw holes are visible and we would like to fill them for protection.
The hole size is M10×1.25, so you can use a hole-filling bolt for Mirror.
Lightweight Material:The trapezoidal bolt is made of aluminum and has a simple design, but is cool.
The Right Side simply attaches to the Screw hole.
The Left Side does not have Screw holes, but this time ButylTape was used.
Wrap the ButylTape around the bottom of the bolt and the neck in an O-ring shape and push it firmly into place.
In fact, the YOSHIMURA frame plug we are using now was originally installed with an O-ring, but it didn't feel quite right, so we removed the O-ring and pushed it in with a ButylTape. It is very firmly attached.
ButylTape is originally designed for waterproofing of lamps and mating surfaces, but it can be used for a variety of purposes if you have one pc.
View detail
I changed it at One point.
I changed it at One point and became Accent and I like it. View detail
This is a must for off-road mirrors!
I bought this for the root dress-up when I replaced the Mirror on my CRF250RLY50 with a DRC161 off-road mirror.
This product is sure to increase the overall Off-road feel.
However, when using CRF250's 161 off-road mirror, it is necessary to pull the mirror up as far as possible while expanding the upper part because the mirror's foot part is too short to tighten the fixing bolt if it is installed as it is.
New Material:Since it is a Rubber product, it can be spread out quite well, but it is considered that sufficient care should be taken to avoid the possibility of it being cut if it is spread out too wide.
View detail
Fits: DUCATI PANIGALE 1199 R, DUCATI PANIGALE 959, DUCATI PANIGALE 1299 R FINAL EDITION, DUCATI PANIGALE 1299, DUCATI PANIGALE 1299 S, DUCATI SUPERLEGGERA 1299, DUCATI PANIGALE 959, DUCATI PANIGALE 1299 R FINAL EDITION, DUCATI PANIGALE 1299, DUCATI PANIGALE 1299 S, DUCATI SUPERLEGGERA 1299
Mirror-less
Installed in conjunction with Mirror-less.
The appearance has been Refreshing.
View detail
Genuine Lightech Mirror Blanks for R1M
These were a needed part for an R1M 2020 model after removing the OEM mirrors and replacing with aftermarket ones. This was a preference for a customer of mine who did not like the stock ones on their bike when they purchased it. The correct part number was found simply by visiting Lightech's website and searching for the manufacturer, model and year. Super easy. For how much the difference is between Webike and my UK stockist, it was a no brainer. I think Webike are stocking a lot of the brands that people actually want, especially Lightech. I always have other items in my basket and adding these to the order made the cost of shipping that little bit more bareable. I used EMS fast service which virtually guarantees delivery within a week every time I have used it. This was no exception and everything arrived in 5 days. Webike are one of only a couple of my go to companies for motorcycle parts that take a good amount of care in packaging the orders you place. Even though there were some strange and light parts in my order along with some heavier ones, they packed out the box with additional packing to stop much movement in transit, a simple thing but as I said, not many do this. They also seal the outer box so nothing can get in or out during transit. All arrived in perfect condition and even some of the gaskets which you kind of expect to take a hit, was 100% perfect. These mirror blanks are a really nice addition to a bike of this year, on a 2020 bike you do not want something that looks tacky and cheap. The CNC machining is spotless and the anodising is perfect with no light or dark spots. All extremely well done, the curves are gorgeous, the lines are super clean and along witht he stainless fittings they look absolutely stunning. Generally, I do not care much for OEM mirrors myself, not really sure why a lot of manufacturers don't design better ones but hey. Fitted really easily but take your time. The end result is fantastic. Thank you Webike for the great services you provide. View detail
Fits: HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA Rebel1100, HONDA Rebel1100 DCT
Bar end mirror accompaniment
Bar end mirrors were installed to cover the screw holes.
It is just a Screw, so there is nothing special about it, but I chose this one because it has a different shape from the other ones, while most of them have a Minus shape.
View detail
nice little accessory
My YAMAHA XMAX300 has refitted the front rearview mirror. The original screw hole needs a cap. I searched for a long time and finally let me see it. There is no difficulty in the installation process. Just unscrew the original mirror screw. Direct installation, I prefer the black appearance, low-key and chic, it matches the car very well, and its material will not rust, which makes me very satisfied ------------ -------------------------------------------- My Yamaha XMAX300 modified the front -view mirror. The original screw hole needs to install a hat. I found it for a long time and finally let me see it. There is no difficulty during the installation process. Installed directly, I prefer the black appearance, low -key and uniquely matched the car, and its material will not rust, which makes me very satisfied Powered by Google Translator View detail
I think black looks better
I have been looking for it for a long time and finally let me see it. There is no difficulty in the installation process. Just unscrew the original mirror screws and install it directly. I prefer the black appearance. It is low-key and chic and matches the car very well. Moreover, its material It will not rust, which makes me very satisfied, and I may never find a better product than it. -------------------------------------------------- -------- After looking for it for a long time, I finally saw it. There was no difficulty during the installation process. As long as the original mirror screw was unscrewed, I could install it directly. black appearance. It won't rust, which makes me very satisfied. I may no longer find a product that is better than it. Powered by Google Translator View detail
CircuitSpec.
Used to hide the hole after Mirror was removed during Circuit run.
The Cover itself is thin, but it is sufficient to cover the hole.
View detail
Puch Mirror Cap
I bought this to remove Mirror on Circuit. The texture MATCHED the car body and the look was REFRESHING. The price was reasonable, so it was good. Installation was easy as I only need to fix it with Screws and Fitting was no problem. View detail
Used for Jc92 grom.
Purchased for installation of bar end mirror
I don't have any comment, but it was gold color.
This and a selection of thoughts
Casually, Mr. Mukawa's Laser engraving is a nice Accent.
View detail