Reviews
Fits: YAMAHA , YAMAHA MT-25, YAMAHA FZ8, YAMAHA FZ1, YAMAHA MT-03
For MT-09 2021 and up
I was using a YAMAHA For M6, the less heavy one, and replaced it with this one.
The high-sider Mirror is EXACTLY hooked and the Handlebar vibration is pleasantly reduced.
It is not listed as compatible, but it will fit into the MT-09 from 2021 onwards with Exactly.
View detail
I'm glad it's rust resistant!
I used it to replace Mirror on an AddressV125 that a friend gave me! It works normally!
It would be nice if the design was a little more unique or better made!
View detail
Yamaha's Opposite Thread Screw A must-have for cars
I purchased this product when I switched to Napoleon OnMirror because my OEMMirror was rusting.
The Mirror position is slightly higher, but it was successfully installed.
View detail
It's neither good nor bad
Mirror by M-TEC (Shockproof Measured) was installed and when I took it to Plaza for inspection, I was told that it was not covered by the vehicle inspection, so I purchased it.
It is neither too expensive nor too expensive, but the position of Mirror is higher than expected, which is a little disappointing to look at.
View detail
Body side Opposite Thread Screw 10mm/Mirror side Opposite Thread Screw 10mm
When I installed DAYTONA's Screen on KTM DUKE200, the Bolt was by Masane, and I couldn't get it on without Adapter, so I bought an Adapter Set of Normal Thread Screw→Normal Thread Screw for Left Side and Opposite Thread Screw for Right Side. I bought Napoleon's Adapter Set of Screw→Normal Thread Screw, and Mirror was bolted to the Screen stay.
The screen is removed and the Mirror is directly attached, and the Left can be used, but the Right cannot use the adapter of the Opposite Thread Screw→Normal Thread Screw, and the Opposite Thread Screw→ is required. However, it is not available in Napoleon On. However, Napoleon On does not have it, and this is the one I found when I looked for it.
It's very convenient to return by Rose!
The left is 20mm for Napoleon On and 18.5mm for this product, but this is an error. The difference at a glance is that the Napoleon-On is a 17mm spanner and this product is a 14mm spanner.
View detail
Rose is for sale.
When I replaced the mirror, I didn't want to see the OEM PlatingScrew sticking out of the cover, so I bought this one, which was sold by Rose, because Napoleon On does not have both forward and reverse. It is a problem. View detail
Hmmm... subtle color difference.
[How is it used?
I bought this clamp to install on my brembo RCSRadial master. bremboOEM's MirrorHandlebar clamp (part number 110.A263.90) has a list price of 6,160 (tax included) Since the Mirror Adapter costs $3.99, it was stupid to spend a large amount of money on a Mirror Adapter, so I decided to endure with a patrimony (laugh).
Was the one you received as per Image?
The slightly different color is nice and looks like a pachimon! (Nice!)
Was the installation difficult?
Unfortunately, bremboOEM Bolt is not available (crying)
As you can see in the photo, the screw hole on the lower side of the Adapter comes in contact with the Bolt's flange, so the Bolt cannot go all the way into the Adapter. Well, in any case, it is an anti-theft material.:I was going to replace it with a Stainless SteelTorx bolt, though, so that's not a problem. Besides, bremboOEM bolt is just steel.
How was your experience with it?
No problem at all! If you look at it from 2 meters away, you can't tell the difference in color! (LOL)
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Where the colors are subtly different (laughs).
But Cost performance is top notch, so no problem!
Other items that would be helpful
Items to buy together:bremboOEM bolt is just steel, so it is recommended to replace it with a Stainless bolt.
Opinions and requests to Manufacturer:Please make it more like bremboOEM colors and master the path of pachimon! (LOL)
View detail
It is a must for Yamaha cars.
It is just a conversion Bolt but it scratches easily. monkey Wrench should not be used. It gets scratched easily. View detail
Scratches easily
Purchased for Mirror replacement.
I had heard that it was prone to scratches, so I worked with caution, but the scratches were firmly in place.
It's a cheap product, so maybe it can't be helped, but I'd like it to be made a little sturdier.
View detail
Fits: YAMAHA CYGNUS X, YAMAHA CYGNUS Gryphus
The quality of the exterior is poor.
[How is it used?
I bought a new CYGNUS X SR5 model for my commuter car and purchased this adapter to replace the mirror.
With this Adapter in place, I am using a Baren classic, Black color, from Tanax Napoleon Mirror.
Was the one you received as per Image?
Although it was as per Image... I thought it would be in the Blister pack like Tanax.
It came in a Petit bag, just like normal OEM Parts. I don't mind this, but...
The Adapter clashed with each other inside the bag, and became covered with scratches.... Or rather, the texture of the product is rather rough to begin with.
Please refer to the pictures.
Was the installation difficult?
For CYGNUS X, the Right Side is Opposite Thread Screw, so be careful.
Turn counterclockwise for Left and clockwise for Right to loosen. Also, the screw on the recessed side of the Adapter is an M10 Opposite Thread Screw.
The Mirror side also needs to be an Opposite Thread Screw.
How was your experience with it?
It fulfills the function itself, which is nice. The height isn't too high or too low.
BAREN classicMirror is a nice addition to the collection.
[Included Parts:were they on?
No, I don't! Tanax's Adapter came with a Washer, I believe.
I wish this came with it.
[Was there anything that disappointed you?
After all, is it the texture part? It's not a problem when it comes to function, but
This is a part that you will see all the time when you ride your motorcycle, so I hope you will pay attention to it.
To be honest, Tanax's Adapter has a beautiful Black Painting, so if you care about the appearance
We recommend Tanax.
View detail
I'm happy with how high Mirror can be positioned.
I bought and used the Tanax OffsetHolder and Cap to raise the height of the mirror, which made it easier to see behind me. I've been using my eyes nervously and had a lot of eye fatigue, but that seems to have lessened considerably! View detail
It can be used normally
I used it to put Mirror on the Other Brand Product.
It can be used normally.
Good thing it looks so OEM-chic and unassuming!
View detail
No problem
The quality of the product was absolutely perfect. View detail
Cancellation, please.
I ordered the wrong one and I need a Cancelation. View detail
Good texture
Bought it to install the Mirror for the SR400 on the CD125TBENLY50.
I was able to install it with no problems.
It can't be helped, but be aware that the height of the Adapter makes the Mirror more expensive.
For that reason, I think the Mirror Bracket should have a lower height.
View detail
Fits: MV AGUSTA BRUTALE 11, MV AGUSTA BRUTALE 11
External mirrors can be installed.
F4-BRUTALE cannot be installed on an external mirror.
BARRACUDA Barracuda Mirror Adapter (Pair) It is possible to install an external Mirror by using
However, since it is a blinker-integrated Mirror, the blinker needs to be placed separately.
That's part of the fun.
View detail
Is this what it looks like?
I'd like you to release the Black Anodized in Aluminum.
Also, Quantity:Pair (for Left and Right) I'd like to see the total weight published.
Previously. It's about making the bike lighter and losing weight yourself! And there was an article about...
View detail
Only the surface finish is disappointing
Purchased in place of the too expensive brembo OEM Mirror Holder
It would be helpful if the colors were displayed more clearly
Personally, I'd rather have all the colors Shot blast applied in advance to give it a cast-iron look I don't think it's strange to match with Master Cylinder, but …
Basically, I think Design is a finish that only fits the slippery shaving MASTER!
View detail
tightly packed
It is good if it becomes a little more Smallish, but because it can be fixed to Handlebar firmly I am very happy with it and it is stable even with a large piece of hardware installed View detail
Nice Screw Adapter
This TANAX Left-Handed Screw Adapter is very useful. It allows me to lift up the mirror a little bit, and to allow me to install a mount between the mirror and the screw adapter. View detail