Reviews
Hmmm... subtle color difference.
[How is it used?
I bought this clamp to install on my brembo RCSRadial master. bremboOEM's MirrorHandlebar clamp (part number 110.A263.90) has a list price of 6,160 (tax included) Since the Mirror Adapter costs $3.99, it was stupid to spend a large amount of money on a Mirror Adapter, so I decided to endure with a patrimony (laugh).
Was the one you received as per Image?
The slightly different color is nice and looks like a pachimon! （Nice!)
Was the installation difficult?
Unfortunately, bremboOEM Bolt is not available (crying)
As you can see in the photo, the screw hole on the lower side of the Adapter comes in contact with the Bolt's flange, so the Bolt cannot go all the way into the Adapter. Well, in any case, it is an anti-theft material.:I was going to replace it with a Stainless SteelTorx bolt, though, so that's not a problem. Besides, bremboOEM bolt is just steel.
How was your experience with it?
No problem at all! If you look at it from 2 meters away, you can't tell the difference in color! (LOL)
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Where the colors are subtly different (laughs).
But Cost performance is top notch, so no problem!
Other items that would be helpful
Items to buy together:bremboOEM bolt is just steel, so it is recommended to replace it with a Stainless bolt.
Opinions and requests to Manufacturer:Please make it more like bremboOEM colors and master the path of pachimon! (LOL)
View detail
APE 100
Used for APE 100
TypeDMASTER is positioned in front of the
I bought it for adjustment because the Takekawa Clutch lever is later than the MASTER with Handlebar core.
The height is possible by adjusting the Mirror
Quite a bit of back and forth Quantity:Pair (for Left and Right) It takes a long time to match them evenly, etc., but there is no scope for compromise and self-satisfaction.
Quantity:Pair (for Left and Right) It is good if this price in …
View detail
No problem
The quality of the product was absolutely perfect. View detail
Cancellation, please.
I ordered the wrong one and I need a Cancelation. View detail
A little further out.
I bought this product because I replaced my mirror with a Short mirror and it was hard to see behind me!
Quantity:Pair (for Left and Right) I wanted to put it at a similar angle, but if you look closely, you can see that the mounting position is Quantity.:Pair (for Left and Right) I'm very happy with the way it turned out! I would have been happy if the Bolt that came with it was black, but it's still a Button type, so it's good!
View detail
High quality
It's a very elaborate and beautiful product for the price. View detail
Only the surface finish is disappointing
Purchased in place of the too expensive brembo OEM Mirror Holder
It would be helpful if the colors were displayed more clearly
Personally, I'd rather have all the colors Shot blast applied in advance to give it a cast-iron look I don't think it's strange to match with Master Cylinder, but …
Basically, I think Design is a finish that only fits the slippery shaving MASTER!
View detail
Mirror View Widening to Large
A little more Mirror on the outside would have made it easier to check the rear, but it helps in those situations
Material:The influence on the Handling is small because it is Aluminum and Large and light
You can also choose two different mounting heights for the Mirror, so fine adjustment of its position is also possible
But the Bolt that comes with it is a bit cheesy
A low head Bolt would have looked much better
View detail
Rearward vision is now better
The Z900RSCafe is supposed to be a Short mirror than the regular Z900RS Quantity:Pair (for Left and Right) away
Therefore, rearward checks while driving are not required for Quantity:Pair (for Left and Right) I had to shake my head quite a bit at
When I was getting a reasonable amount of Speed, I couldn't get a glimpse of the eye feed and it was Stress
That's why the old-time flyers used to use short mirrors, and I've been using short mirrors myself mirror
But this time it's too short, so you can see your shoulders in the background needed
At first, I held back on the quackery, but the urge to get the Mirror out three more inches made me buy this one I did
Rearward vision is so much better and the visibility is a perfect balance
At first I thought it would be an inexpensive one
I chose this one by AluminumMachining because it is still a very visible place The quality is high and I am satisfied with it
However, this product is more expensive than MirrorBody, so the quantity:Pair (for Left and Right) It would be great if you could make it about $3,000 in
It's important to note that the Body is highly textured, so
Bolt is also included in Included Parts:I wanted to use the Bolt for something more substantial It was a bit of a struggle, but
What I found out at the time of the temporary clamping is that the Bolt for Mirror is a normal way to get Pitch It's not like Bolt's Pitch
The Bolt that I bought cannot use the Bolt that I bought with great effort, and it became a Waste use After all, I used the included Bolt
View detail
Goods are good !! But it is expensive
Quantity : Pair (for Left and Right) I bought minutes and it costs 4000 yen! I think that the cost is hundreds of yen.
The product itself is very good. I really regret that being high! I wanted POSH to work harder and cheaper
View detail
Cost performance is good.
It was the cheapest one I found, but there was not any problem with the installation.
There is a gap on the lower side, but even if it is too tight, it will not be possible to tighten it,
It is this.
I used Adapter for Mirror so far, but the tightening to Handlebar is sweet,
As Mirror collapsed at high speed, it was not good.
This reduced the number of parts to Handlebar by one and it became clear.
View detail
Excuse me
It is an ordinary item. Material of hundreds of yen : Stainless Steel is not much substitute compared to other Manufacturer. Because it is a product of hundreds of yen. View detail
It's 3 centimeters long and 3 centimeters away
I only saw my arm until now, so I was thinking of Offset. Since it can move only about 3 cm with the Adapter attached, it was uneasy how effective it is until installation. I can see the backward firmly except for. Because it is expensive Parts, it was good not to fail.
View detail
I should have done it from the beginning
Neck was expensive everyone's impre street.
It's higher than popular Mirror selling here.
I purchased an inexpensive competitor OffsetHolder, but I can not move to the position I expected but another Size is already Quantity : I purchased 1 Set.
As a result, it is short and long in the belt...
I was able to install Mirror at the position that I thought to buy just one item of this product by any means.
A total of 4 items of wasteful company.
This Quantity : 2pc. It has become price equivalent to Set.
I feel that Design is also better to this person.
After all, the product to change Position is useless unless you have the adjustment function.
View detail
POSH Mirror Adapter
OEMMirror of MONSTER S2 is fixed with M8 Bolt. Since M10 has more choices than M8, I exchanged the parts clamping Brake and Clutch Master cylinders with for M10.
The color of Handlebar also matched and it felt tightened.
View detail
Although it is a slight Offset
I do not like the position of RightMirror of KTM EnduroR, I want to improve the visibility of the backwards.
Although it is only a small movement, in the case of my Motorcycle, the backward visibility has improved very much.
(Depending on the vehicle. I think there is LargeSmall for interference and improvement with the car body)
It is a long hole, but it can be firmly fixed.
It feels a bit expensive, but it's Cut-out so there's no choice.
View detail
The quality is good - - -
Although it is sometimes called Posh made, it is not bad about the quality aspect, but because Screw 's adjustment range of the car body side has been made wider, the Screw will loosen only by fixing the Screw head alone.
I think that it is necessary to bite Rubber Bush as a countermeasure and make it harder to slip.
View detail
I bought it for a slightly different purpose
I bought Handguard with Bracket I bought at Home center, but because the center of Hand guard and center of Handlebar do not match, I bought it for raising Hand guard with this Parts.
Although the purpose is different, Plating and finishing are beautiful and satisfied.
Mirror got somewhat shaky, but for Hand guard, Mirror itself is attached.
As Mirror got out a little before, I think that visibility has become narrower, but the impact is Small..
I think that Mirror's position adjustment can be used without problems.
View detail
Why is there - - -
I offset Mirror and did not want to raise the height as much as possible so I bought this product.
The goods themselves are good things and it was possible to install as intended, but for our YAMAHA car installation we need two kinds of Right Screw and Left Screw, naturally we purchased it like that, but the attached car body The side fixed Bolt shape is "Mushroom type" When "Horizontal Type" Different shapes of.
I thought which one is better to look at which one is better, but it seems that it looks a little too different - - - In that respect, ☆ I made one Minus.
View detail
When Mirror relocation to company Mirror Holder
Used to relocate Mirror from MASTER and attach it to the company's Mirror Holder.
Because Z800OEM's RightMirror is Opposite Thread Screw, the company's Mirror Holder (M10 positive) In the meantime, it was necessary to install the Conversion Adapter in the meantime.
A manifestation of various Manufacturer's things, Material : I arrived at this product which is Stainless Steel but low price.
- Almost satisfied regarding installation.
The texture is good, it is enough length to cover the Rubber cover attached to Mirror, so Adapter can not be seen from the outside world.
- The position of Mirror also got a little high, and the visibility seems to have improved somewhat.
View detail