Reviews
It is casually MORIWAKI.
I was not happy with the snail-like cowl mirror on my CB400SB, and when I replaced it with a handle mirror, I bought a MORIWAKI one to fill the original hole. At first I ordered a cheap one from Amazon.com, but they didn't have the color I wanted, so I decided to go all out and get MORIWAKI anyway with WebikePoint.
It is a rather nondescript cover with a black matte finish, but since it is a MORIWAKIDesign (I don't know much about it and it is not Mania), I decided to go with it. As I have said many times, it is nothing special, but I think it covers the Mirror Hall in a subtle way.
View detail
When running Circuit.
Purchased to cover up the area where Mirror was removed when driving on Circuit.
Good because it looks Refreshing and Race ish.
Mirror removal is easy as you just use Bolt instead of Mirror.
View detail
It is easy to install. to Racer's look and feel.
Security parts for CBR250RR MC51 for Sports competition (Mirror) I purchased this product for the removal of the
The mirror had been removed and the scratches on it were…not parenthesis looking good, so the purpose was to cover them up.
The effect was perfect and Parenthesis improved.
We have not experienced any problems with price or quality.
Order of installation
Remove the existing Mirror with a .5mm Hex.
Attach this product with a 4mm Hex.
Returning is easy in the reverse order.
It's not tight enough for the Hexagon Bolt to lick.
We feel that Bolt's condition should be closely monitored, assuming that it will be put on and taken off many times.
View detail
CircuitSpec.
Used to hide the hole after Mirror was removed during Circuit run.
The Cover itself is thin, but it is sufficient to cover the hole.
View detail
Mirror hall concealment
When I tried out the bar end mirror, I installed it, and I was a little concerned about the bump with Cowl, but it was acceptable. View detail
Fits: KAWASAKI Ninja400, KAWASAKI NinjaZX-25R, KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR
Mirror Hole Cover
I bought this for a Circuit race. I think I can manage without it, but …… it looks better than leaving it off.
The color is black, and it is plain, but the texture is good, and the casually engraved logo mark is discreet, yet moderately assertive.
I can't use it on public roads, so I'm looking forward to the driving sessions.
View detail
It's neither good nor bad
I bought this because when I removed the Mirror, the place it was attached to was awkward.
There is no problem with the texture.
It also comes with 4 Bolts so you don't have to buy them separately.
I like MORIWAKI, so I am satisfied.
View detail
Fits: KAWASAKI Ninja400, KAWASAKI NinjaZX-25R, KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR
Good texture. Sober but elaborate construction, unobtrusive in a good way.
I've decided to remove the Mirror as I have more opportunities to run on Circuit.
I've been looking for a Can Seraar because my aesthetic sense won't allow me to just remove it.
I've seen other Manufacturers with less than stellar reputations and flashy, expensive products.
intermediate between the two. (?) I decided to go with this one.
As a side note, this is my first MORIWAKI product.
I don't have much luck with KAWASAKI.
The black anodized glossy finish is a great way to hold down the claims of the Parts.
The logo is properly included in the proportion of the three, and it also has some three-dimensional modeling.
It is an elaborate construction and I am personally very satisfied with it.
The reaction makes Bolt's head stand out.
So, I made the Plate about 1mm thicker and the outline about 1mm larger.
If you make the Bolt a plate Bolt and make the Plate surface flat, you get 100 points.
The price seems rather high, but it can't be helped.
It's not like it's going to break, it's not going to sell in quantity, and it's going to cost a lot of money to build ... .
It is much cheaper than One-off production.
View detail