Reviews
(Commuting) BattleMirror
I was concerned about the width of OEMMirror and purchased it. It is not only wide, but also tall, and is built as expected.
Compared to other products, the design is more OEM-like, so I think the balance with the overall body is good.
By the way, this is the second time I bought this because the one I bought before broke.
View detail
There is a slight difference.
I wanted to lower the OEMMirror position on my PCX a bit, so I purchased this one with a similar design.
It is a slight difference, but the overall impression will be different.
Level with no complaints about the ease of viewing.
The type of installation is tightened with a cap bolt.
I know they are designed to protect pedestrians, but even the slightest shock would loosen them, so I tightened them up quite a bit.
View detail
mirrors
perfect for my bike. Looks better than stock. Thanks About quality and texture About the feeling of use Products to buy together Difficulty of installation Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasingAbout quality and texture About the feeling of use About Design About Size Chart Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasingAbout quality and texture About the feeling of use Products to buy together Difficulty of installation Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasing View detail
StylishUP more bad
[How is it used?
Optimized for waiting ride in Touring
Was the one you received as per Image?
Large satisfactory, good looking
Was the installation difficult?
Anyone can install it easily.
How was your experience with it?
Satisfied with good rear visibility.
[Included Parts:were they on?
no problem
[Was there anything that disappointed you?
None
Point and hang of installation
Increased tightening after installation
Availability and comprehensibility of Instruction Manual/Points to note/Items to be purchased together/Opinions and requests to the Manufacturer
View detail
For Z125 Pro
Kawasaki Z125 Pro, Normal mirror is angular and a bit Large,
I was looking for a smaller, softer design, as it seemed a little too conspicuous,
I found this.
Normal mirror position on Z125 Pro, never good rearward visibility
(Most of the arms are shown) 、Quantity:Pair (for Left and Right) Both Spacer and (manufactured by TANA-X) Offset to the outside
Visibility improved.
In addition, TANA-X:Bracket Boots were attached to the lower part of the post.
I have used it for a year and a half with no problems and am satisfied with both the design and the feel of the product.
View detail
I think it is an Exactly Mirror to CYGNUS X.
[How is it used?
I installed it on my CYGNUS X that I use for commuting. I chose this Mirror because it has less protrusion, and I expect it to slip through.
Was the one you received as per Image?
The actual product is just like the Image.
However, when I actually used the Mirror, I found it to be solid for the price with little blurring.
Was the installation difficult?
CYGNUS is normally an M8 Normal Thread ScrewOpposite Thread Screw, so we used Y's Gear's M10 Conversion Adapter to install it.
The installation itself was not difficult, but the adjustment was a little troublesome.
How was your experience with it?
I'm switching from Mirror by Tanax, and it's so much easier to see than Mirror by Tanax!
I had been using Mirror by Tanax because it looked easy to slip through, but it looked naughty.
The Turtle Mirror has a more OEM look and is wider than the Turtle Mirror, which allows you to slip through, but also allows you to see behind you.
[Included Parts:were they on?
As shown in the image.
[Was there anything that disappointed you?
No, there is not! It is important to note that this is not a planar mirror, but a convex Lens, and it is a Mirror that can properly see behind it.
If this were a flat mirror, it would be a useless Mirror.
View detail
Mirror Replacement
OEM replaced it with this one because it looks like a snail's horn.
I think the Mirror position has been lowered considerably and the Sharpness has increased.
View detail
I can see behind me now.
The mirrors were a little hard to see, so I changed them, but HURRICANE is cheap! The mirror is a little low when installed as it is, so I put a 10mm bolt extension between the two mirrors so I can see the back of the car perfectly. I chose this Mirror because of the price, but there is a hole in the Mirror arm to cut out the meat or not, and I don't dislike the design. It also comes with a 10mm Opposite Thread Screw Adapter, so it seems to be highly universal. View detail
Design Priority Products
The design is sharp and excellent, with a wide horizontal field of view but poor in the vertical direction. The Bolt is not well fixed to the Bracket, and it is easy to move, so improvement is desired. View detail
CBR250RMirror replacement
Changed from OEM Cowl mount to Handlebar Mounting in hopes of increasing visibility range.
The result is almost satisfactory, with less reflection of my arms, etc., and a wider visible range.
Handlebar has already been changed to HURRICANE Pipe handle.
The base of the Mirror rests on the Cowl in the fully locked state, but the Cowl bends, so you can use the Mirror without modification.
Handlebar lockable.
With the loss of Mirror from Cowl, has it Refreshed a bit in terms of design?
View detail
Compact.
It is easy to install with two sizes and an Opposite Thread Screw. It is easy to install. The width has also been made narrower, making it perfect for narrow scenes. It is also suitable for spare parts because of its good visibility and cost performance. View detail
Slim.
I am happy with the low price and solid construction, perfect as a Spare. The width is also slim, so tight spaces are no problem. View detail
HURRICANE Turtle
I used the tanax rearview mirror and the Hurricane separation handle before, it didn't look good. Now I replace the Hurricane's rearview mirror with a good view, and the overall coordination is very good. View detail
Grom JC61 '15
Used for groms
For very short, KITACO's Z?Mirror is the standard.
I thought such a sharp design would be suitable for the modern forme Grom!
Quantity:Pair (for Left and Right) The price is very reasonable!
We don't know yet if there will be any blur due to recoil during production, but
I'm prepared to pay the price, but...
I have high hopes for HURRICANE's ability.
View detail
It was low.
I bought this one because I wanted a compact mirror as I slip through a lot on my Scooter. I thought the texture was normal. I thought it was lower than I expected, but I used the Mirror screw Conversion Adapter that I had left at home beforehand and raised it to the bottom. If it is originally a quantity of positive 8mm and reverse 8mm:Set, but due to the availability of the adapter, the quantity is 10mm.:I bought a set, and I can use OEM Mirror ScrewCover with or without the Adapter. It is easy to see the mirror, but I can't see anything behind me. Turn around to check the rear! View detail
Small but easy to see
For a small camera, it is relatively easy to see. There is no blurring. Easy to install and easy to adjust. View detail
Demon Slipping Spec.
It's been raining so I've been working on it. It's the same width as the OEM Bar End, so it's easier to slip through. I'm not sure if this is a good idea or not, but I think it's a good idea for people who want a compact mirror but don't want it to be hard to see. The best point is that the mirror doesn't shake anymore even with the strong vibration of VTwin. View detail
Installed on the previous season Grom
It is easier to see than the OEM round mirror, but when I wash the car, grease leaks from the gap between the mirror and the body.
If you don't care about it, it's fine, but if you're like me and want to coate, leaking Grease is a big deal.
View detail
Smaller and narrower, Refreshing.
I installed it on a 150cc Underbone MODEL (Yamaha Exciter).
Instead of the Right Side Reverse Thread, which is unique to Yamaha cars, I chose the M10 Orthodontic/M10 Orthodontic Adapter (MIRAX102 or Tanax H-10), which is the most universal type.
I felt that the overhang of the OEM Mirror was too large, so I searched for a compact and short one, and I came across this HURRICANE VBlade.
The overall design is similar to OEM, but without the custom look.
I want to make the total length shorter than OEM and refreshing.
The mirror surface is not too large.
Low price
Since it's Mirror, I want a certain level of quality and durability.
I want a brand I know.
I think I can recommend it to those people.
In the case of my Motorcycle, the overhang is the same as the OEM ratio of Quantity:Pair (for Left and Right) Each is now about 4cm shorter, and the real width around the Handlebar is now a little Slim.
The size of the mirror itself is small, so the rear view is a little bit inferior, but I am satisfied because the formme is as expected.
The detailing is the same as OEM. I am also satisfied with this product because it is resistant to shaking and does not resonate.
It has RubberBoots on the mounting, which is good for MODELS that have a Cover such as Scooter.
If you want to put it on NAKED system, you can remove Nut once and pull out Boots, so you can remove it and throw it away.
Also, Boots is a Material:The lock nut to fix the angle of the mirror is difficult to turn when the boots are attached because it is hard like soft plastic rather than rubber.
It's like inserting 14mm Spanner and tighten it well. If you don't tighten it well, it will be loose and ruined.
In relation to the safety standard (area) for the model MODEL after 2007 (2007). [Color] Not Clear
Therefore, it is your own responsibility to install it on the recent MODEL.
View detail
A good Mirror that goes with any motorcycle in a safe manner
I installed it on my Yamaha Max star125.
Edge is smart and it's MT09 OEM Mirror style.
It's a HURRICANE, so the quality is good because it's a solid manufacturer.
Also, this Mirror even comes with screws that correspond to the M8 and M10 screws and reverse screws, which is nice.
Visibility, unfortunately, did not feel so good.
It's much better than nothing, though.
There is no lock by nut. When it's loose, it will be plunged all at once.
Well, considering the price, it's a good enough Mirror.
View detail